• Journal of The Korea Institute of Healthcare Architecture
• /
• v.28 no.4
• /
• pp.61-69
• /
• 2022

Purpose: In response to the rapid spread of COVID-19 in 2020, the government supported facilities and equipment through the 'Urgent Isolation Ward Expansion Project'. Design and remodeling of efficient negative pressure isolation facilities had to be done in a short period of time, and the performance gap between facilities was very large because the types of hospitals and wards of existing medical facilities were diverse. In order to secure the stability of isolation wards between medical facilities and reduce the facility gap, guidelines for planning isolation wards considering the diversity of each hospital should be appropriately presented. In consideration of these points, this study aims to provide basic data for future remodeling guidelines for each plan type of the negative pressure isolation ward first. Methods: We analyzed the plans before and after the change of 13 case hospitals that performed the urgent care bed expansion project for COVID-19 confirmed patients. Before the remodeling, the current status of the facility was analyzed according to the type of corridor, the location of the nursing station, and the location of the elevator. After remodeling, the flow of medical staff and patients, the flow of entry and exit of clean and contaminated items, and the space of negative pressure and non-negative pressure areas. Results: The ward type was divided into three types according to the corridor type and room arrangement: double loaded corridor type with two side wards, race track type with one side ward, and race track type with two side wards. Based on these three types, the standard floor plan type of the isolation ward was proposed in terms of the location of the elevator bank and Nurse station. Implications: When the existing general ward is converted into a negative pressure isolation ward, this study can be a basic data to present customized guidelines for each ward type.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.2
• /
• pp.183-191
• /
• 2012

The objective of this study was to evaluate the plantar foot pressure of skilled and unskilled players during a free throw. The experiment performed here in measured the movement route of the mean foot pressure, maximum foot pressure, and center of pressure in four event zones (ready, maximum knee flexion, release event, and maximum knee extension) for both groups while they were wearing the plantar foot pressure measurement equipment under identical conditions. The major findings are as follows. When getting ready (RD) during a free throw, the skilled player group had higher mean and maximum foot pressures, although neither variable showed significant differences statistically. For the maximum knee flexion (MF) during a free throw, the skilled player group had higher mean and maximum foot pressures, but only the mean foot pressure significantly differed statistically. For the release event (RE) during a free throw, the unskilled player group had higher mean and maximum foot pressures, but only the mean foot pressure significantly differed statistically. During the maximum knee extension (ME) of a free throw, the unskilled player group had a higher mean foot pressure, and the skilled player group had a higher maximum foot pressure. No significant correlation was found between the two groups. For the skilled player group, movement towards the center of pressure showed a stable form that moved from the rear to the front and from side to side during a free throw. For the unskilled player group, movement towards the center of pressure was unstable, which made it impossible to move from the rear to the front and from left to right.

• Journal of Oral Medicine and Pain
• /
• v.22 no.2
• /
• pp.327-339
• /
• 1997

This study aimed at evaluating tile relationship between pressure pain threshold(PPT) and electromyographic(EMG) activity in 30 healthy volunteers and 30 patients with temporomandibular disorders. PPTs were determined with electric pressure algometry over masseter, temporalis anterior, sternocleidomastoid, and trapezius muscle during resting and clenching. To obtain more reliable result, two examiners measured PPTs two times on each muscles, randomly. Resting and clenching EMG activity and tenderness of all muscles were measured to evaluate the relationship with PPTs. The collected data were processed by SAS/STAT program. The obtained results were as follows : 1. Pressure pain thresholds in tendered muscles were lower than those in non-tendered muscles. This tendency was more prominant in masticatory muscles than in cervical muscles and in clenching than in resting. 2. There ware a tendency of higher PPTs in unaffected side than in affected side, but there were no significant difference statistically. 3. There wert no difference of PPTs between in preferred side and in ipsilateral side, significantly. 4. There was a significantly positive correlation between resting and clenching PPTs, but there were no correlation between PPTs and EMG activities. 5. Comparison of EMG activity between in higher group and in lower group by resting PPTs didn't show any significant difference. But resting EMG activity in the higher group of clenching PPTs were lower, on the contrary, clenching activity were higher than those in lower groups of clenching PPTs. From this results, the author concluded that the clenching PPTs was more important than resting PPTs in diagnosis of muscle dysfunction. And the author recommanded that all of three following test were performed for the proper diagnosis and treatment of orofacial Pain : muscle tenderness, EMG activity, and PPT.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.17-25
• /
• 2019

An intake of Aircraft becomes S-shaped geometry due to spatial limitation or procuring survivability. But curvature of the S-shaped geometry makes secondary flow or flow separation which is the cause of non-uniform pressure distribution. In this study, boundary layer suction is applied to RAE M 2129 S-Duct by attaching sub duct. Design variable is suction location and angle. A mass flow rate drawn out by suction at the sub duct outlet is constant over every model. A grid dependency test was conducted to verify validity of computation. The comparison among the CFD (Computation Fluid Dynamics), ARA experimental result, and ARA computation result of non-dimensional pressure distribution on the Port side and Starboard Side confirmed the validity of CFD. In this study, Distortion Coefficient was used for evaluating aerodynamic performance of S-Duct. The analysis, which was about flow separation, vortex, mass flow rate distribution, and pressure distribution were also investigated. Maximum 26.14% reduction in Distortion Coefficient was verified.

• International Journal of Fluid Machinery and Systems
• /
• v.7 no.1
• /
• pp.28-33
• /
• 2014

In order to research the relationship between the tip clearance and leakage flow of centrifugal compressor, a high speed centrifugal compressor was investigated by using CFD. A numerical study on the effect of four different rotor tip clearance sizes of centrifugal compressor, which were 0.5times, 1 times, 1.5times and 2.0times of the design tip clearance, was carried out. Efficiency and pressure ratio curves were obtained under different mass flow. The reasons of the clearance vortex and the factors of vortex size were analyzed. The result indicated that with the increase of tip clearance size, the performance of the compressor changed obviously, the performance parameters such as efficiency and pressure ratio tended to decrease obviously. While, the leakage flow does not always lead to leak vortex. The strength of the vortex increased with the tip clearance. The size of leak vortex was affected by the pressure difference between the suction side and the pressure side of blade tip.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3_1spc
• /
• pp.551-557
• /
• 2013

The heat transfer performance and pressure drop characteristics of brazed-plate heat exchangers with 20 and 30 plates were experimentally measured and analyzed in this study. The mass flow rates of the heat exchangers with 20 and 30 plates were fixed at 0.6 and 0.9 kg/s for the low temperature side, respectively. The mass flow rate for the high temperature side was controlled from 0.2 kg/s to 1.2 kg/s. The inlet temperatures for the high and low temperature sides were $10^{\circ}C$ and $7^{\circ}C$, respectively. The heat transfer characteristics were not influenced by the number of plates. The pressure drop at the heat exchanger with 30 plates was slightly higher than that with 20 plates. The values calculated from the correlations based on gasket plate heat exchangers were compared with the experimental results. It was found that the predicted Nusselt numbers for the gasket plate heat exchangers were about 5% to 20% lower than the measured Nusselt numbers for the brazed plate heat exchangers. However, a pressure drop comparison showed that the calculated pressure drops at the gasket plate heat exchangers were less than half of the measured pressure drops at the brazed plate heat exchangers.

• Journal of Korean Physical Therapy Science
• /
• v.17 no.3_4
• /
• pp.29-39
• /
• 2010

Purpose: The purpose of this study was to examine the effect of foot position and lifting an object on muscle activity and foot pressure during sit to stand(STS) in hemiparetic patients. Methods: Fourteen patients participated in this study. Surface electromyography was used to collect muscle activity and foot pressure measurement system was used to analyze foot pressure in hemiparetic side. Three different foot position was assumed(anterior, neutral, posterior) in hemiparetic side. The repeated two-way analysis of variance and multiple comparisons were conducted to determine statistical significance with a significance level of 0.05. Results: The results were as follows. 1) Lower extremity muscle activity was significantly higher(p<0.05) in biceps femoris and tibialis anterior muscle during STS without holding an object. With changing positions of the affected foot, muscle activity was significantly increased (p<0.05) in vastus medialis and lateral gastrocnemius when the foot was positioned in posterior. 2) There was no significant difference(p>0.05) in foot pressure during STS with object holding and foot positioning. Conclusion: Muscle activity showed a significant increase when the foot was positioned in posterior in comparison to the muscle activity when the foot was in neutral or anterior position.

• Journal of computational fluids engineering
• /
• v.6 no.3
• /
• pp.27-31
• /
• 2001

For rapid and abrupt control of a missile in supersonic flight, side jet on a missile body is found to be a useful device as evidenced by recent missile development at several nations. The magnitude of the side jet and the duration of it decide the level of control of such a missile system. In this paper, the aerodynamic characteristics of the side jet device itself are examined in terms of key parameters such as the side jet nozzle geometry, the chamber pressure and temperature. Specifically attention is paid to the effect of the chamber shape between the straight nozzle and the bent nozzle by 90 degrees on the nozzle flow properties. The thrust magnitudes are compared between the two shapes. Whether the way the nozzle is bent at the joint affects the nozzle performance is also investigated. Effects of the length and the divergence angle of the nozzle on the thrust are also quantified among three different side jet nozzles.

• Journal of Animal Science and Technology
• /
• v.55 no.6
• /
• pp.545-549
• /
• 2013

The optimal conditions for applications of an atmospheric pressure plasma (APP) jet for the inactivation of Salmonella Typhimurium in chicken breast and pork loins were investigated. APP jet treatment for 10 min (versus 5 minutes) showed a higher inactivation of S. Typhimurium in an agar plate, with the best effect at a distance of 20 mm. A treatment on both sides (both-side treatment) for 2.5 + 2.5 min showed a greater inhibition on S. Typhimurium growth compared to single-side treatment for 5 min, with reduction levels of 0.66 log CFU/g in chicken breast and 1.33 log CFU/g in pork loin, respectively. However, there was no significant difference between single-side treatment for 10 min and both-side treatment for 5 + 5 min in chicken breasts and pork loin samples. In conclusion, APP jet treatment conditions, including distance, time, and direction, may affect the inactivation efficiency of S. Typhimurium. In this experiment, distance of 20 mm and both-side treatment were the best conditions. Therefore, the optimal APP jet treatment conditions were evaluated to maximize its practical efficiency.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.337-345
• /
• 2008

this study, three dimensional surface pressure distributions of SWIM whose main wing has NACA4412 airfoil with NACA0012 flaps were experimentally measured by pressure sensitive paint. Surface pressures on suction and pressure sides of the wing were measured by changing an angle of attack at a Reynolds number of 3.1x105 in KARI 1m subsonic wind tunnel. The experimental results showed that as an angle of attack increases minimum pressure region on a suction side moved from the wing root to the tip and low pressure region around trailing edge of the wing tip which causes wing tip vortex was observed. Although low pressure region at the tip still observed at an angle of attack 15 deg., other area on a suction side showed flat pressure distribution in a span-wise direction. It was also observed that the mean value of pressure coefficients was about 0.077 through a comparison between PSP and pressure taps at the same test conditions.