• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.4
• /
• pp.135-139
• /
• 2014

The hydride vapor phase epitaxy (HVPE) grown GaN samples to precisely measure the surface characteristics was applied to a molten KOH/NaOH wet chemical etching. The etching rate by molten KOH/NaOH wet chemical etching method was slower than that by conventional etching methods, such as phosphoric and sulfuric acid etching, which may be due to the formation of insoluble coating layer. Therefore, the molten KOH/NaOH wet chemical etching is a better efficient method for the evaluation of etch pits density. The grown GaN single crystals were characterized by using X-ray diffraction (XRD) and X-ray rocking curve (XRC). The etching characteristics and surface morphologies were studied by scanning electron microscopy (SEM). From etching results, the optimum etching condition that the etch pits were well independently separated in space and clearly showed their shape, was $410^{\circ}C$ and 25 min. The etch pits density obtained by molten KOH/NaOH wet chemical etching under optimum etching condition was around $2.45{\times}10^6cm^{-2}$, which is commercially an available materials.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.4
• /
• pp.308-313
• /
• 2014

Recently, for longevity of resident building, the main trend is that the change of the inside space organization of resident building from wall construction to rhamen construction, which resulted in increase in use of lightweight composite panel. Thus, in this study, authors analyzed the engineering property of oxide of magnesium depending on the magnesium chloride addition ratio. The results of this research is expected to contribute on providing a fundamental material for the surface materials of lightweight composite panel. As the result of the experiment, as fluidity increased, air content decreased and initial set and final set as the magnesium chloride addition ratio increase. In the aspect of flexural strength and compressive strength, the test specimen showed the highest strength at 40% of the magnesium chloride addition ratio. At 20% of the magnesium chloride addition ratio, the test specimen showed the lowest water absorption rate. As the magnesium chloride addition ratio increases, the expansibility tends to increase as well in the aspect of shrinkage strain. After observing microstructure, we can see hydration products in the form of needle. It appeared high flexural strength because the hydration products have mineral fibrous tissue shape, which also contribute to the cause of the expansibility.

• The Journal of Dong Guk Oriental Medicine
• /
• v.6 no.1
• /
• pp.117-128
• /
• 1997

Abdominal skin tissues of ICR mouse painted with Dinitrochlorobenzene (DNCB) were observed to investigate the delayed type hypersensitivity of skin by chemical allergen as hapten. The abdominal skin tissues were obtained at hour 48 after secondary DNCB sensitization that were stained by Luna's method for mast cell, and immunohistochemical stain method for IL-2 receptor. The superficial perivascular lymphocytic aggregation were shown in basement membrane after DNCB secondary painting and the large size capillaries in dermis were appeared. The infiltration of lymphocyte to epithelium, the vacuolation of epithelial cell and intercellular space were increased. The number of mast cell in dermis was increased and these shape is degranulation type. The number of IL-2 receptor positive cell was increased in dermis. As results indicated that the hypersensitivy of immune system were induced by DNCB, subsequently to damage evoke inflammation in skin.

• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.147-156
• /
• 2011

Since the urbanization process has been taking place, negative outcomes such as environmental pollution and traffic congestion have produced as well. Reflecting the phenomenon, our study assumed that physical structure of urban form were implicit in relation to both economic performance and cost. It can be interpreted that as the urban space has been growing bigger, economic performances such as regional product output, economy of scale and the effect of agglomeration economies are increased. On the contrary, the negative effects such as environmental pollution and traffic congestion were incurred as economic loss and expenses. It means that even though economic performance can help increase regional product output, we should consider the loss on economic expenses which are paid for social problems such as environmental pollution and traffic congestion, which are caused by urbanization. Therefore, this study aims to statistically validate the relationship between traffic congestion as the most representative economy costs and physical characteristics of urban in a large city such as Seoul and to suggest its implications. As a result of model development for empirical analysis, GRDP(0.604), the population(0.582), employment GINI coefficients(0.296), population GINI coefficients(0.254) in order led to congestion cost. We can come to the conclusion that in case of scale factor such as the population, if the population tends to concentrate, urban becomes more crowded and that if GINI coefficients (the population, employment) which are variable on inequality according to region have the disparity with surrounding areas, congestion cost is caused a lot on account of movement related with employment. In addition, this phenomenon was caused if both the population and employment were geographically biased on one side.

• Journal of Korea Water Resources Association
• /
• v.45 no.3
• /
• pp.275-290
• /
• 2012

In this study, we have developed an optimal time distribution model through extraction of peaks over threshold (POT) series. The median values for annual maximum rainfall dataset, which are obtained from the magnetic recording (MMR) and the automatic weather system(AWS) data at Seoul meteorological observatory, were used as the POT criteria. We also suggested the improved methodology for the time distribution of extreme rainfall compared to Huff method, which is widely used for time distributions of design rainfall. The Huff method did not consider changing in the shape of time distribution for each rainfall durations and rainfall criteria as total amount of rainfall for each rainfall events. This study have suggested an extracting methodology for rainfall events in each quartile based on interquartile range (IQR) matrix and selection for the mode quartile storm to determine the ranking cosidering weighting factors on minutely observation data. Finally, the optimal time distribution model in each rainfall duration was derived considering both data size and characteristics of distribution using kernel density function in extracted dimensionless unit rainfall hyetograph.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.4
• /
• pp.77-86
• /
• 2013

Laboratory pullout tests were conducted to evaluate pullout performance of steel strip reinforcements with deformed steel bars as transverse members. The steel strip reinforcement has an installation hole to assemble a deformed steel bar. Jumunjin standard sand is used to form a relative density of ground model to 80%. Frictional resistance of steel strip reinforcement without transverse member increases sharply at the initial displacement and quickly decreases with displacement. Maximum frictional resistance increases linearly as normal pressure increasing, and soil-reinforcement interaction friction angle(${\rho}_{peak}$) of a steel strip reinforcement is estimated to $14.64^{\circ}$. Passive resistance increases with displacement and converge into maximum passive resistance in most cases. Maximum passive resistance increases linearly as normal pressure increasing irrespective of shape of the steel reinforcement. Pullout force of steel strip reinforcements with installation holes or transverse members largely increases about 4 to 7 times compared to frictional resistance force of steel strip reinforcements when embedment length($L_e$) of steel strip reinforcements is 500 mm. In the case of using 2 transverse members, interference effect is observed due to the spacing of 2 transverse members and location of assembly holes and transverse members.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.116-124
• /
• 2009

Recently the CPU performance of modem chipsets or multimedia processors of mobile phone is as high as notebook PC. That is why mobile phone has been emerged as a leading ICON on the convergence of consumer electronics. The various applications of mobile phone such as DMB, digital camera, video telephony and internet full browsing are servicing to consumers. To meet all the demands the image quality has been increasingly important. Mobile phone is a portable device which is widely using in both the indoor and outside environments, so it is needed to be overcome to deteriorate image quality depending on environmental light source. Furthermore touch window is popular on the mobile display panel and it makes contrast loss because of low transmittance of ITO film. This paper presents the image enhancement algorithm to be embedded on image enhancement SoC. In contrast enhancement, we propose Clipped histogram stretching method to make it adaptive with the input images, while S-shape curve and gain/offset method for the static application And CIELCh color space is used to sunlight readability enhancement by controlling the lightness and chroma components which is depended on the sensing value of light sensor. Finally the performance of proposed algorithm is evaluated by using histogram, RGB pixel distribution, entropy and dynamic range of resultant images. We expect that the proposed algorithm is suitable for image enhancement of embedded SoC system which is applicable for the small-sized mobile display.

• Korean Journal of Ichthyology
• /
• v.11 no.1
• /
• pp.86-93
• /
• 1999

Artificial fertilization of flounder, Limanda herzensteini caught at Pohang brook was performed in April 13, 1995 and hatched larvae were reared for 25 days to describe the development of eggs and the morphogenesis of larvae. The fertilized egg was buoyant, colorless and spherical in shape, measuring 0.86~0.96 mm in diameter (mean: 0.90 mm), The egg has no oil globule, and its perivitelline space was narrow. Hatching in the indoor tank with $16.0^{\circ}C$ in mean water temperature started from the 64 hours after fertilization. The newly hatched larva, measuring about 2.80 mm in total length, had 10~11+25~27=35~38 myomeres. The anus is open at about the anterior point of the body. The 3 to 4 days old larva was 3.90 mm in total length. In this larva the eyes were black and the mouth was open. The yolk was consumed in 8 to 9 days. In 20 to 22 days after hatching, the larvae grew 6.1 mm in total length. The eyes were located symmetry on both sides of head.

• Journal of architectural history
• /
• v.15 no.1 s.45
• /
• pp.7-27
• /
• 2006

This study aims to identify and analyze the factors that influenced the construction of London Eye which was led by private groups, including characteristics in progress, differentiated value in design, the combination of technology and design, and construction costs. The results of this study were the followings. 1) London Eye provides a new construction method for a landmark in the downtown in that the architects became the clients of the project which might have been hoarded, procuring the construction costs and completing it by themselves. 2) London Eye presents a space utilization method where undeveloped spaces in the downtown are used in three-dimensions by erecting a structure on the river with a minimum land. 3) The process of design, production and erection is propelled the realization of technical intention design with one system and from at the initial stage, the participation of the engineer where the designer is equal with you must accompany. 4) London Eye is endowed with strong shape by a circle in design concept, which is the simplest geometrical figure, and it provides organic relationship between the past and the present by utilizing historical elements in various ways. 5) The construction was completed through four phases including idea phase, promotion phase, turn-key contract phase, and design-build phase. The most critical factor to the success is derived from the direct contact with Involved companies from the production phase. 6) In a project facing many challenges in terms of technology, the design-build method proves to be a more effective method than turn-key contract in that it may more allocate risks and enable coherent implementation of the core concept in design. The organization for the design-build method was composed of three phases including general affairs, responsible contracting by sector, and cooperative system by sector. Since that was a new concept structure, high-level contractors who hadn't had existing cooperative relationships with one another formed new cooperative relationship, while collaborating companies who had long cooperated led the responsible contracting and sub-cooperative system, which resulted in reduction of risks and time. 7) The major factors to change design were the design characteristics, derived from a technically great combination, and the opening time. 8) A new erection method was applied to London Eye, a structure that overcame the limitation in land and period, and the process of installation demonstrated that it is an important value for the construction of a landmark in the city. 9) In spite of many visitors and tremendous operational income, the factors that London Eye fails to free itself from debts include the construction costs expended double than expected, and interest burden to the investments, which occurred in the course of procuring the costs. Absolute limit in time increased the construction costs, resulting in being a great obstacle in the course of operation.

• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.228-236
• /
• 1996

An electrolysis system with a vertically circulating mercury capillary bundle electrode was developed with a very large electrode area in a minimum space. This system was operated by forcedly feeding mercury and aqueous solution containing metal ion into a fiber bundle packed densely within a small porous glass tube. In order to test the characteristics and stability of the electrolysis system, the reduction voltammograms of uranyl and ferric ions were measured with changes of the mercury flow rate and the aqueous flow rate. The aqueous flow rate had a large effect on the electrochemical reaction of metal ion occurring at the interface between the mercury and the aqueous solution and had to be regulated as an appropriate value to have a good limiting current shape. The limiting current was linearly proportional to the aqueous flow rate, and complete reductions of uranyl and ferric ions were rapidly and continuously accomplished at the potential showing limiting current. With a mercury flow rate high enough to keep a capillary continuum of mercury in the fiber bundle, the mercury flow rate had almost no effect on the electrochemical reaction. This system was confirmed to be effective and stable enough to control rapidly and continuously the oxidation state of metal ions fed into the system under an appropriate aqueous flow rate.