• Proceedings of KOSOMES biannual meeting
• /
• 2007.05a
• /
• pp.109-113
• /
• 2007

Yacht have an high powered main engine relatively light hull, so the noise generated from the engine have a bad influence upon the crew and passenger. Recently, cruise yacht is made an attempt by domestic production skill, however the insulation skill of the noise made by the main engine is not satisfy the real purchasing power of the buyer. Like this, yacht cabin's noise level is becoming the barometer to decide the purchase. the method to insufficient. However, if we use the skill of the monitoring equipment and the genetic algorithm system, the circumference of the main engine can be enclosed by an high quality absorbtion wall and the noise levels of the cabins are improved. In this study, the sound absorbtion barrier is experimentally researched by change the volume and the length of the neck for the Helmholtz resonator as the resonator can absorb the noise effectively.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.577-582
• /
• 2015

This paper is the fundamental study for the application of cold storage system to the transportation equipment by sea and land. This numerical study presents the solid-liquid phase change phenomenon of calcium chloride solution of 30wt %. The governing equations are 1-dimensional unsteady state heat transfer equations of $1^{st}$ order partial differential equations. This type of latent heat storage material is often usable in fishery vessel for controlling the temperature of container with constant condition. The governing equation was discretized with finite difference method and the program was composed with Mathcad program. The main parameters of this solution were the initial temperature of heat storage material, ambient temperature of cold air and the velocity of cold air. The data of boundary layer thickness becomes thin with the increasing of cold air flowing velocity and also the heat storage completion time become shorten.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.129-130
• /
• 2017

This paper suggests study of basic structure design and structural analysis for the twin car-ferries. The rules and methodology for the analysis of strength of medium and small high speed vessels with a length of more than 50m and a width / ratio of more than 12, such as car-ferries, have not been clarified yet. Therefore, in this paper, the scantling of the members is based on the Korea Classification standards, and the car-ferries standards were additionally applied to verify the structural strength of the design. The results of this study are expected to be useful as basic data related to structural design and structural analysis of high speed twin car-ferries.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.4
• /
• pp.441-445
• /
• 2000

Considering international status of our country as world class ship builder and geographical characteristics encircled by sea in three facets, controlling of air pollutants emission from marine engines becomes more and more important issue in recent days. Implementation of immediate pollutants emission control regulation and standardization of test and certification procedure are required to reduce air pollution from marine engines. But cost increments due to additional equipment of emission control device and development and certification test expenses as well as depreciation of fuel economy should be considered. To satisfy those air pollution reduction and economic requirements, we should make our own interpretation of IMO standard and implementation schedule depending on our country's status. For this purpose we measured NOx emission from small and middle class marine engines to calculate emission factor and total pollutant emission in our country. With the comparison and analysis of other countries emission control regulation we proposed basic data of total emission from marine engine and future emission control standard in our country. According to our estimation, 62% of total NOx emission of marine engines comes from fishing boat and 38% from commercial vessels. The portion of NOx emission from marine engine is 18.6% of whole country NOx emission. Due to the voyage characteristics of middle and large vessel and necessity of international harmonization of marine engine pollutants emission control standard, it is inevitable to adopt IMO standard for middle and large marine engines. But considering technological and cost effect of fishing boat operating in near sea, it is resonable to set a standard within 80% of measured value at the moment and gradually implement the same IMO standard in near future.

• Corrosion Science and Technology
• /
• v.9 no.1
• /
• pp.48-55
• /
• 2010

The many vessels are built with FRP(Fiber-Reinforced Plastic) material for small boats and medium vessels. However, FRP is impossible to be used for recyclable material owing to environmental problems and causes large proportion of collision accidents because radar reflection wave is so weak that large vessels could not detect FRP ships during the sailing. Hence, Al alloy comes into the spotlight to solve these kinds of problems as a new-material for next generation instead of FRP. Al alloy ships are getting widely introduced for fish and leisure boats to save fuel consumption due to lightweight. In this study, it was selected 6061-T6 Al alloy which are mainly used for Al-ships and carried out various electrochemical experiment such as potential, anodic/cathodic polarization, Tafel analysis, potentiostatic experiment and surface morphologies observation after potentiostatic experiment for 1200 sec by using the SEM equipment to evaluate optimum corrosion protection potential in sea water. It is concluded that the optimum corrosion protection potential range is -1.4 V ~ -0.7 V(Ag/AgCl) for 6061-T6 Al alloy, in the case of application of ICCP(Impressed current cathodic protection), which was shown the lowest current density at the electrochemical experiment and good specimen surface morphologies after potentiostatic experiment for Al-Mg-Si(6061-T6) Al alloy in seawater environment.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.1
• /
• pp.95-102
• /
• 2018

This paper proposes a dual lifting and its cooperative control system with two different kinds of floating cranes. The Mega-erection and Giga-erection in the ship building are used to handle heavier and wider blocks and modules as ships and off-shore platforms are enlarged. However, there is no equipment to handle such Tera-blocks. In order to overcome the limit on performance of existing floating cranes, the dual lifting is proposed in this research. In the dual lifting, two floating cranes are well-coordinated to add up the lift capabilities of both cranes without any loss such that virtually a single crane is lifting, maneuvering and unloading. Two main constraints for the dual lifting are as follows: First, two barges of floating cranes should be constrained as a rigid body not to cause a relative motion between two barges and main hooks of the two cranes should be controlled as main hooks of a single crane. In order words, it is necessary to develop the cooperative control of two floating cranes in order to sustain a center of gravity of the module and minimize the tilting angle during the lifting and unloading by the two floating cranes. Two floating cranes are handled as a master-slave system. The master crane is able to gather information about all working conditions and make a decision to control the individual hook speed, which communicates the slave crane by TCP/IP. The developed control system has been embedded in the real floating crane systems and the dual lifting has been demonstrated five times at SHI shipyard in 2015. The moving angles of the lifting module are analyzed and verified to be suitable for hoisting control. It is verified that the dual lifting can be applied for many heavier and wider blocks and modules to shorten the construction time of ships and off-shore platforms.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.67-70
• /
• 2005

As the demand of sea leisure increases recently, interest is converged sea safety and offer of quick and systematic information according to weather environment that change rapidly. Use of Electronic Navigational Chart(ENC) in the sea in offer of geography information through Mobile terminal was gone to level that run in PDA environment in domestic by bulky good physician data information and complicated processing way of island in the sea expression in sea, and is loaded in obligatory sailing equipment of ship yet and is used. In this paper, we develop server system that take charge index for offer of quick information through Restrictive resource management and Caching Technique, image conversion and database construction and fast search to service various marine leisure informations of Weather Data and so on and image information of ENC in the sea to Mobile portable phone terminal efficiently.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.159-163
• /
• 2005

Marine accidents of 70.9% have been caused by small ships less than 100 tons in the past 5 years(1998${\sim}$2002). This is ascribable to the graying and lack in expertise on shipping of small ship operators, and merchant ships are hindered from coastal navigation due to the increase of coastal fishing boats and liners. Currently, ECDIS and GPS Plotters are widely used as navigation equipment providing route information to operators, but it can not give any function of automatic route creation and route explanation, so they are available only experienced operators. Especially, the present situation is that no study is made of the automatic route creation and route explanation using ENC for ECDIS, substitution system of paper chart. In this paper, Navigation Guiding System(NGS) is proposed to generate an optimal route where ENC and GPS data is fusioned including the wind speed and direction of anemometer. The proposed system was testified by a simulation, and its effectiveness was verified.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.325-330
• /
• 2006

The container terminal is the unified transportation system which connects between a land transportation and a sea transportation. This system has many subsystems such as ship operation, yard transfer operation, yard storage system, gate operation, and information manage system. This paper presents a method of modeling a simulator with which user can evaluate the efficiency of the equipment and allocation policies in the container terminal. The final purpose is to estimate the efficiency of each equipments and the distribution policies. In a design step in the simulator development. We suggest the Object Oriented method with which the developer can easily design, because the object oriented method has the advantages of reusability and modularity.

• Journal of Navigation and Port Research
• /
• v.32 no.6
• /
• pp.481-487
• /
• 2008

Ship's wireless LAN was in the limelight as equipment of ease, cost reduction, various func tion al i ty. In the paper, a dual-bandpass filter for wireless LAN has proposed, which was designed by using dual-mode square loop resonator with square patch in compliance with 2.4 GHz and 5 GHz band of wireless LAN. The dual-bandpass filter could be designed by adjusting sizes of one perturbation element and three of reference elements in compliance with the frequency bands of 2.4 GHz and 5.8 GHz, Furthermore, new dual-bandpass filter was also designed by adjusting stopband of using open stubs in compliance with the frequency bands of 2.4 GHz and 5.2 GHz. The measured results for the fabricated dual-bandpass filters agreed well with the simulated ones, and hence, it was confirmed that the proposed design method is valid.