• 한국표면공학회지
• /
• 제34권6호
• /
• pp.575-584
• /
• 2001

Erosion due to abrasive particles contained in gas streams from boilers has been emerged as a significant problem in the coal fired power plants. Particle erosion accounted for approximately 50% of boiler failures and especially flyash erosion was responsible for 20~30% of emergency boiler shutdowns. Particularly, because of the high ash loading and high velocity, most erosion occurs in the boiler tubes and economiser tube bank where the direction of the gas stream changes to $180^{\circ}$ .In this study, a high temperature particle erosion tester was used to evaluate erosion rate in a simulated environment. The erosion parameters such as erosion temperature, particle impact angle, particle velocity and various particle size were changed. Flyash is the combustion product of the pulverized coal, where size is ranging from 1 to $200\mu\textrm{m}$. Flyash composed of mainly SiO$_2$, $A1_2$$_O3$, and $Fe_2$$O_3$has dense spherical particles and irregular particles containing numerous pores and cavities. From the erosion tests at various conditions, the maximum erosion was experienced at impact angles of $30^{\circ}$ to $60^{\circ}$ In addition, erosion rate increased in proportional to velocity and temperature. And from the observation of the eroded surfaces, it was also concluded that 304 stainless steel was mainly eroded by extrusion-forging at high impact angle ($90^{\circ}$) and by microcutting mechanism at low impact angles ($30^{\circ}$ and $45^{\circ}$).

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.173-177
• /
• 2013

The purpose of this paper is to investigate the influences on mechanical properties of two-stroke cycle motor pistons manufactured by casting, conventional forging and powder forging, through the comparison of characteristics, merits and disadvantages of each forming technology. For each forming technology, the optimal process parameters were determined through the experiments for several conditions, and microstructure, hardness, tensile strength and elongation of pistons are compared and analyzed. In conventional forging process, material temperature was $460^{\circ}C$ and the die temperature was $210^{\circ}C$ for the Al 4032. The optimal condition was found as solution treatment under $520^{\circ}C$ for 5 hours, quenching with $23^{\circ}C$ water, and aging under $190^{\circ}C$ for 5 hours. In powder forging process, the proper composition of material was determined and optimal sintering conditions were examined. From the experiment, 1.5% of Si contents on the total weight, $580^{\circ}C$ of sintering temperature, and 25 minutes of sintering time were determined as the optimal process condition. For the optimal condition, the pistons had 76.4~78.3 [HRB] of hardness, and 500 [MPa] of tensile strength after T6 heat treatment.

• 열처리공학회지
• /
• 제8권3호
• /
• pp.229-235
• /
• 1995

We were studied to the effect of alloying element and retained austenite on a mechnical properties and that used steels were composed three types composition. According to the soaking temperature, a retained austenite was pricipitated in the bainitic ferrite matrix and it was pricipitated to a flake type of about $2{\mu}m$, a mixture of massive and bar type and a flake type of about $1{\mu}m$ size. Through x-ray diffraction analysis, the amount of retained austenite was increased with addition of Si and Ni for equal heat treatment condition and it was best abundanted in the soaking temperature of $855^{\circ}C$. The balance value of strength and elongation were complexly controlled not only a retained austenite formation but also a formation characteristic and shape of the retained austenite and bainite. The balance value of strength and elongation were most satisfactory obtained with "B" and "C" specimens in a firstly heat treated at $855^{\circ}C$ and the best result was that a $2840kg/mm^2.%$ with the heat teratment condition of $855^{\circ}C-400^{\circ}C$ used for "C" specimen.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1530-1531
• /
• 2011

$SiO_2$ 상압 증착을 위해서 Dielectric-Barrier Diacharge를 이용한 대기압 플라즈마 Jet 상압 증착 시스템을 개발하였으며, 제작된 플라즈마에 대한 전기-광학적 특성을 분석하였다. 플라즈마 Jet은 방전 구동 gas와 증착을 위한 혹합 gas가 나오는 stainless-steel관과 유리관 그리고 외부전극으로 구성되어있다. 구동 주파수는 수십 kHz대 이고 인가전압은 1~2 $kV_{rms}$이다. 본 연구에서는 ICCD 고속 카메라를 이용하여 플라즈마의 형상을 관찰하였고, OES 분석을 통해 radical들의 분석과 rotational temperature 측정을 하였다. Driving gas인 He은 1~5 SLM의 유속으로 흘려주었으며 발생된 플라즈마의 온도는 조건에 따라서 400~850 K 이다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.129-139
• /
• 2005

In this paper, the behaviors of tunnel damaged by fire, the diagnostic techniques for evaluating tunnel stability are presented. Also two fireproof construction methods are recommended. Three tunnels damaged by fire were analyzed to evaluate the structural stability. From the these analyzed, it is recommended that surface checking, rebound number of concrete by Schmidt Hammer, and carbonation of concrete are essential to evaluate the engineering properties of concrete in tunnel structure damaged by fire. On the basis of case studies of tunnel fire collected by ITA, the change of concrete and steel strengths by fire are explained, and numerical analysis, which was performed on culvert and circle tunnel, shows that distribution of temperature in the tunnel is dependant upon tunnel shape. Two fireproof construction methods using panel and punching metal are introduced to protect the tunnel by fire.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.351-359
• /
• 2006

Ni based($Ni_{57}Zr_{20}Ti_{18}Si_2Sn_3$) bulk metallic glass(BMG) powders were produced by a gas atomization process, and ductile Cu powders were mixed using a spray drying process. The Ni-based amorphous powder and Cu mixed Ni composite powders were compacted by a spark plasma sintering (SPS) processes into cylindrical shape. The relative density varied with the used SPS mold materials such as graphite, hardened steel and WC-Co hard metal. The relative density increased from 87% to 98% when the sintering temperature increased up to $460^{\circ}C$ in the WC-Co hard metal mold.

• 지질공학
• /
• 제25권1호
• /
• pp.1-8
• /
• 2015

Deep geological disposal is the preferred storage method for high-level radioactive waste, because it ensures stable long-term storage with minimal potential for human disruption. Because of the risk of groundwater contamination, a buffer of steel and bentonite layers has been proposed to prevent the leaching of radionuclides into groundwater. Quartz is one of the most common minerals in earth's crust. To understand how deformation and dissolution phenomena affect waste disposal, here we study quartz samples at pressure, temperature, and pH conditions typical of deep geological disposal sites. We perform a dissolution experiment for single quartz crystals under different pressure and temperature conditions. Solution samples are collected and the dissolution rate is calculated by analyzing Si concentrations in a solution excited by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). After completing the dissolution experiment, deformation of the quartz sample surfaces is investigated with a confocal laser scanning microscope (CLSM). An empirical formula is introduced that describes the relationship between dissolution rate, pressure, and temperature. These results suggest that bentonite layers in engineering barrier systems may be vulnerable to thermal deformation, even when exposed to higher temperatures on relatively short timescales.

• 한국분말재료학회지
• /
• 제3권4호
• /
• pp.227-232
• /
• 1996

(i) The development of a metallurgical bond during the spray forming of clad products has offered the possibility of manufacturing large rolls, including those used in hot and cold strip mills. Small rolls are already being produced in Japan. (ii) Technical developments, including the use-of-multi-atomizers have resulted in the elimination of porosity from the internal bore of a sprayed tube. Bimetallic tubing can also be manufactured and the installation of a 4.5 ton tube plant in the USA should provide low operation costs. (iii) Spray forming offers a potentially low cost manufacturing route for superalloy ring/casing components in high strength superalloys. (iv) A large pilot plant has been built for the spray forming of ultra-clean superalloys for turbine disc applications. (v) Using twin-atomizing technology, special steel billets have been spray formed up to 400mm diameter with deposition yields in excess of 90%. (vi) Al/Si alloy extrusion billets with excellent dimensional tolerances are being manufactured for large scale automotive applications. Several new aluminum alloys have also been developed, including high strength, low density and low cocfficient of expansion materials. (vii) New copper alloys have been developed and pilot plants are in operation to produce these alloys once markets have become established.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.25-29
• /
• 2004

Some industrial steel structures are composed by components linked by several welding joints to constitute an assembly. The main interest of assembly simulation is to evaluate the global distortion of welded structure. The general method, thermo-elasto-plastic analysis, leads to excessive model size and computation time. In this study, a simplified method called "Local and Global approach" was developed to break down this limit and to provide a accurate solution for distortion. Local and global approach is composed of 3 steps; 1) Local simulation of each welding joint on a dedicated mesh (usually very fine due to high thermal gradients), taking into account for the non linearity of the material properties and the moving heat source. 2) Transfer to the global model of the effects of the welding joints by projection of the plastic strain tensors. 3) Elastic simulation to determine final distortions in global model. The welding deformation test for mock-up structure was performed to verify this approach. The predicted welding distortion by this approach had a good agreement with experiment results.

• KIEAE Journal
• /
• 제9권2호
• /
• pp.73-80
• /
• 2009

In the early twentieth century, many architects still practised eclectic design elements. Emergence of new building materials such as steel, concrete and glass were not yet found fresh roles in architectural design. It was Brussels that the use of modern materials gave rise to their new forms and gave influence to not only building skins but also spatial organization. Art Nouveau architecture is often seen as revolutionary and pioneering modern architecture against eclectic classicism prevalent in the 18th and 19th centuries. Despite the fact that some scholars point out that Art Nouveau is more a transient phenomenon than modern architecture proper, no one would deny that Art Nouveau carries a good deal of modern characteristics. This paper intends to show rather ambivalent perspectives upon Art Nouveau architecture. Although it insinuates overly dynamic nature in architectural languages, it does not hamper us from reading Art Nouveau as a vital component of modern architecture. Through a careful analysis of the early domestic designs of Victor Horta, it becomes evident that his work can provide modern architecture a meaningful alibi for its growth. Victor Horta's house design is well known to the public, both for his classical tastes and for its changing implementation. Horta's modern quality is never adequately recognized, partly due to his eye catching modern iron properties and sinuous ornamentation. This paper tries to offer an insight into the complicated stage set of the fin-de-$si{\grave{e}}cle$ through the work of Victor Horta whose influence has been immense in the making of modern architecture.