• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.26-32
• /
• 2012

This study has been performed Thermal Shock test for analyze the cause of Power drop in PV(Photovoltaic) Module. Thermal Shock test condition was performed with temperature range from $-40^{\circ}C{\sim}85^{\circ}C$. One cycle time is 30min. which are consist of low and high temperature 15min. each other. The test was performed with total 500cycles. EL, I-V were conducted every 100cycle up to 500cycles. Mono Cell resulted in 8% Power drop rates in Bare Cell and 9% in Solar Cell. In the case of Multi Cell resulted in 6% Power drop rates in Bare Cell and 13% in Solar Cell. After Thermal Shock test, Solar Cell's Power drop resulted from surface damages, but in the case of Bare Cell's Power drop had no surface damages. Therefore, Bare Cell's Power drop was confirmed as according to leakage current increase by analysis of Fill Factor after Thermal Shock test. Also, Solar Cell's Power drop rates are higher than that of Bare Cell because of surface damages and consuming electric power increase. From now on, it should be considered that analyzed the reasons of Fill Factor decrease and irregular Power drop in PV module and Cell level using cross section, various conditions and test methods.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.11 no.1
• /
• pp.17-24
• /
• 2005

During handling unitized products, they are subjected to a variety environmental hazards. Shock and vibration hazards are generally considered the most damaging of the environmental hazards on a product, and it may encounter while passing through the distribution environment. A major cause of shock damage to products is drops during manual handling. The increasing use of unitization on pallets has been resulted in a reduction in the manual handling of products and with it a reduction in the shock hazards. This has caused and increasing interest in research focused on vibration caused damage. the use of pallets as a base for unitizing loads, aids in the mechanical handling, transportation and storage of products. Besides aiding in the handling, transportation and storage of products, a pallet also acts on and interface between the packaged goods and the distribution environment. The determination of the impact deformation of the cushioning materials such as tray cup (polymeric foam) and corrugated fiberboard pad must be carried out to design the proper packaging system providing adequate protection for the fruit, and to understand the complex interaction between the components of fruit when they relate to expected transportation vibration inputs. In this study, the theoretical analysis of impact deformation for cushioning materials by dynamic vibration. The impact deformations of SW and DW corrugated fiberboard pad in acceleration amplitudes of 0.25 G-rms and 0.5 G-rms that were usually generated in transport vehicles during distribution environments were very small compare with the thickness of corrugated fiberboard pad. The maximum of vibration acceleration level of tray cup by vibration impact was about 3.2 G-rms. The theoretical allowable acceleration (G-factor) of the pear was 0.7102 G-rms, and the maximum dynamic deformation estimated within G-factor was about 1 mm.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.91-98
• /
• 1992

In the research on the fracture time of soda lime silicate glass under thermal shock, it is shown that the theoretical and experimental fracture times are in good agreement, the suggested method to measure critical stress intensity factor for small three-point bending specimen is useful and the edge temperature before thermal shock on cracked side vs. crack length and fracture time are inversely proportional.

• Journal of The Korean Astronomical Society
• /
• v.17 no.2
• /
• pp.115-125
• /
• 1984

Effect of magnetic field on the thermal instability is studied in the radiatively cooling region behind an interstellar shock of moderate propagation velocity (${\sim}10\;km/sec$). It is shown that the presence of interstellar magnetic field of a few micro gauss is very effective in preventing the thermal instability from building-up density concentration. In the absence of magnetic field, the shock-induced thermal instability amplifies preshock density inhomogeneity by more than an order of magnitude. However, in the presence of magnetic field, the amplified density contrast is shown to be only a factor 2.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.463-474
• /
• 1995

Modified Vainshtok weight function method is developed. The thermal shock stress intensity factors for elliptical surface cracks existed in the thin and thick walled cylinders are determined. The present results are compared with previous solutions and shown to be good agreement with them.

• Journal of The Korean Society of Clinical Toxicology
• /
• v.8 no.1
• /
• pp.30-36
• /
• 2010

Purpose: The purpose of this study is to analyze the clinical characteristics of anaphylaxis and anaphylactic shock caused by bee venom. Methods: We retrospectively collected the data of the patients who experienced anaphylaxis caused by natural bee sting or acupuncture using bee venom from January 1999 to December 2008. Seventy subjects were divided into the shock and non-shock groups. The clinical characteristics, sources of bee venom, treatments and outcomes were compared between the two groups. Results: The mean age of the subjects was $45.5{\pm}16.3$ years old and the number of males was 44 (62.9%). There were 25 patients in the shock group and 45 in the non-shock group. The age was older (p=0.001) and females (p=0.003) were more frequent in the shock group. Transportation to the hospital via ambulance was more frequent in the shock group (p<0.001). No difference was found in species of bee between the two groups. The cephalic area, including the face, was the most common area of bee venom in both groups. Anaphylaxis caused by bee sting commonly occurred between July and October. Cutaneous and respiratory symptoms were the most frequent symptoms related to anaphylaxis. Cardiovascular and neurologic symptoms were more frequent in the shock group. The amount of intravenously administered fluid and subcutaneous injection of epinephrine were much more in the shock group than that in the non-shock group. Conclusion: Older age was the factors related to anaphylactic shock caused by bee venom. Further validation is needed to evaluate the gender factor associated with shock.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.12
• /
• pp.1347-1353
• /
• 2004

With respect to the researches of the optical flying head(OFH) , the head-gimbal assembly should be analyzed to guarantee the stable fabrication and the characteristics of shock resistance. The suitable design is proved through the Probabilistic analysis of the design parameters and material properties of the model. Probabilistic analysis is a technique that be used to assess the effect of uncertain input parameters and assumptions on your analysis model. Using a probabilistic analysis you can find out how much the results of a finite elements analysis are affected by uncertainties in the model. Another factor is analysis of the dynamic shock analysis. For the mobile application, one of the important requirements is durability under severe environmental condition, especially, resistance to mechanical shock. An important challenge in the disk recording is to improve disk drive robustness in shock environments. If the system comes in contact with outer shock disturbance. the system gets critical damage in head-gimbal assembly or disk. This paper describes probabilistic and dynamic shock analysis of head-gimbal assembly in micro MO drives using OFH slider.

• Nuclear Engineering and Technology
• /
• v.33 no.2
• /
• pp.132-144
• /
• 2001

Fracture mechanics is one of the major areas of the pressurized thermal shock (PTS) evaluation. To evaluate the reactor pressure vessel integrity associated with PTS, PFM methodology demands precise calculation of temperature, stress, and stress intensity factor for the variety of PTS transients. However, the existence of stainless steel cladding, with different thermal, physical, and mechanical property, at the inner surface of reactor pressure vessel complicates the fracture mechanics analysis. In this paper, treatment schemes to evaluate stress and resulting stress intensity factor for RPV with stainless steel clad are introduced. For a reference transient, the effects of clad thermal conductivity and thermal expansion coefficients on deterministic fracture mechanics analysis are examined.

• Computational Structural Engineering
• /
• v.11 no.1
• /
• pp.153-160
• /
• 1998

A small break loss of coolant accident is postulated as a pressurized thermal shock accident in this study. From the temperature and pressure histories of coolant, distributions of the temperature and stress in a vessel wall are analytically calculated. The stress intensity factor and fracture toughness of the vessel wall are determined at the crack tip using the ASME code method and they are compared to check if cracking is expected to occur during the transient postulated. The maximum allowable reference nil-ductility transition temperatures are determined for various crack sizes and the results are discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.111-116
• /
• 2001

A practical scheme to reduce failure of the PCB(Printed Circuit Board) of a monitor is introduced using deformed mode shape under mechanical shock. When the monitor is given critical shock loads, cracks are commonly initiated at the tip of a hole on the PCB. Accordingly, a deformed mode shape of the PCB is obtained using a FEM code to define a weak point on the PCB under mechanical shock, and then the position and direction of the hole is determined to prevent the failure at the critical mode shape. Also, the stress intensity factor around the weak point on the PCB is calculated to check the possibility of fracture by normal tensile stress. In conclusion, present research is useful to assist the practical design of components-layout on the PCB.