• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.601-609
• /
• 2022

Jack-up drilling rigs are mobile offshore platforms widely used in the offshore oil and gas exploration industry. These are independent, three-legged, self-elevating units with a cantilevered drilling facility for drilling and production. A typical jack-up rig includes a triangular hull, a tower derrick, a cantilever, a jackcase, living quarters and legs which comprise three-chord, open-truss, X-braced structure with a spudcan. Generally, jack-up rigs can only operate in water depths ranging from 130m to 170m. Recently, there has been an increasing demand for jack-up rigs for operating at deeper water levels and harsher environmental conditions such as waves, currents and wind loads. All static and dynamic loads are supported through legs in the jack-up mode. The most important issue by society is to secure the safety of the leg structure against collision that causes large instantaneous impact energy. In this study, nonlinear FE -analysis and verification of the requirement against collision for 35MJ recommended by DNV was performed using LS-Dyna software. The colliding ship used a 7,500ton of shore supply vessel, and five scenarios of collisions were selected. From the results, all conditions do not satisfy the class requirement of 35MJ. The loading conditions associated with chord collision are reasonable collision energy of 15M and brace collisions are 6MJ. Therefore, it can be confirmed that the identical collision criteria by DNV need to be modified based on collision scenarios and colliding members.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.3
• /
• pp.243-249
• /
• 2023

The occurrence of cavitation on the propeller is directly linked to the naval ship's survivability, and it is necessary to design a propeller shape that delays the cavitation inception. However, the propeller cavitation can occur under various operating conditions, thus it is important to identify whether the propeller cavitation exists during operation as well as in the design phase. To this end, it is necessary to use noise or vibration signals on board to monitor the cavitation inception. In this study, a hydrophone and an accelerometer were installed on the ship hull right above the propeller to compare the performance of analyzing cavitation inception between acoustic and vibration signals. Also, a high speed camera was used to visually observe the occurrence of cavitation through an observation window. The measured results showed that the spectral shapes between acoustic and vibration signals were different, but the level increases at each frequency band and the overall level of the frequency band from 1 kHz to 10 kHz showed a similar tendency. The Detection of Envelope Modulation On Noise (DEMON) analysis also showed similar results for both acoustic and vibration signals, confirming that both hydrophones and accelerometers can be utilized in the analysis of cavitation inception.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.950-957
• /
• 2023

For safe mooring and towing between the ship and port, the equipment must be designed in accordance with the relevant international regulations. However, some small shipyards and engineering companies often do not fully comprehend the core contents. Therefore, the international regulations regarding towing and mooring equipment are reviewed and the bollard and chock are newly developed based on the Mooring Equipment Guideline 4 (MEG4) standards. A bollard is a mooring equipment used to fix a mooring rope to the hull. It has two columns and is mostly used in a figure eight pattern knots under the mooring condition. The chock, which is used to change the mooring rope direction coming into the ship from outside, is manufactured using a casting with curvature. The two mooring equipment are widely used in the stern, bow, and mid-side. Owing to the increase in the size of container vessels and LNG ships, the mooring rope load has increased and the safe working load of the mooring equipment must be revised. This study summarizes and examines the results of the allowable stress method obtained using finite element analysis modelling. To consider the mesh size effect, a reasonable criteria was suggested by referring the existing class guidance. Additionally, the safe working load was verified through nonlinear collapse analysis, and the elastic region against load increments was confirmed. Furthermore, the proposed evaluation method can be used to develop similar equipment in the near future.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.566-573
• /
• 2017

The chine of high speed vessels does not only play a role in changing position when planing but also helps balancing the hull. It also has a great influence on resistance performance. However, designing a chine requires a lot of experience because it is influenced by various factors such as displacement, transom shape, draft and width. Such a design is not based on an empirical formula, but the purpose of this study is to provide basic guidelines regarding the shape of chine through calculation. This design was developed using Yacht-one, a commercial design program, and analysis was performed using Star-CCM+, also a commercial analysis program. Analysis of the hull selected in this study was carried out by Dynamic Fluid Body Interaction (DFBI) method. Analysis of the chine was carried out at chine angles of 15, 16, 17, and 19degrees, at a speed of 30knots. The result indicated that the highest trim occurred at 16 degrees among the four chine angles considered, and the highest heave occurred at 15degree. In terms of resistance performance, minimum resistance was observed at 16 degrees. Consequently, for minimum ship resistance, it is necessary to complete calculations in accordance with the chine angles, ${\pm}2$ degrees from the initial chine angle, which should be carried out a the design stage.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.1
• /
• pp.66-74
• /
• 2018

In order to evaluate the precision degree of the blocks on the dock, the shipyards recently started to use the point cloud approaches using the 3D scanners. However, they hesitate to use it due to the limited time, cost, and elaborative effects for the post-works. Although it is somewhat traditional instead, they have still used the electro-optical wave devices which have a characteristic of having less dense point set (usually 1 point per meter) around the contact section of two blocks. This paper tried to expand the usage of point sets. Our approach can estimate the rework time to weld between the Pre-Erected(PE) Block and Erected(ER) block as well as the precision of block construction. In detail, two algorithms were applied to increase the efficiency of estimation process. The first one is K-mean clustering algorithm which is used to separate only the related contact point set from others not related with welding sections. The second one is the Concave hull algorithm which also separates the inner point of the contact section used for the delayed outfitting and stiffeners section, and constructs the concave outline of contact section as the primary objects to estimate the rework time of welding. The main purpose of this paper is that the rework cost for welding is able to be obtained easily and precisely with the defective point set. The point set on the blocks' outline are challenging to get the approximated mathematical curves, owing to the lots of orthogonal parts and lack of number of point. To solve this problems we compared the Radial based function-Multi-Layer(RBF-ML) and Akima interpolation method. Collecting the proposed methods, the paper suggested the noble point matching method for minimizing the rework time of block-welding on the dock, differently the previous approach which had paid the attention of only the degree of accuracy.

• Journal of Navigation and Port Research
• /
• v.28 no.6
• /
• pp.481-489
• /
• 2004

Ship collisions and grounding continue to occur regardless of continuous efforts to prevent such accidents. With the increasing demand for safety at sea and for protection of the environment, it is of crucial importance to be able to reduce the probability of accidents, assess their consequences and ultimately minimize or prevent potential damages to the ships and the marine environment. Numerical simulations for actual collision problem are conducted with a special attention with respect to finite element size, fracture criteria and material properties, which require a careful consideration to improve the accuracy. A parametric analysis varying colliding speed, angle, design loading condition is conducted using nonlinear finite element analysis method for 46,00 dwt Product/chemical carrier. The relationship between the absorbed energy and indentation are derived quantitatively using the insights observed from this study, and a novel design concept for assessing the anti-collision performance are proposed.

• Journal of Navigation and Port Research
• /
• v.31 no.5 s.121
• /
• pp.435-445
• /
• 2007

Ship structures are thin-walled structures and lots of cutouts, for example, of inner bottom structure, girder, upper deck hatch, floor and dia-frame etc. In the case where a plate has cutout it experiences reduced buckling and ultimate strength and at the same time the in-plane stress under compressive load produced by hull girder bending will be redistributed. In the present paper, we investigated several kinds of perforated stiffened model from actual ship structure and series of elasto-plastic large deflection analyses were performed to investigate into the influence of perforation on the buckling and ultimate strength of the perforated stiffened plate varying the cutout ratio, web height, thickness and type of cross-section by commercial FEA program(ANSYS). Closed-form formulas for predicting the ultimate strength of the perforated stiffened plate are empirically derived by curve fitting based on the Finite Element Analysis results. These formulas are used to evaluate the ultimate strength, which showed good correlation with FEM results. These results will be useful for evaluating the ultimate strength of the perforated stiffened plate in the preliminary design.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.867-874
• /
• 2021

The IoT (Internet of Things) technology is rapidly becoming an important consideration in many engineering fields in the current 4th industrial era. In recent years, the concepts of digital shipbuilding and smart factories have been adopted as trends in shipyards. However, there is active interest in research on implementing autonomous driving in autonomous vehicles and airplanes, which is currently available in commercial form in a limited capacity. The present study is regarding the path-tracking performance of a boat to accomplish an autonomous driving mission using a flight controller (FC) and real-time kinematic (RTK) global positioning system (GPS) based on an open-source Ardupilot; an actual sea test is also performed using this system on a calm lake. The boat's mission is to evaluate the maneuverability of the self-driving process to a specific point and returning to the home position. For a given speed, the difference between the preset mission trajectory and actual operational trajectory was analyzed, and a series of studies were conducted on the applicability of the system to ships. In addition, the movements and maneuverability of the OmniX-type hull with four propellers were investigated, and the driving path-tracking performance was observed to increase by a maximum of 48%.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.832-838
• /
• 2021

Recently, reports of marine accidents of small fishing vessels less than 10 tons have been increasing. In this study, the characteristics of the motion response in regular waves were analyzed using computations for these ships. Small vessels less than 10 tons are classified by size and used for marine accident investigations. Therefore, the motion response analysis was performed on three small fishing vessels of different sizes. In the case of the head sea, it was confirmed that as the speed of the vessel increased in the long wavelength region, the motion responses of heave and pitch became large. The motion response of the smallest 3-ton fishing vessel was greater than that of the other sizes of fishing vessels. The maximum value of the roll motion shifted to the long wavelength region as the speed gradually increased in the bow sea, regardless of the size of the ship. In all the three small fishing vessels, it was found that the roll motion was the greatest at 15 knots, the highest speed in both bow and beam seas. When sailing in the head sea and bow sea conditions, lowering the speed is one of the effective approaches to reduce the effects of the vertical and lateral plane motions. The roll motion caused by the beam wave showed a tendency to increase rapidly only at a specific wavelength regardless of the speed and the size of the vessel. It was confirmed that the roll motion was significantly reduced with forward speed in the stern wave compared to the bow wave. As there is a specific region where the maximum value of the hull motion response appears depending on the size and speed of the ship, an operation method that can minimize the effect of this motion should be considered and implemented.

• Journal of Korea Trade
• /
• v.25 no.2
• /
• pp.152-177
• /
• 2021

Purpose - This study analyses the excepted requirement and burden of proof of the carrier due to unseaworthiness through comparison between the marine transport contract and marine insurance contract. Design/methodology - This study uses the legal analytical normative approach. The juridical approach involves reviewing and examining theories, concepts, legal doctrines and legislation that are related to the problems. In this study a literature analysis using academic literature and internet data is conducted. Findings - The burden of proof in case of seaworthiness should be based on presumed fault, not proved fault. The burden of proving unseaworthiness/seaworthiness should shift to the carrier, and should be exercised before seeking the protections of the law or carriage contract. In other words, the insurer cannot escape coverage for unfitness of a vessel which arises while the vessel is at sea, which the assured could not have prevented in the exercise of due diligence. The insurer bears the burden of proving unseaworthiness. The warranty of seaworthiness is implied in hull, but not protection and indemnity policies. The 2015 Act repeals ss. 33(3) and 34 of MIA 1906. Otherwise the provisions of the MIA 1906 remain in force, including the definition of a promissory warranty and the recognition of implied warranties. There is less clarity about the position when the source of the loss occurs before the breach of warranty but the actual loss is suffered after the breach. Nonetheless, by s.10(2) of the 2015 Act the insurer appears not to be liable for any loss occurring after the breach of warranty and before there has been a remedy. Originality/value - When unseaworthiness is identified after the sailing of the vessel, mere acceptance of the ship does not mean the party waives any claims for damages or the right to terminate the contract, provided that failure to comply with the contractual obligations is of critical importance. The burden of proof with regards to loss of damage to a cargo caused by unseaworthiness is regulated by the applicable law. For instance, under the common law, if the cargo claimant alleges that the loss or damage has been caused by unseaworthiness, then he has the burden of proof to establish the followings: (i) that the vessel was unseaworthy at the beginning of the voyage; and that, (ii) that the loss or damage has been caused by such unseaworthiness. In other words, if the warranty of seaworthiness at the inception of the voyage is breached, the breach voids the policy if the ship owner had prior knowledge of the unseaworthy condition. By contrast, knowingly permitting the vessel to break ground in an unseaworthy condition denies liability only for loss or damage proximately caused by the unseaworthiness. Such a breach does not, therefore, void the entire policy, but only serves to exonerate the insurer for loss or damage proximately caused by the unseaworthy condition.