• 전기학회논문지
• /
• 제65권12호
• /
• pp.2014-2018
• /
• 2016

Transparent, conductive electrode films, showing the particular characteristics of good conductivity and high transparency, are of considerable research interest because of their potential for use in opto-electronic applications, such as smart window, photovoltaic cells and flat panel displays. Multilayer transparent electrodes, having a much lower electrical resistance than widely-used transparent conducting oxide electrodes, were prepared by using RF/DC magnetron sputtering system. The multilayer structure consisted of three layers, [NiInZnO(NIZO)/Ag/NIZO]. The optical and electrical properties of the multilayered NIZO/Ag/NIZO structure were investigated in relation to the thickness of each layer. The optical and electrical characteristics of multilayer structures have been investigated as a function of the Ag and NIZO film thickness. High-quality transparent conductive films have been obtained, with sheet resistance of $9.8{\Omega}/sq$ for Ag film thickness of 8 nm. Also the multilayer films of inserted Ag 8 nm thickness showed a high optical transmittance above 93% in the visible range. The electrical and optical properties of the new multilayer films were mainly dependent on the thickness of Ag insertion layer.

• 설비공학논문집
• /
• 제14권1호
• /
• pp.63-72
• /
• 2002

The main objective of this study is to propose a practical two-microphone impedance tube method to measure the sound transmission loss for flexible sound isolation sheets without the use of the time-consuming and expensive reverberation room. This method was based on the sound decomposition theory developed by Seybert using the spectral density functions of the incident and reflected sound waves. In order to verify the validity of the experimental results, the measured sound transmission losses from the proposed method were compared with the measured data from the reverberation room method and the calculated data from the theory satisfying the mass law of sound isolation material. The resulted trends of the sound transmission losses versus frequencies for several different sound isolation sheets were almost same for each other and agreed quite well in both methods except at some low frequency region. From the experimental results, it was found that the accuracy of sound isolation capability obtained by two-microphone impedance tube method depends upon the microphone spacing, the distance from the first microphone to the test sample surface and the test sample location.

• 한국정보통신학회논문지
• /
• 제8권3호
• /
• pp.614-621
• /
• 2004

현재의 전자문서처리 환경은 WYSIWYG 방식이다. 이를 위해 문서를 논리적인 구조와 물리적인 구조로 구조화하였고 이러한 구조를 마크업언어로 표현하고 있다. 특히 인터넷상의 전자문서 작성 및 교환을 위한 마크업언어로 XML이 발표되어 전자문서의 표현과 같은 전통적인 사용에서부터 검색을 위한 데이터베이스화에 이르기까지 전자문서의 활용 영역이 다양해지고 있다. 그러나 출력 품질면에서 워드프로세서나 전자출판에 의한 전자문서와 XML 문서의 출력 품질은 매우 큰 차이가 있다. 이는 비록 XML 문서가 스타일 정보를 포함하고 있긴 하지만 화면 출력과 인쇄 매체로의 출력 모두 고품질의 출력을 위한 적용이 부족했기 때문이다. 이러한 문제 해결을 위해 W3C에서는 고품질의 XML 출력 문서를 얻을 수 있도록 XSL-FO(XSL-Formatting Object)를 개발하였다. 한편 고품질의 전자출판물을 얻기 위해 폐이지 기술 언어(PDL)가 필요하고, 이의 업계표준인 Postscript가 이미 널리 사용되고 있다. 따라서 본 논문에서는 XML-FO를 PostScript에 적용함으로써 고품질의 XML 출력문서를 얻기 위한 변환기를 설계하였다.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제29권1_2호
• /
• pp.20-29
• /
• 2002

복합 재료로 구성된 원판으로부터 여러 가지 패턴을 버려지는 부분이 최소화되게 배치시킨 후 절단하는 문제를 복합 재료 재단 문제라 부른다. 본 논문은 목적 함수의 비용 오류를 감내하는 영역 분할 분산 시뮬레이티드 어닐링 알고리즘을 MPI 환경하에서 복합 재료 재단 문제에 적용한다. 비용 오류 감내기법은 최적해 접근 특성을 유지하기 위하여 스트림 길이를 동적으로 변화하며 상태변환을 비동기적으로 수행한다. 또한 복합 재료 재단 도구 개발을 위한 여러 가지 모양을 가진 패턴의 정보 및 친화도 생성, 목적함수, 상태변환 방법, 어닐링 스케줄 및 이를 위한 효율적인 자료 구조에 대하여 정의한다. 배치될 패턴은 정형이나 convex 다각형으로 제한되어 있지 않고 어떠한 모양도 가능하며 원판은 복합 재료의 성격상 2 또는 4 방향으로 고정되어 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.467-468
• /
• 2006

We report on the fabrication of P3HT-based thin-film transistors (TFT) that consist of indium-zinc-oxide (IZO), PVP (poly-vinyl phenol), and Ni for the source-drain (S/D) electrode, gate dielectric, and gate electrode, respectively. The IZO S/D electrodes of which the work function is well matched to that of P3HT were deposited on a P3HT channel by thermal evaporation of IZO and showed a moderately low but still effective transmittance of ~25% in the visible range along with a good sheet resistance of ${\sim}60{\Omega}/{\square}$. The maximum saturation current of our P3HT-based TFT was about $15{\mu}A$ at a gate bias of -40V showing a high field effect mobility of $0.05cm^2/Vs$ in the dark, and the on/off current ratio of our TFT was about $5{\times}10^5$. It is concluded that jointly adopting IZO for the S/D electrode and PVP for gate dielectric realizes a high-quality P3HT-based TFT.

• 대한기계학회논문집A
• /
• 제36권9호
• /
• pp.997-1002
• /
• 2012

수송기기의 연비향상과 에너지 절감을 위하여 자동차 업계를 비롯한 각종 산업 전반에 마그네슘 합금의 적용이 확대되고 있는 추세이다. 조밀육방 격자 구조(HCP)를 갖는 마그네슘 합금의 경우, 낮은 성형성과 강한 소성 비대칭성 및 소성 이방성으로 인하여 실제 부품의 적용에 많은 제약조건이 수반되고 있다. 본 논문에서는 CPB06 항복함수를 이용하여 AZ31의 인장-압축 비대칭성을 모델링하고 이를 이용하여 AZ31 튜브의 압괴해석을 수행하고자 하였다.

• 해양환경안전학회지
• /
• 제20권6호
• /
• pp.746-751
• /
• 2014

본 논문에서는 소스 코드가 공개된 라이브러리를 이용하여 선박의 성능을 예측할 수 있는 해석 코드를 개발하였다. 질량보존 방정식, 모멘튼 보존방정식, 난류를 고려하기 위해 난류모델과 벽함수를 고려하였다. 자유수면 계산을 위해 볼륨비 수송방정식을 고려하였고, 자유수면의 정확도 높은 계산을 위해 고차 도식을 포함하는 라이브러리를 개발하였다. 개발한 프로그램을 컨테이너선인 KCS에 적용한 결과 실험에서 포착된 자유수면 분포를 잘 예측하였다. 자항성능 평가 시 추진기 회전을 위해 GGI 라이브러리를 사용하였다. 계산결과 실험과 비교해 약 7 % 정도의 정확도로 자항성능을 예측하였다. 캐비테이션 예측을 위해 이상 균질 모델을 포함하는 새로운 라이브러리를 개발하였다. 이상 균질 모델을 추진기에 적용한 결과 일반적으로 발생하는 얇은 층 캐비테이션을 잘 예측하는 것을 확인하였다. 오픈 소스 라이브러리를 이용하여 개발한 수치수조를 KCS에 적용한 결과 오픈 소스 라이브러리에 대한 가능성을 확인하였다.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1241-1248
• /
• 2018

The reactive wetting behaviors of molten Zn-Al-Mg alloys on MnO- and amorphous (a-) $SiO_2$-covered steel sheets were investigated by the sessile drop method, as a function of the Al and Mg contents in the alloys. The sessile drop tests were carried out at $460^{\circ}C$ and the variation in the contact angles (${\theta}_c$) of alloys containing 0.2-2.5 wt% Al and 0-3.0 wt% Mg was monitored for 20 s. For all the alloys, the MnO-covered steel substrate exhibited reactive wetting whereas the $a-SiO_2$-covered steel exhibited nonreactive, nonwetting (${\theta}_c>90^{\circ}$) behavior. The MnO layer was rapidly removed by Al and Mg contained in the alloys. The wetting of the MnO-covered steel sheet significantly improved upon increasing the Mg content but decreased upon increasing the Al content, indicating that the surface tension of the alloy droplet is the main factor controlling its wettability. Although the reactions of Al and Mg in molten alloys with the $a-SiO_2$ layer were found to be sluggish, the wettability of Zn-Al-Mg alloys on the $a-SiO_2$ layer improved upon increasing the Al and Mg contents. These results suggest that the wetting of advanced high-strength steel sheets, the surface oxide layer of which consists of a mixture of MnO and $SiO_2$, with Zn-Al-Mg alloys could be most effectively improved by increasing the Mg content of the alloys.

• Current Optics and Photonics
• /
• 제6권6호
• /
• pp.550-564
• /
• 2022

Optical microscopy is a useful tool for study in the biological sciences. With an optical microscope, we can observe the micro world of life such as tissues, cells, and proteins. A fluorescent dye or a fluorescent protein provides an opportunity to mark a specific target in the crowd of biological samples, so that an image of a specific target can be observed by an optical microscope. The optical microscope, however, is constrained in resolution due to diffraction limit. Super-resolution microscopy made a breakthrough with this diffraction limit. Using a super-resolution microscope, many biomolecules are observed beyond the diffraction limit in cells. In the case of volumetric imaging, the super-resolution techniques are only applied to a limited area due to long imaging time, multiple scattering of photons, and sample-induced aberration in deep tissue. In this article, we review recent advances in super-resolution microscopy for volumetric imaging. The super-resolution techniques have been integrated with various modalities, such as a line-scan confocal microscope, a spinning disk confocal microscope, a light sheet microscope, and point spread function engineering. Super-resolution microscopy combined with adaptive optics by compensating for wave distortions is a promising method for deep tissue imaging and biomedical applications.

• The Journal of Korean Physical Therapy
• /
• 제33권1호
• /
• pp.7-15
• /
• 2021

Purpose: This study was examined to improve the standing posture of a scoliosis client using the ICF Tool. Methods: For examination, the study subject was a 16-year-old female student diagnosed with 3curve-pelvic (3CP) type scoliosis. Information about her were collected through a client interview and based on international Classification of Functioning, Disability and Health (ICF). The ICF core set was for post-acute musculoskeletal conditions, and the ICF level 2 items suggested by National Rehabilitation Information Center (NARIC) were added to the recommendations for scoliosis. For evaluation, the ICF assessment sheet was used to identify the interaction among the problems. For the diagnosis, the client's functional problems were described in ICF terms. For the prognosis, the global goals for reaching the client's functional activity and participation level were presented as the long-and short-term goals. For the intervention, a coordinative locomotor training program composed of warm-up, main exercise, and cool-down was applied 3 times a week, 50 minutes a day, for 5 weeks. For the outcome, the differences between before and after the intervention were compared with the ICF qualifier and are shown with the ICF evaluation display. Results: Clinical advantages were observed in body function and structure (7° decrease of thoracic angle, 7 score increase of trunk muscle power, 6.47s improve of one leg standing, 4 score decrease of neck pain). The activity for maintaining the standing posture, in which the client had a primary limitation, was improved. Conclusion: Applying the coordinative locomotor training program is expected to improve scoliosis client's standing posture.