• Steel and Composite Structures
• /
• 제2권3호
• /
• pp.223-236
• /
• 2002

An analytical procedure based on the transfer matrix method to estimate not only the natural frequencies but also vibration mode shapes of the thin-walled members composed of interconnected cylindrical shell panels is presented. The transfer matrix is derived from the differential equations for the cylindrical shell panels. The point matrix relating the state vectors between consecutive shell panels are used to allow the transfer procedures over the cross section of the members. As a result, the interactions between the shell panels of the cross sections of the members can be considered. Although the transfer matrix method is naturally a solution procedure for the one-dimensional problems, this method is well applied to thin-walled members by introducing the trigonometric series into the governing equations of the problem. The natural frequencies and vibration mode shapes of the thin-walled members composed of number of interconnected cylindrical shell panels are observed in this analysis. In addition, the effects of the number of shell panels on the natural frequencies and vibration mode shapes are also examined.

• 대한기계학회논문집A
• /
• 제20권9호
• /
• pp.2875-2886
• /
• 1996

This work present the experimental resutls for the free vibration of unstiffened, stiffened cylindrical shell filled with air, half water and full water. The natural frequencies and mode shapes of unstiffened, stiffened cylindrical shell are obtained experimentally also. The natural frequencies of stiffened cylindrical shell were generally highter than those of unstiffened cylindrical shell and natural requencies were decreased as cylindrical shell was filled with water. The effect of circumferential stiffener in the first mode was shown that natural frequency more increased 25% at air environment, 29% at half water environment and 37% at full water than those of unstiffened cylindrical shell, respectively. Also, the natural frequencies were decreased according to the added mass effect of fluid in the shell of unstiffened and stiffened cylindrical shell. The six mode shape results of all cases are simular and given. The natural frequencies are determined for a wide range of parameters : e.g. unstiffened shell, and filled with air, half and full water. The effects of varying the parameters on the free vibration frequencies and mode shapes are discussed.

• Structural Engineering and Mechanics
• /
• 제8권1호
• /
• pp.39-51
• /
• 1999

The dynamic response of buried pipelines has gained considerable importance because these pipelines perform vital role in conducting energy, water, communication and transportation. After realizing the magnitude of damage, and hence, the human uncomfort and the economical losses, researchers have paid sincere attention to this problem. A number of papers have appeared in the past which discuss the different aspects of the problem. This paper presents a theoretical analysis of non-axisymmetric dynamic response of buried orthotropic cylindrical shell subjected to a moving load along the axis of the shell. The orthotropic shell has been buried in a homogeneous, isotropic and elastic medium of infinite extent. A thick shell theory including the effects of rotary inertia and shear deformation has been used. A perfect bond between the shell and the surrounding medium has been assumed. Results have been obtained for very hard (rocky), medium hard and soft soil surrounding the shell. The effects of shell orthotropy have been brought out by varying the non-dimensional orthotropic parameters over a long range. Under these conditions the shell response is studied in axisymmetric mode as well as in the flexural mode. It is observed that the shell response is significantly affected by change in orthotropic parameters and also due to change of response mode. It is observed that axial deformation is large in axisymmetric mode as compared to that in flexural mode.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1285-1289
• /
• 2006

In a large diameter piping system, high frequency energy can produce excessive noise, high vibration, and failures of thermo-well, instrumentation, and attached small-bore piping. High frequency energy is generated by flow induced vibration like vortex shedding in orifices and valves. Once this energy is generated, amplification may occur from acoustical and/or structural resonances, resulting in high amplitude vibration and noise. At low frequencies, pipe vibration occurs laterally along the pipe's length, but at higher frequencies, the pipe shell wall vibrates radially across its cross-section. The simple beam analogy which is based on the beam mode vibration can not be applied to evaluate shell mode vibration. ASME OM3 recommends that the stress be measured directly by strain gauge and be evaluated according to the fatigue curves of the piping material. This Paper discusses the excitation and amplification mechanism relevant to high frequency energy generation in piping system, the monitoring method of the shell mode vibration in ASME OM3, the evaluation method generally used in the industry. Finally this paper presents the stress evaluation of the cavitating venturi down stream piping, where high frequency shell mode vibrations were observed during the operation.

• 소음진동
• /
• 제8권5호
• /
• pp.936-948
• /
• 1998

A theoretical formulation for the analysis of free vibration of a cylindrical shell with a circular plate attached at an arbitrary axial position of the shell under various kinds of boundary conditions was derived and programed to get the numerical results for natural frequencies and mode shapes of the combined system. The boundary conditions of the shell to be considered here are clamped-free, clamped-simply supported, both ends clamped and both ends simply supported. The frequencies and mode shapes from theoretical calculation were compared with those of commercial finite element code, ANSYS. The results showed good agreement with those of ANSYS in frequencies and mode shapes. The program will contribute to the design optimization of a shell/plate combined system through the analysis of natural frequencies and mode shapes for the system.

• Advances in concrete construction
• /
• 제14권5호
• /
• pp.309-315
• /
• 2022

This paper depicts the diagram of cylindrical shells as an essential idea. It centers around an outline of exploration and use of cylindrical shell in expansive current circumstance. In view of investigation of the current and prospect of model as a piece of present exploration work, a straightforward contextual analysis is examined with Love's shell theory based on Galerkin's method. The cylindrical shells are attached from one end of the cylindrical shells. The frequencies of ring support shells are investigated against the half axial wave mode. The frequencies increase on increasing the half axial wave mode. Also, the frequencies are downsized with ring supports. The software MATLAB is preferred to others because in this software computing coding is very easy to do. Just single command 'eig' furnishes shell frequencies and mode shapes by calculating eigenvalues and eigenvectors respectively. The shell vibration frequencies for cylindrical shells are compared with those results found in the open literature.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.314-319
• /
• 1995

The effect of liquid level on the natural frequencies and mode shapes of a partially liquid-filled circular cylindrical shell with various boundary conditions is investigated by means of a theoretical analysis based upon Fourier series expansion method and a finite element analysis using ANSYS computer program. Two dimensional mode shapes of the liquid-coupled shell structure are obtained by the ANSYS finite element analysis and show that the liquid level affect the nodal point movement. It is found that the variation of normalized naturalfrequencies (natural frequencies of liquid-filled shell/antural frequencies ofempty shell) to the liquid level is depend on the axial mode numbers and circumferential wave numbers. Additionally, it is found that the number of variational steps of normalized natural frequencies is identicial to that of axial nodal points of the mode shape.

• 한국해안해양공학회지
• /
• 제3권3호
• /
• pp.117-125
• /
• 1991

유체 중에서 진동하고 있는 얇은 원통형 탄성쉘의 고유진동수를 계산할 수 있는 두 가지 방법을 제시하였다. 두 방법 모두 고유진동수를 해석적인 형태로 나타내었다. 하나는 간단한 형태로서 쉘의 고차변형모드에 적합하고 다른 하나는 정확하며 유체중에 부분 잠수된 쉘의 경우에 사용된다. 쉘이 유체중에 완전 잠수된 경우로서, 저차변형모드에 대해서는 주위유체가 고유진동수에 상당한 영향을 미침을, 그리고 고차변형모드에 대해서는 그 영향이 작음을 알 수 있었다. 그러나 쉘이 유체중에 부분잠수된 경우에는 최저변형모드에서 항상 위 영향이 최대가 되는 것은 아니었다.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.383-391
• /
• 1986

본 논문에서는 이들 기본모우드형태가 검토되었고 또한 두께효과와 비대칭성 효과에 따른 고유진동주파수, 모우드형태, 울림주파수의 변화를 수치적 해석과 실험 적 해석방법에 의해 비교검토되었다. 수치해석방법은 유한요소법으로 이용된 프로그 램은 NASTRAN 프로그램이고 모우드의 형태는 Tectronics컴퓨터그래픽을 이용하여 나타 내었다. 실험적방법은 충격햄머법과 F.F.T. 분석장치(Fast Fourier Transformation Analyzer)를 이용하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.353.1-353
• /
• 2002

Impulse response of a slightly asymmetric cylindrical shell is derived. Receptance method is applied to obtain the vibration mode and natural frequency of the slightly asymmetric cylindrical shell. Impulse response model is used to identify the vibration beat characteristics of King Song-Dok Bell. The theretical mode is compared and verified by the measured mode of King Song-Dok Bell. (omitted)