• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.234-234
• /
• 2010

최근 CMOS 소자 크기가 축소됨에 따라 소스와 드레인 영역에서의 접촉저항을 줄이기 위하여, 실리사이드 공정이 많이 연구되고 있다. 실리사이드 물질로서 NiSi는 낮은 저항률과 낮은 실리콘 소모, 낮은 공정온도, 등의 장점을 가지고 있다. 그러나, 실리사이드 형성으로 인한 나노소자의 소오스/드레인에서정션(junction) 누설전류의 증가는 큰 문제가 되므로 실리콘과 실리사이드 계면의 특성이 중요하다. 본 연구에서는 니켈을 이용한 실리사이드 형성시 계면 활성제인 에틸 요오드를 이용하여 실험을 진행하였다. 금속 유기 전구체인 MABONi을 사용하여 ALD 방식으로 증착 한 니켈 박막과 니켈 핵 형성시 계면활성제인 에틸요오드의 처리 방법에 따른 Ni-silicide 박막의 특성을 비교, 분석하였다. 먼저 자연산화막을 건식식각으로 제거한 뒤, 첫 번째 샘플에서는 10회의 주기로 초기 니켈을 증착한 뒤, 에틸요오드로 니켈의 표면 위를 처리하고, 다시 200회의 주기로 니켈을 증착하였으며, 두 번째는 첫 번째 방식에서 에틸요오드 주입 시 동시에 수소도 함께 주입하였다. 세 번째는 비교를 위해 에틸요오드 처리를 하지 않고 니켈 박막만을 증착 하였다. 이어서, 각 샘플을 급속 열처리 장비에서 $400^{\circ}C$부터 $900^{\circ}C$까지 각각 30sec간 열처리를 진행후, 반응하지 않은 잔여 니켈을 제거한 후, XRD(x-ray diffraction), AES(auger), 그리고 4-point probe 등을 이용하여 형성된 실리사이드의 특성을 분석하였다. 에틸요오드와 함께 수소를 주입한 경우 계면에서의 산소 불순물과 카본 성분이 효과적으로 제거되어 $400^{\circ}C$에서 $2.9{\Omega}/{\Box}$ 의 낮은 면저항을 가지는 NiSi가 형성되었고 모든 온도구간에서 다른 샘플에 비하여 가장 낮은 면저항 분포를 보였다. 이는 분해 흡착된 요오드에 의한 계면 특성 향상과 카본 성분이 포함된 잔여물들이 수소처리에 의해 효율적으로 제거되어 실리사이드의 특성이 향상되었기 때문이다. 계면활성제를 사용하지 않은 경우에는 $500^{\circ}C$에서 NiSi가 형성되었다. 반면에 에틸요오드로만 표면을 처리한 경우에는 니켈과 실리콘 계면에서의 카본 성분에 의하여 silicidation 이 충분히 일어나지 않았다. 이러한 결과는 향후 45nm 이하의 CMOS 공정상에서 소스와 드레인의 낮은 누설전류를 가지고, 접촉저항을 줄이기 위한 니켈 실리사이드 형성에 큰 도움을 줄 것으로 기대된다.

• Tribology and Lubricants
• /
• v.22 no.6
• /
• pp.314-319
• /
• 2006

In this paper, the friction and wear characteristics of contact type sealing unit far a water turbine have been presented. The sealing unit for a small hydropower generation is to stop a leakage of circulating water from an outside of an impeller to an inside of a rolling bearing. The friction heating between a seal ring and a seal seat may radically increase a surface temperature in which increase a power loss and wear on the rubbing surface. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Victors hardness and the hardness of silicone carbide of SiC is 714.1 in Victors hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces are a dry friction, a water film friction and a mixed friction that is contaminated by a dust, silt, and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat in primary sealing unit. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.6
• /
• pp.291-295
• /
• 2013

Surface chemical modification via air and hydrogen heat treatment was found to relieve the aggregation of nanodiamond (ND) seed particles and lead to a significantly enhanced nucleation density for ultrananocrystalline diamond (UNCD) film growth. After heat treatment in air and hydrogen, modification of surface functionalities and increase in the zeta potential were observed. Mean size of the ND aggregates was also dramatically reduced from ${\sim}2{\mu}m$ to ~55 nm. Si surface seeded with ND particles heat-treated at $600^{\circ}C$ in hydrogen produced a much higher nucleation density of ${\sim}2.7{\times}10^{11}cm^{-2}$ compared to untreated ND seeds.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.208.1-208.1
• /
• 2015

최근, 차세대 투명 디스플레이 구동소자로서 산화물 반도체를 이용한 Transparent Amorphous Oxide Semiconductor (TAOS) 기술이 큰 주목을 받고 있다. 산화물 반도체는 기존의 a-Si에 비해 우수한 전기적인 특성과 낮은 구동전압 그리고 넓은 밴드 갭으로 인한 투명성의 장점들이 있다. 그리고 낮은 공정 온도에서도 제작이 가능하기 때문에 유리나 플라스틱과 같은 다양한 기판에서도 박막 증착이 가능하다. 하지만 기존의 furnace를 이용한 열처리 방식은 낮은 온도에서 우수한 전기적인 특성을 내기 어려우며, 공정 시간이 길어지는 단점들이 있다. 따라서 본 연구에서는 산화물 반도체중 In-Ga-Zn-O (IGZO)와 In-Sn-O(ITO)를 각각 채널 층과 게이트 전극으로 이용하였다. 또한 마이크로웨이브 열처리 기술을 이용하여 기존의 열처리 방식에 비해 에너지 전달 효율이 높고 짧은 시간동안 저온 공정이 가능하며 우수한 전기적인 특성을 가지는 투명 박막 트랜지스터를 구현 하였다. 본 실험은 glass 기판위에서 진행되었으며, RF sputter를 이용하여 ITO를 150 nm 증착한 후, photo-lithography 공정을 통하여 하부 게이트 전극을 형성하였다. 이후에 RF sputter를 이용하여 SiO2 와 IGZO 를 각각 300, 50 nm 증착하였고, patterning 과정을 통하여 채널 영역을 형성하였다. 또한 소자의 전기적인 특성 향상을 위해 마이크로웨이브 열처리를 1000 Watt로 2 분간 진행 하였고, 비교를 위하여 기존 방식인 furnace 를 이용하여 N2 분위기에서 $400^{\circ}C$로 30분간 진행한 소자도 병행하였다. 그 결과 마이크로웨이브를 통해 열처리한 소자는 공정 온도가 $100^{\circ}C$ 이하로 낮기 때문에 glass 기판에 영향을 주지 않고 기존 furnace 열처리 한 소자보다 전체적으로 전기적인 특성이 우수한 것을 확인 하였다.

• Korean Journal of Materials Research
• /
• v.4 no.4
• /
• pp.453-458
• /
• 1994

$(Ba_{0.5}Sr_{0.5)/TiO_3$(BST) thin films were prepared for the application of 256 Mb DRAM by RF magnetron sputtering. The crystallinity of BST thin films increased with increasing deposition tempera lure. The composition of thin films was $(Ba_{0.48}Sr_{0.48)/TiO_{2.93}$ Pt/Ti barrier layer suppressed the diffusion of Si into BST layer. The films showed a dielectric constant of 320 and a dissipation factor of 0.022 at 100 kHz. the change of capacitance of the films with applied voltage was small, showing paraelectric property. The charge storage density and leakage current density were 40fC/$\mu \textrm{m}^{2}$ and 0.8$\mu A/\textrm{cm}^2$, respectively at a field of 0.15 MV/cm. The BST films obtained by RF magnetron sputtering appeared to be potential thin film capacitors for 256 Mb DRAM application.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.11
• /
• pp.2385-2390
• /
• 2009

N-doped ZnO thin films with c-axis preferred orientation were prepared on p-Si(100) wafers, using an RF magnetron sputter deposition. For ZnO deposition, $N_2O$ gas was employed as a dopant source and various deposition conditions such as $N_2O$ gas fraction and RF power were applied. The depth pofiles of the nitrogen [N] atoms incorporated into the ZnO thin films were investigated by Auger Electron Spectroscopy(AES) and the nano-scale structural characteristics of the N-doped ZnO thin films were also investigated by a scanning electron microscope (SEM) technique.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.28-28
• /
• 2010

This study realized low-temperature crystallization process of the $Ba_{0.6}Sr_{0.4}TiO_3$ (BST) thin films without thermal damage of substrate using excimer laser annealing (ELA) and structural and electrical characteristics were investigated. The amorphous BST thin films were prepared on Pt/Ti/$SiO_2$/Si substrate by sol-gel method at $250^{\circ}C$. The ELA was carried out using KrF excimer laser which provided excitation wavelength of 248 nm. The beam homogenizing system was used in order to homogenize beam shape of Gaussian fit. The XRD and SEM were used to analyze structural characteristics and the microwave capacitance, dielectric loss and tunability of the BST films were measured by a symmetrical stripline resonator method with shorted end. Consequently, the crystallinity of BST thin films were improved after ELA process and RF tunable capacitor was demonstrated at low temperature below $300^{\circ}C$.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.4
• /
• pp.76-83
• /
• 1985

Mo2N/Mo double layer which is to be used for gate of the RMOS (refractory metal oxide semiconductor) and interconnection material has been formed by means of low temperature r.f. reactive sputtering in Ar and N2 mixture. The sheet .esistance of 1 000$\AA$Mo2 N/4000$\AA$Mofilm was about 1.20-1.28 ohms/square, which is about an order of magnitude lower than that of polysilicon film. The workfunction difference naE between MO2N/MO layer and (100) p-Si with 6-9 ohm'cm resistivity obtained from C-V plots was about -0.30ev, and the fixed charge density Qss/q in the oxide was about 2. Ix1011/cm2. To evaluate the signal transfer delay time per inverter stage, an integrated ring oscillator circuit consisting of 45-stage inverters was fabricated using the polysilicon gate NMOS process. The signal transfer delay time per inverter stage obtained in this experiment was about 0.8 nsec

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.1
• /
• pp.49-53
• /
• 2011

Diamond-like carbon (DLC) films is a metastable form of amorphous carbon containing a significant fraction of Sp3 bond. DLC films have been characterized by a range of attractive mechanical, chemical, tribological, as well as optical and electrical properties. In this study DLC films were prepared by the RF magnetron sputter system on $SiO_2$ substrates using graphite target. The effects of the post annealing temperature on the Property variation of the DLC films were examined. The DLC films were annealed at temperatures ranging from 300 to $500^{\circ}C$ using rapid thermal process equipment in vacuum. The variation of electrical property and surface morphology as a function of annealing treatment was investigated by using a Hall Effect measurement and atomic force microscopy. Raman and X-ray photoelectron spectroscopy analyses revealed a structural change in the DLC films.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.239-244
• /
• 2019

Two hydrogenation surface modifications, namely hydrogen atmosphere heat treatment and hydrogen plasma treatment, were found to lead to improved dispersion of nanodiamond (ND) seed particles and enhanced nucleation density for deposition of smooth ultrananocrystalline diamond (UNCD) film. After hydrogenation, the C-O and O-H surface functionalities on the surface of nanodiamond particles were converted to the C-H surface functionalities, and the Zeta potential was increased. As the degree of dispersion was improved, the size of nanodiamond aggregates decreased significantly and nucleation density increased dramatically. After hydrogen heat treatment at 600℃, average size of ND particles was greatly reduced from 3.5 ㎛ to 34.5 nm and a very high nucleation of ~3.9 × 10¹¹ nuclei/㎠ was obtained for the seeded Si surface.