• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 춘계종합학술대회
• /
• pp.690-692
• /
• 2003

본 논문에서는 main gate 50nm를 갖는 double gate MOSFET에서 side gate의 길이변화에 따른 주파수 특성을 조사하였다. side gate길이가 감소할수록 컷오프 주파수는 증가하는 것을 볼 수 있었다. 결과적으로 side gate 길이가 70nm일 때 최적의 동작 특성을 보였으며, 이때 컷오프 주파수는 41.4GHz로 매우 높은 컷오프 주파수를 갖음을 알았다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.33-37
• /
• 1995

A side-cut grinding generates a machining error by the decrease of the quill rigidity. In this paper, The effect on the grinding force, machining error and surface roughness due to the change of the quill rigidity is investigated experimentally. The slenderness ratio of the quill is a significant factor to analyse the change of the grinding force and machining error.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.900-904
• /
• 1997

A problem in the grinding process using the machining center(MC) with a small diametric wheel is the machining error due to due to decrease of quill diameter. In this paper, a side-cut grinding is performed with a vitrified bonded CBN wheel by the MC, and the relation between grinding force and machining error for grinding conditions is investigated experimentally. It is show that the normal force has a significant effect on the machining error.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.98-103
• /
• 2012

One of the problems in the grinding process using the machining center(MC) with a small diametric wheels is machining error due to decrease of the quill diameter. In this thesis, side-cut grinding is performed with a vitrified bonded CBN wheel on the machining center to establish the basis of the grinding using MC. The grinding force and machining error are investigated experimentally for the change of the machining condition. It is possible to estimate the machining performance by the ratio of the setting depth of cut and actual depth of cut. In addition, the relation between normal grinding force and machining error is presented by the experimental formula.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.38-42
• /
• 1995

In this paper, a theoretical analysis is presented on the mechanics for the side-cut grinding by electrodeposited CBN wheel of a hemispheric type. Each of the grinding force components is calculated by using the geometrical model. It is also presented that experimental results show grinding forces for grinding variable such as wheel speed, feed speed,depth of cut, and grinding wheel positions. The experimental results are found to be in good agreement with those predicted by the analytcal calculation.

• 한국기계가공학회지
• /
• 제12권5호
• /
• pp.36-41
• /
• 2013

One of the problems in grinding process using a machining center(MC) with a small diametric wheels is machining error due to decrease of the quill diameter. In this study, side-cut grinding is performed with a vitrified bonded CBN wheel on the machining center. Grinding experiments are performed at various grinding conditions including quill length, quill diameter and depth of cut. The effect on the grinding force, machining error and surface roughness due to the change of the quill rigidity are investigated experimentally. The slenderness ratio of the quill is significant factor to analyse the change of the grinding force and machining error.

• 한국산림과학회지
• /
• 제89권3호
• /
• pp.397-404
• /
• 2000

임도 옆도랑침식에 영향을 미치는 요인의 평가 및 안정도 판별을 위하여 광릉시험림의 임도를 대상으로 조사를 실시한 결과 침식에 미치는 기여순위는 종단물매, 시설위치, 절토사면경사, 절토사면구성물질, 유하거리, 노면형태, 노면재료, 절토사면피복도, 절토사면길이 순으로 나타났다. 임도 옆도랑침식을 유발하는 요인을 평가하면, 종단물매는 8% 이상, 임도시설위치는 산록(山麓)과 중복(中腹), 절토사면경사는 $50^{\circ}$ 이상, 절토사면토성은 견질토사, 자갈섞인 토사, 호박돌섞인 토사, 유하거리는 80m 이상의 지역에서, 그리고 노면재료는 토사도(土砂道)와 자갈부설도에서, 노면형태의 경우에는 철(凸)형과 직선형, 절토사면 피복도(被覆度)는 피복도가 중(中)이상인 곳에서 임도 옆도랑침식이 발생할 가능성이 높은 것으로 예측(豫測)되었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1782-1788
• /
• 2007

This study analyzed ground settlement and ground stress depending on tunnel excavation and the ground reinforcing grouting methods for double line road tunnel through deep weathered zone. Diameter of double line road tunnel was approximately 12m and umbrella arch method and side wall reinforcing grouting were applied. The ring-cut split excavation method and CD-cut excavation method for excavation method were applied. Analysis of failure rate and vertical stress ratio show that the tunnel for which the height of the cover(H) was higher than four times the diameter, it can be considered a deep tunnel. Comparisons of various excavation and ground reinforcement methods were showed that CD-cut method results in lower surface and crown settlement, and lower failure rate than where using Ring-cut split method. In addition the side wall reinforcing grouting resulted in reduction of tunnel displacement and settlement.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.685-690
• /
• 2000

In this study relationship between relief angles and chatter vibration in turning was examined by using the direct cutting test, in which the cutting depth of a tapered workpiece is varied continuously and the limiting depth of cut is measured at the time when chatter occurs. Test results reveal that 1) limiting depth of cut increases is proportion to side relief angles between 0$^{\circ}$ and 3$^{\circ}$, 2) limiting depth of cut does not show any evident change in spite of side relief angle increased from 3$^{\circ}$ to 12$^{\circ}$, 3) also limiting depth of cut does not change despite front angle change from 0$^{\circ}$ to 12$^{\circ}$.

• 한국주거학회논문집
• /
• 제21권5호
• /
• pp.137-144
• /
• 2010

The purpose of this study is to clarify locational characteristics and the road systems of existing 22 old settlements in Cheongju downtown of Korea. These old settlements are classified largely into two types by geographical feature; Hill type located in ridge and Valley type in the valley from the ridge. The Hill type is further categorized into San-rock located on ridge and Gogae located on hillside, and the Valley type into closed large and small valley, that is, Daegok and Sogok by the shape and size of the valley. The road systems are classified into outer road, approaching road, inner road, and side road. In San-rock type villages, Inner road is changed side roads by new arterial road, and new ones become inner road. The outer road are almost cut off, but side roads maintain. In the case of the Gogae type, main road becomes inner road, maintain old hierarchical road, and in other cases, villages are formed around side roads derived from main road, and outer road and inner road are cut off. Among the Valley type, Daegok type maintains old hierarchical road, while for Sogok type, outer roads are cut off, and new roads are outer road.