• 한국재료학회지
• /
• 제31권5호
• /
• pp.301-311
• /
• 2021

The conversion of all carbon preforms to dense SiC by liquid infiltration can become a low-cost and reliable method to form SiC-Si composites of complex shape and high density. Reactive sintered silicon carbide (RBSC) is prepared by covering Si powder on top of 0.5-5.0 wt% Y₂O₃-added carbon preforms at 1,450 and 1,500℃ for 2 hours; samples are analyzed to determine densification. Reactive sintering from the Y₂O₃-free carbon preform causes Si to be pushed to one side and cracking defects occur. However, when prepared from the Y₂O₃-added carbon preform, an SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C = SiC reaction, 3C and 6H of SiC, crystalline Si, and Y₂O₃ phases are detected by XRD analysis without the appearance of graphite. As the content of Y₂O₃ in the carbon preform increases, the prepared RBSC accelerates the SiC conversion reaction, increasing the density and decreasing the pores, resulting in densification. The dense RBSC obtained by reaction sintering at 1,500 ℃ for 2 hours from a carbon preform with 2.0 wt% Y₂O₃ added has 0.20 % apparent porosity and 96.9 % relative density.

• 한국분말재료학회지
• /
• 제28권1호
• /
• pp.51-58
• /
• 2021

The conversion of carbon preforms to dense SiC by liquid infiltration is a prospectively low-cost and reliable method of forming SiC-Si composites with complex shapes and high densities. Si powder was coated on top of a 2.0wt.% Y2O3-added carbon preform, and reaction bonded silicon carbide (RBSC) was prepared by infiltrating molten Si at 1,450℃ for 1-8 h. Reactive sintering of the Y2O3-free carbon preform caused Si to be pushed to one side, thereby forming cracking defects. However, when prepared from the Y2O3-added carbon preform, a SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C → SiC reaction at 1,450℃, 3C and 6H SiC phases, crystalline Si, and Y2O3 were generated based on XRD analysis, without the appearance of graphite. The RBSC prepared from the Y2O3-added carbon preform was densified by increasing the density and decreasing the porosity as the holding time increased at 1,450℃. Dense RBSC, which was reaction sintered at 1,450℃ for 4 h from the 2.0wt.% Y2O3-added carbon preform, had an apparent porosity of 0.11% and a relative density of 96.8%.

• 청정기술
• /
• 제22권4호
• /
• pp.308-315
• /
• 2016

수명특성이 우수한 실리콘 음극재를 제조하기 위해 졸겔법을 통해 $SiO_x/ZnO$ 복합체를 제조하였고, 제조된 복합체는 PVC를 탄소 전구체로 하여 탄소를 피복하였다. 복합체에 포함된 ZnO를 HCl로 제거하여 내부에 빈 공간을 만들어 충 방전에 따른 실리콘의 부피변화를 완화할 수 있게 하였다. 합성된 복합체의 결정구조와 형상을 파악하기 위해 XRD, SEM, TEM 분석을 실시하였다. 탄소 피복된 복합체에 포함된 탄소함량을 TGA를 통해 알아보았으며, 복합체의 기공구조를 확인하기 위해 BET 비표면적 분석과 BJH 기공분포를 확인하였다. 탄소의 추가로 향상된 전기전도성을 측정하였으며, 전기화학적 특성은 AC 임피던스 측정과 충 방전 및 수명특성을 확인하였다. $SiO_x/ZnO$시료에 탄소를 피복할 경우에 전기전도도가 증가하였으며, 방전용량도 증가하였다. 염산으로 ZnO를 제거한 시료의 경우에 표면적은 증가하였으나, 전지의 방전용량은 오히려 감소하였다. 탄소를 피복하지 않은 $SiO_x/ZnO$ 시료의 경우에 방전용량이 매우 낮았으며, 탄소를 피복한 후의 시료는 높은 충방전용량을 나타내었다. 수명특성의 경우, $C-SiO_x/ZnO$ 복합체(Zn : Si : C = 1 : 1 : 8)가 0.2 C의 전류량에서 50 사이클에서 $815mAh\;g^{-1}$의 용량으로 기존 흑연계 음극재보다 높은 용량을 나타내었다.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.483-491
• /
• 2018

Effects of additives on phase development and physico-mechanical properties of mullite-carbon was investigated. Powdered clay, kaolinite and graphite of predetermined compositions were blended with additives using ball mill for 3 hrs at 60 rev/min. Samples were produced by uniaxial compression and sintered between $1400^{\circ}C$ and $1600^{\circ}C$ for one hr. They were characterized for various properties, developed phases and microstructural features. It was observed that the properties and phase developments in the samples were influenced by the additives. 10 wt % SiC served as nucleating point for SiC around $1400^{\circ}C$. 10wt % $TiO_2$ lead to development of 2.5 wt % TiC at $1500^{\circ}C$ which increased to 6.8 wt % at $1600^{\circ}C$. Ifon clay in the sample leads to development of anorthite and microcline in the samples. 10wt % $TiO_2$ is effective as anti-oxidant for graphite up to $1500^{\circ}C$. Base on strength and absorbed energy, sample C (with 10wt % $TiO_2$) sintered at $1500^{\circ}C$ is considered to be optimum.

• Korean Chemical Engineering Research
• /
• 제51권4호
• /
• pp.411-417
• /
• 2013

리튬 2차전지 음전극 활물질로 사용하기 위해, 실리콘(Si) 나노입자(평균입경 100 nm, 0~50 wt%)와 흑연 분말(평균입경 $15{\mu}m$)을 사용하여 볼밀링법으로 흑연-실리콘 복합체 분말을 제조하고 그 전기화학적 특성을 조사하였다. 실리콘 함량이 증가할수록 흑연은 볼밀링에 의해 입경이 작아지고 무정형 특성을 보이는 반면, 실리콘 입자는 나노결정성의 변화 없이 무정형 흑연 내에 싸여진 형태로 유지되었다. 저속 사이클릭 볼타메트리 특성상 0.2~0.35 V와 0.55~0.6 V에서 각각 흑연과 실리콘의 전형적 산화피크가 검출되었고 가역성도 우수(첫 사이클 제외)한 반면, 고속 거동에서는 사이클 반복에 따른 비가역성이 현저하게 나타났다. 또한 충방전 초기에는 큰 비가역 용량이 나타나지만 사이클 경과에 따라 감소하였으며, 특히 실리콘을 20 wt% 정도 포함하는 복합체가 50 사이클에서 약 485 mAh $g^{-1}$의 포화된 방전용량을 나타내었다. 이것은 실리콘을 싸고 있는 흑연의 무정형 상이 실리콘-리튬의 합금/탈합금에 따른 체적 변화를 안정적으로 완충할 수 있는 모폴로지가 재료의 적정 조성(흑연:실리콘=8:2 w/w)에 의해 형성되었기 때문이다.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.15-22
• /
• 2017

Because the running speed of vehicles is increasing and a shorter braking distance is required, high heat-resistant brake pads are needed to satisfy the requirements of customers and car makers. In the near future, hazardous materials such as Cu, Cr, Zn, and Sb will be restricted from use in friction materials. Ceramic composites reinforced by carbon fibers are good candidates for eco-friendly friction materials. In this study, we develop ceramic composite friction materials. The friction materials are composed of carbon fibers, Si, SiC, graphite, and phenol resin and are prepared by hot forming and heat treatment at high temperatures. The density, void ratio, and compressive strength are $1.59-1.66g/cm^3$, 16.6-20, and 70-90 MPa, respectively. Friction and wear tests are performed using a pin-on-plate-type reciprocating friction tester at 25, 100, and $200^{\circ}C$. The counterpart material is a CrMoV steel extracted from a KTX brake disc. Friction coefficient, wear amount, and wear mechanism are measured and examined. We determine that the friction coefficients depend on the temperature and the fluctuation of the friction coefficients is larger at higher temperatures. The amount of wear increases with the surface temperatures of the specimens. The tribological properties of the developed composites are similar to those of a Cu-based sintered friction material. Through this study, it is confirmed that ceramic composite materials can be used as friction materials.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.351-359
• /
• 2006

Ni based($Ni_{57}Zr_{20}Ti_{18}Si_2Sn_3$) bulk metallic glass(BMG) powders were produced by a gas atomization process, and ductile Cu powders were mixed using a spray drying process. The Ni-based amorphous powder and Cu mixed Ni composite powders were compacted by a spark plasma sintering (SPS) processes into cylindrical shape. The relative density varied with the used SPS mold materials such as graphite, hardened steel and WC-Co hard metal. The relative density increased from 87% to 98% when the sintering temperature increased up to $460^{\circ}C$ in the WC-Co hard metal mold.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.936-936
• /
• 2006

Bulk amorphous materials have been intensively studied to apply for various advanced industry fields due to their high mechanical, chemical and electrical properties. These materials have been produced by several techniques such as mechanical alloying, melt spinning and gas atomization, etc. Among them, the atomization is the most potential technique for commercialization due to high cooling rate during solidification of the melt and mass productivity. However, the amorphous powders still have some limitations because of their low ductility and toughness. Therefore, intensive efforts have to be carried out to increase the ductility and toughness. In this study, the Ni-based amorphous powder was produced by the gas atomization process. And in order to increase the ductile toughness, ductile Cu phase was coated on the Ni amorphous powder by spray drying process. The characteristics of the as-synthesis powders have been examined and briefly mentioned. The master alloy with $Ni_{57}Zr_{20}Ti_{16}Si_2Sn_3$ was prepared by vacuum induction melting furnace with graphite crucible and mold. The atomization was conducted at $1450^{\circ}C$ under the vacuum of $10^{-2}$ torr. The gas pressure during atomization was varied from 35 to 50 bars. After making the Ni amorphous powders, the spray drying was processed to produce the Cu -coated Ni amorphous composite powder. The amorphous powder and Cu nitrate solution were mixed together with a small amount of binder and then it was sprayed at temperature of $130^{\circ}C$ and rotating speed of 15,000 R.P.M.