• Journal of Korean Society on Water Environment
• /
• v.21 no.1
• /
• pp.29-33
• /
• 2005

In order to recycle the waste material and to develop the thickening unit of waste activated sludge from wastewater treatment facilities, the filtration bio-reactor equipped with a shadow mask filter module was employed for this work from which the operating properties and parameters were drawn. The sludge thickening and filtration unit is made of cylindrical acryl tank(12cm i.d. ${\times}$ 58cm height: working volume of 6L), where the flat-sheet type of shadow mask filter module(pore size: 220~250um, opening area: 34.8~39.6%) was installed and the effluent was withdrawn from the effluent port at the lowest point of the reactor, and the filtration was performed only by the hydraulic pressure. For evaluating the operating performance of this reactor, some parameters such as the solid-liquid separation of different biomass concentrations, the water quality of filtrate, the aeration cleaning time and the cleaning effect were investigated. Depending on the MLSS concentrations, the different time to withdraw 3L of filtrate was required in which the longer filtration time was necessary for the higher MLSS concentrations caused by the thicker formation of cake layer: 40 minutes for 5,000 mg/L, 70 minutes for 10,000 mg/L and 100 minutes for 15,000 mg/L, where the concentrations of SS were 8.9, 6.7 and 6.5 mg/L, respectively. Under the same operating conditions (the intensity of aeration cleaning: 80 L/min, MLSS: 10,000 mg/L), the proper aeration cleaning time was revealed 30 seconds, and the stable formation of cake layer was in the range of 10 to 15 minutes. Therefore, the shadow mask considered as a waste material can be of use as a filter material for the sludge thickening system.

• Corrosion Science and Technology
• /
• v.23 no.3
• /
• pp.215-220
• /
• 2024

Recently, the demand for Zn-Ni electrogalvanized steel sheets for home appliances and automobiles is increasing. Products should have a thick plating (30 to 40 g/m²) on both side with a thin thickness (≤ 0.8 mm) and the highest surface quality. By a high current density operation, current is concentrated in the edge part of the steel sheet, resulting in large surface dent defects due to dendritic plating. This can lead to a low productivity due to low line speed operation. To solve this problem, this study aimed to identify factors influencing dendritic plating. A cylindrical electroplating device was manufactured. Effects of cut edge shape and thickness of steel plate, current density, temperature, flow rate, electrolyte concentration, and pH on dendrite generation of Zn-Ni electroplating were examined. To investigate effect of edge shape of the steel sheet, the steel sheet was manufactured using three processing methods: shearing, polishing after shearing, and laser. Relative effects thickness and cut edge processing methods of the steel plate, current density, temperature, flow rate, electrolyte concentration, and pH of plating solution on dendrite plating were investigated. To prevent dendrite plating, an edge mask was manufactured and its application effect was investigated.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.290-295
• /
• 2004

Mircolens and microlens V-groove are realized using a novel fabrication technology based on the exposure of a resist, usually PMMA, to deep X-rays and subsequent thermal treatment and inclined deep X-ray lithography, respectively. The fabrication technology is very simple and produces microlenses and microlens V-groove with good surface roughness of several nm. The molecular weight and glass transition temperature of PMMA is reduced when it is irradiated with deep X-rays. The microlenses were produced through the effects of volume change, surface tension, and reflow during thermal treatment of irradiated PMMA. Microlenses were produced with diameters ranging from 30 to $1500\mu\textrm{m}$. The surface X-ray mask is also fabricated to realize microlens arrays on PMMA sheet with a large area. The size of the micro V-groove is fabricated in the range of 12~$60\mu\textrm{m}$.

• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.159-165
• /
• 2017

We were investigated the content of 7 preservatives for sheet mask samples(n=42) sold in markets of Daejeon metropolitan city in 2016. &3.3%(n=35) of all samples contained at least one of preservatives. In samples of 30.95(n=14) and 2.39%(n=1) was detected with 2 and 3 preservatives. Phenoxyethaol(PE), methylparaben(MP), chlorphenesin(CP) and benzyl alcohol(BA) showed detection rate of 76.19(n=32), 16.67(n=9), 21.43(n=7) and 2.38%(n=1), respectively. Also The content of detected preservative showed range of 0.06~0.71, 0.18~0.35, 0.06~0.71 and 0.32% and was within the maximum allowed amount established by Korean FDA. However ethylparaben(EP), propylparaben(PP) and benzylparaben(BP) in all samples was not detected. These results can be useful for sharing in emotion-fusioned information and supplying right to know of user.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.9
• /
• pp.22-29
• /
• 1997

This paper describes a three dimensional profile measurement method for sheet metal products which have flexible and porous sculptured surfaces. Shadow masks are used as measuring objects for practical implementation or this study. The shadow masks are located inside the fluorescent glasses of monitors for televisions or computers and used to prevent electron guns from interfering between pixels. Three dimen- sional surface profiles are measured by adopting a software autofocusing technique to capture focused images. The experimental results show that the method is very effecive and suitable for sheet meal prod- ucts with flexible and porous surfaces.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.261-266
• /
• 1993

This paper describes a 3-dimensional profile measurement method which was intended especially for sheet metal products such as shadow masks. The method is based upon machine vision in which the height variation of the surface is measured by software auto-forus image processing techniques. The method is found suitable for flexible surfaces with interrupt.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.3
• /
• pp.314-319
• /
• 2015

Invar is a compound metal of Fe-Ni system contained 36.5% Ni. The characteristic of invar is that the coefficient of thermal expansion is $1.0{\times}10^{-6}cm/^{\circ}C$. It is approximately 10 times smaller than series of steel. Because of this low thermal expansion characteristic of Invar, it is used to shadow mask of display device such as UHDTV or OLED TV. In this study, pulse current from pulse generator instead of DC current is used to overcome the disadvantages of the conventional electrochemical machining. Pulsed current with different duty factor in PECM affect the precise geometry. Pulse electrochemical machining is conducted to machine the micro hole to the invar sheet with different duty factor. The machined shape and overcut of invar sheet with different duty factor is observed by optical microscope and scanning electron microscope (SEM).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.36-43
• /
• 2020

The extracts of antioxidants, torreya nucifera and alphinia henryi, were tested for properties as a fragrance material and applied to a mask pack formulation to study the fragrance properties. The DPPH antioxidant test of hot water and ethanol extract confirmed that the ethanol extract had superior antioxidant efficacy compared to the hot water extract. It was confirmed that the optimal mixing ratio as a raw material for the mask pack of torreya nucifera and alphinia henryi was 3:7 as a result of the DPPH antioxidant test. As a result of the cytotoxicity test, the cell viability was good as it showed 103.30% at 0.5 ug/mL, 104.25% at 1 ug/mL, 102.56% at 5 ug/mL, and 99.17% at 10 ug/mL compared to the untreated group. As a result of the patch test on the mask pack formulation, the skin irritation index of 0.02 was judged as a non-irritation product in the skin irritation primary stimulation human application test. In the evaluation of skin moisturizing, it showed a significant increase rate of 19.178% compared to before the sample adaptation. Evaluation of the change over time in the sheet mask pack formulation confirmed the formulation stability without viscosity and pH change for 12 weeks at low temperature(4℃), room temperature(25℃), and high temperature(45℃).

• Journal of the Korean Solar Energy Society
• /
• v.32 no.5
• /
• pp.102-107
• /
• 2012

Halogen lamp was applied to fabricate the selective emitter crystalline silicon solar cell. In selective emitter structure, the recombination of minority carriers is reduced with heavily doped emitter under metal grid, consequently improving the conversion efficiency. Laser selective emitter process which is recently used the most generally induces the damage on the silicon surface. However the lamp has enough heat to form heavily doped emitter layer by diffusing phosphorus from PSG without surface damage. In this work, we have studied to find the design and the suitable condition for halogen lamp such as power, time, temperature and figured out the possibility to fabricate the selective emitter silicon solar cell by lamp heating. The sheet resistance with $100{\Omega}/{\Box}$ was lower to $50{\Omega}/{\Box}$ after halogen lamp treatment. Heat transfer to lightly doped emitter region was blocked by using the shadow mask.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.228-232
• /
• 2003

Mircolens and microlens arrays are realized using a novel fabrication technology based on the exposure of a resist, usually PMMA, to deep X-rays and subsequent thermal treatment. Hot embossing process is also studied for mass production. The fabrication technology is very simple and produces microlenses and microlens arrays with good surface roughness of several nm. The molecular weight and glass transition temperature of PMMA is reduced when it is irradiated with deep X-rays. The microlenses were produced through the effects of volume change, surface tension. and reflow during thermal treatment of irradiated PMMA. A hot embossing machine is designed and manufactured with a servo motor transfer system. The hot embossing process follows the steps of heating mold to the desired temperature, embossing a mold insert on substrate. cooling mold to the de-embossing temperature. and de-embossing. Microlenses were produced with diameters ranging from 30 to 1500 ${\mu}{\textrm}{m}$. The surface X-ray mask is also fabricated to realize microlens arrays on PMMA sheet with a large area.