• 조명전기설비학회논문지
• /
• 제23권1호
• /
• pp.85-91
• /
• 2009

본 논문에서는 배전계통에 사용되는 케이블 권선형 변압기에 전력계통에서 발생되는 서지나 고장전류에 의해서 변압기의 고압측 코일에 유도되는 전자력의 크기를 유한요소 전자계해석 프로그램(FLUX2D)을 이용하여 해석하고, 기계진동방정식을 이용하여 케이블형 권선의 고유진동주파수를 분석하였다. 변압기모델로서 1(MVA), 22,900/220([V]) 단상 외철형 Cable형을 선정하여, 권선의 각방향의 전자력을 분석하고, 고유진동 mode를 Transfer Matrix Method를 이용하여 계산하고 상용 프로그램(ANSYS)을 이용하여 분석한 결과와 비교하였다. 진동모드의 분석한 결과 제시한 수치해석 방법은 공학적인 오차범위 안에서 충분히 수용할 정도의 정확도를 보여주었다. 변압기 권선의 전자력과 진동모드 분석결과는 변압기의 절연설계 및 단락기계력에 의한 절연 구조 설계를 위한 유용한 자료로 활용될 수 있다.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.152-160
• /
• 1999

The weld quality of $CO_2$ arc welding is closely related to the arc stability. As the characteristics of the arc are excessively complex and nonlinear, it is not easy to make the arc model as mathematical form and to control the arc state to be stabilized. This paper was aimed to estimate the arc stability and to control for stabilizing the arc state in short circuit metal transfer mode of $CO_2$ arc welding. For these purposes, the behaviors of arc stability was investigated at different welding conditions using Mita's arc stability index, and the fuzzy control algorithm which uses the arc stability index as control imput and the arc voltage as control output was developed. In the control of the arc stability, the experiments of two cases were performed; the case of setting an initial welding voltage arbitrarily, the case of the step change in workpiece shape. Obtained results were as follows; Mita's arc stability index was able to be estimated qualitatively in the case of using the inverter type welding power source and the control performance for stabilizing the arc status was excellent in the case of existing step change disturbance.

• Journal of Power Electronics
• /
• 제13권1호
• /
• pp.51-58
• /
• 2013

This paper proposes the power conversion mechanism of a bailer-charge-transfer zero-current-switching (CT-ZCS) circuit. The operation modes are analyzed and researched using state trajectory equations. The topology of CT-ZCS based on soft-switching inverters offers some merits such as: tracking the input reference signal dynamically, bearing load shock and short circuit, multiplying inverter N+1 redundancy parallel, coordinating power balance for easy control, and soft-switching commutation for high efficiency and large capacity. These advantages are distinctive from conventional inverter topologies and are especially demanded in AC drives: new energy generation and grid, distributed generation systems, switching power amplifier, active power filter, and reactive power compensation and so on. Prototype is manufactured and experiment results show the feasibility and dynamic voltage-tracking characteristics of the topology.

• 한국표면공학회지
• /
• 제49권2호
• /
• pp.186-190
• /
• 2016

In this study, we fabricated the transparent photovoltaic device using 2-dimensional transition-metal dichalcogenides and investigated the transparency and photovoltaic characteristics. P-n heterojunction was formed by mechanical exfoliation and aligned transfer method on the transparent sheet using n-type $MoS_2$ and p-type $WSe_2$. Our transparent photovoltaic device exhibited the open-circuit voltage of ~ 0.15 V and the short-circuit current of 0.48 nA under illumination of white light.

• Journal of Welding and Joining
• /
• 제25권5호
• /
• pp.58-63
• /
• 2007

The relationship between GMA welding conditions and the bead shape of overlay weld was studied by using ${\Phi}1.6mm$ hypo-eutectic metal-cored wire designed for hardfacing against the severe metal-to-metal wear. As the welding voltage increased, the dilution also increased but the sudden drop of dilution was observed at $30{\sim}33V$. It was considered to be due to the decrease of penetration resulting from the change of transfer mode, from short circuit to spray. It was also found that the behavior of penetration with welding current was dependant on the transfer mode. The short circuit mode exerted the penetration to decrease while the spray mode did it to increase with increase of welding current. The former was considered to be responsible for the remarkable decrease in dilution at low welding voltage region. The change of transfer mode also had an effect on the behavior of bead width with welding current but it did not on the bead spreadability defined as W/H ratio. It was considered that the optimal welding conditions for multi-pass overlay welding could be obtained from the bead spreadability suitable for bead lapping and the dilution as low as possible in the spray transfer mode.

• 한국추진공학회지
• /
• 제24권6호
• /
• pp.28-44
• /
• 2020

본 연구에서는 무인 항공기용 소형 2행정 엔진의 성능 개선을 위해 다양한 전송 포트 형상의 가스교환 성능을 평가하였다. 성능 평가를 위해 네 가지 전송 포트 형상에 따른 3차원 전산 유체 해석을 진행하였으며, 가스 교환 성능의 정량적 평가를 위해 이상적 소기 모델인 완전 대체 소기 모델과 완전 혼합 소기 모델을 바탕으로 새로운 3단계 소기 모델을 개발하여 해석 결과에 적용하였다. 2행정 엔진의 전송 포트 형상 변경을 통해 흡기의 단락 현상을 효과적으로 줄였으며 가스 교환 과정 동안의 실린더 내 난류 에너지 또한 크게 개선되었다. 또한, 전송 포트 형상 별 3단계 소기 모델의 적용을 통해 가스 교환 성능을 정량적으로 평가할 수 있었으며, 포트 형상 별 소기 양상의 차이를 확인할 수 있었다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권5호
• /
• pp.257-263
• /
• 1999

Recently the performance of CO2 arc welding machine has been advanced significantly through the adoption of inverter circuit topology which made it possible to control the waveform of welding current and thus to suppress the spatter generation. However, the optimum waveform is still uncertain. As a first step for figuring out the promising waveforms, this study was performed to set-up the experimental system for studying the effect of waveform variables, The system designed in this study is a digital controller using single chip microprocessor of 80C196KC. As a result of performance test of this system, it was demonstrated all of the waveform variables could be set individually and the resultant waveforms appeared to be pretty much the same as the intended one.

• 전력전자학회논문지
• /
• 제7권3호
• /
• pp.272-280
• /
• 2002

$CO_2$ GMAW의 연구동향은 주로 용접시에 발생하는 스패터의 저감에 초점이 맞추어져 있으며 이들은 크게 용접 재료의 개선 또는 용접전원의 개선으로 크게 분류될 수 있다. 용접재료 측면에서는 새로운 전극의 재질이나 차폐가스등 새로운 물질에 대한 연구 분야가 있으며 용접전원 측면에서는 아크상태를 최적으로 제어할 수 있는 회로구조 및 제어기법에 대한 연구이다. 본 논문에서는 PWM 인버터형 $CO_2$ GMAW의 금속이행과 및 용접을 위한 여러 제어기법에 대하여 기술하였다. 또한 단락이행시 및 아크재발생시의 제어에 의한 스패터의 저감 방법을 제시하였으며 여러 제어방식과 스패터 저감특성을 비교 연구하였다.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.85-102
• /
• 1995

Weld quality of GMA welding processes is closely related to arc stability. Although many researches on arc stability have been performed, real-time estimation of arc stability has not been attempted. For instance, Mita proposed a off-line statistical method in which short circuiting and arcing time, and voltage and current wave forms were sampled to assess arc stability. But this method is not suitable to assess arc stability for GMA welder which employ inverter power source due to its controlled current and voltage wave forms. In this paper, the relationship between are stability and wire feed rate fluctuation is analyzed to propose new criterion for inverter power source. When arc voltage and arc current and arcing time are analyzed, we can assess arc stability only for short circuit transfer mode. When wire feed rate is analyzed, we can estimate arc stability udner the condition of spray transfer mode as well. Hence, the wire feed rate is chosen for monitoring process variable to cover possible metal transfer modes in GMAW. Through this research, it has been identified that arc stability in GMA welding processes is closely related to wire fed rate. When inverter power source is used, conventional statistical method of estimating arc stability, such as Mita index, is no longer valid due to its controlled voltage and current wave forms. Arc stability has been also examined in phase plane diagram.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.171-173
• /
• 2004

Electromagnetic force is one of the most important factor that effect on metal transfer mode, short-circuit rate, spatter generation rate and mechanical properties of weld metal etc. Also, shielding gas and welding current have influence on metal transfer mode in GMAW. In this paper, different ways for external electromagnetic forces are applied by attaching cylindrically rounded conducting wire solenoid on touch tip holding. With the applied electromagnetic field, the arc transfer mode changes from normal mode to rotating mode and spatter generation decreased in electromagnetic fields(N-pole). In MIG welding, the influences of electromagnetic force on the spatter generation showed different tendency as in the $CO_2$ welding. It is possible reasons were discussed.