• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.690-692
• /
• 2003

In this paper, we have investigated characteristics of radio frequency for double gate MOSFET with 50nm main gate in according to variation of side gate length. We could know the increasement of cut-off frequency as the side gate length is lower. As a result, we could know the most optimum performance characteristics when side gate length was 70nm. In this time, the DG MOSFET of side gate with 70nm has very high cut-off frequency like 41.4GHz.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.33-37
• /
• 1995

A side-cut grinding generates a machining error by the decrease of the quill rigidity. In this paper, The effect on the grinding force, machining error and surface roughness due to the change of the quill rigidity is investigated experimentally. The slenderness ratio of the quill is a significant factor to analyse the change of the grinding force and machining error.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.900-904
• /
• 1997

A problem in the grinding process using the machining center(MC) with a small diametric wheel is the machining error due to due to decrease of quill diameter. In this paper, a side-cut grinding is performed with a vitrified bonded CBN wheel by the MC, and the relation between grinding force and machining error for grinding conditions is investigated experimentally. It is show that the normal force has a significant effect on the machining error.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.98-103
• /
• 2012

One of the problems in the grinding process using the machining center(MC) with a small diametric wheels is machining error due to decrease of the quill diameter. In this thesis, side-cut grinding is performed with a vitrified bonded CBN wheel on the machining center to establish the basis of the grinding using MC. The grinding force and machining error are investigated experimentally for the change of the machining condition. It is possible to estimate the machining performance by the ratio of the setting depth of cut and actual depth of cut. In addition, the relation between normal grinding force and machining error is presented by the experimental formula.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.38-42
• /
• 1995

In this paper, a theoretical analysis is presented on the mechanics for the side-cut grinding by electrodeposited CBN wheel of a hemispheric type. Each of the grinding force components is calculated by using the geometrical model. It is also presented that experimental results show grinding forces for grinding variable such as wheel speed, feed speed,depth of cut, and grinding wheel positions. The experimental results are found to be in good agreement with those predicted by the analytcal calculation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.5
• /
• pp.36-41
• /
• 2013

One of the problems in grinding process using a machining center(MC) with a small diametric wheels is machining error due to decrease of the quill diameter. In this study, side-cut grinding is performed with a vitrified bonded CBN wheel on the machining center. Grinding experiments are performed at various grinding conditions including quill length, quill diameter and depth of cut. The effect on the grinding force, machining error and surface roughness due to the change of the quill rigidity are investigated experimentally. The slenderness ratio of the quill is significant factor to analyse the change of the grinding force and machining error.

• Journal of Korean Society of Forest Science
• /
• v.89 no.3
• /
• pp.397-404
• /
• 2000

This study was carried out to investigate the influence of the road structure and site conditions on side-ditch stability of forest road. For experimental purposes, the forest road in the Kwangrung Experimental Forest, Korea Forestry Research Institute, was chosen as a study site. A total of 556 plots wes set up as every longitudinal gradient changing points by belt-transect method. Data of 10 road structural characteristics and side-ditch stability were collected from each plot and analysed by Quantification II. The main factors in order of partial correlation coefficient were longitudinal gradient, road position, inclination of cut-slope, constituent material of cut-slopes, distance of surface flow, cross-sectional shape of road, pavement material, vegetation of cut-slopes and length of cut-slope. The erosion of side-ditch of forest road occurred in the following cases; more than 8% of the longitudinal gradient, road position of hill under side and foot hill, more than $50^{\circ}$ of inclination of cut-slope, constituent material of cut-slopes of hard soil and gravel soil, more than 80m of distance of surface flow, pavement material with earth or gravel, more than medium covered of vegetation of cut-slopes, and the straight and convex form of road-bed.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1782-1788
• /
• 2007

This study analyzed ground settlement and ground stress depending on tunnel excavation and the ground reinforcing grouting methods for double line road tunnel through deep weathered zone. Diameter of double line road tunnel was approximately 12m and umbrella arch method and side wall reinforcing grouting were applied. The ring-cut split excavation method and CD-cut excavation method for excavation method were applied. Analysis of failure rate and vertical stress ratio show that the tunnel for which the height of the cover(H) was higher than four times the diameter, it can be considered a deep tunnel. Comparisons of various excavation and ground reinforcement methods were showed that CD-cut method results in lower surface and crown settlement, and lower failure rate than where using Ring-cut split method. In addition the side wall reinforcing grouting resulted in reduction of tunnel displacement and settlement.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.685-690
• /
• 2000

In this study relationship between relief angles and chatter vibration in turning was examined by using the direct cutting test, in which the cutting depth of a tapered workpiece is varied continuously and the limiting depth of cut is measured at the time when chatter occurs. Test results reveal that 1) limiting depth of cut increases is proportion to side relief angles between 0$^{\circ}$ and 3$^{\circ}$, 2) limiting depth of cut does not show any evident change in spite of side relief angle increased from 3$^{\circ}$ to 12$^{\circ}$, 3) also limiting depth of cut does not change despite front angle change from 0$^{\circ}$ to 12$^{\circ}$.

• Journal of the Korean housing association
• /
• v.21 no.5
• /
• pp.137-144
• /
• 2010

The purpose of this study is to clarify locational characteristics and the road systems of existing 22 old settlements in Cheongju downtown of Korea. These old settlements are classified largely into two types by geographical feature; Hill type located in ridge and Valley type in the valley from the ridge. The Hill type is further categorized into San-rock located on ridge and Gogae located on hillside, and the Valley type into closed large and small valley, that is, Daegok and Sogok by the shape and size of the valley. The road systems are classified into outer road, approaching road, inner road, and side road. In San-rock type villages, Inner road is changed side roads by new arterial road, and new ones become inner road. The outer road are almost cut off, but side roads maintain. In the case of the Gogae type, main road becomes inner road, maintain old hierarchical road, and in other cases, villages are formed around side roads derived from main road, and outer road and inner road are cut off. Among the Valley type, Daegok type maintains old hierarchical road, while for Sogok type, outer roads are cut off, and new roads are outer road.