• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.67-75
• /
• 2019

The diaphragm used for CFT columns has a small amount of steel to be used, but has a disadvantage that welding is difficult and openings are required because the steel tube and four sides must be welded. The improved diaphragm to be examined in this study was cut into four corners by cutting the center hole for concrete filling. In the improved diaphragm, the width of the center hole is the same as that of the previous diaphragm, but the width of the diaphragm contacting the steel tube is reduced, thereby reducing the welding length by about 70% compared to the previous diaphragm. The in-plane strain of each specimen was analyzed when the same load was applied to the interior diaphragm through a simple tensile test. Using the general FEM program(ANSYS 19.2), the analysis was performed under the same conditions as the actual simple tensile test, and the load transfer between the improved diaphragm and the previous diaphragm was compared. When the width of the diaphragm is equal to or smaller than the flange width, stress is concentrated from the end of the diaphragm, and when the flange width is larger, stress is concentrated at the center.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.663-670
• /
• 2018

H13 tool steels are widely used as metallic mold materials due to their high hardness and thermal stability. Recently, many studies are undertaken to satisfy the demands for manufacturing the complex shape of the mold using a 3D printing technique. It is reported that the mechanical properties of 3D printed materials are lower than those of commercial forged alloys owing to micropores. In this study, we investigate the effect of microstructures and defects on mechanical properties in the 3D printed H13 tool steels. H13 tool steel is fabricated using a selective laser melting(SLM) process with a scan speed of 200 mm/s and a layer thickness of $25{\mu}m$. Microstructures are observed and porosities are measured by optical and scanning electron microscopy in the X-, Y-, and Z-directions with various the build heights. Tiny keyhole type pores are observed with a porosity of 0.4 %, which shows the lowest porosity in the center region. The measured Vickers hardness is around 550 HV and the yield and tensile strength are 1400 and 1700 MPa, respectively. The tensile properties are predicted using two empirical equations through the measured values of the Vickers hardness. The prediction of tensile strength has high accuracy with the experimental data of the 3D printed H13 tool steel. The effects of porosities and unmelted powders on mechanical properties are also elucidated by the metallic fractography analysis to understand tensile and fracture behavior.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.6
• /
• pp.629-639
• /
• 2018

In this study, the application of the single beam echosounder and multi beam echosounder was analyzed for the Youngsan river, from the Juksanbo to the Juksan bridge, length of 840m, width 230m and area $0.16km^2$. A single beam echosounder and a multi beam echosounder are mounted on an USV (Unmanned Surface Vessel), and each data is acquired. Then, TIN (Triangular Irregular Network) is created and the grid depth of 10m intervals is extracted. The grid depth of the single beam echo sounder and the grid depth of the multi beam echo sounder were overlapped to compare the two data. As a result of analysis using 5,024 data, the mean depth difference was 0.0319m and the standard deviation was 2.4095m. The river bed shape was similar to each other. If the multi-beam echo sounder is regarded as the standard, the volume difference of the stream is $161,882m^3$. With a multi-beam echo sounder installed, the operating distance increased by approximately 55% to 4595.85m, and the operating time increased by approximately 59% to approximately 47%.

• Korean journal of applied entomology
• /
• v.58 no.1
• /
• pp.9-13
• /
• 2019

Nematode-trapping fungi use various specialized traps to capture nematodes. A fungus that can capture nematodes in three dimensional adhesive networks was isolated from the soil around the root of Cucumis melo L. (Oriental melon) in Seongju, Korea. The conidiophores were found to be septate, hyaline, erect and $290-528(342.8){\mu}m$ high. It produces obovoid shape and 1-3 septate (commonly 2-septate) conidia with a size of $30.5{\times}20.3{\mu}m$. Molecular analysis of 5.8 S rDNA displayed 99% similarity to Arthrobotrys sinensis. On the basis of morphological, morphometric and molecular studies, the fungus was identified as A. sinensis. It is the first report in Korea which can be one of biological control resource of plant-parasitic nematode.

• Journal of Korean Society of Rural Planning
• /
• v.24 no.4
• /
• pp.135-146
• /
• 2018

A Visual landscape planning and management system has been introduced and implemented by each ministry so as to solve the problems of visual landscape destruction due to recognition on the value of natural landscape of beautiful territory and various development projects. At present, this system emphasizes the importance of the visual and perceptual aspect of the landscape however, there is a lack of techniques required for comprehensively predicting, evaluating, and managing it. Furthermore, sustainable landscape management after the completion of development projects has been inadequately carried out, as the focus has been only on consultation in the planning process of the development project in institutional performance. To this end, we presented objective and standardized criteria to predict and judge the effects of development projects on landscapes before project implementation. During the implementation of the development project, the influence of the visual landscape becomes accumulated in the construction progress stage. There is a need to identify the main viewpoints and to examine the continuous changes in the landscape-influencing factors, owing to the remarkable influences on the landscape, such as the change in the topography and the change caused by the artificial structure. During the stage of managing the influence on the visual landscape after the completion of the project, the influence on landscape should be monitored by measuring the change in the continuous landscape-influencing factors and determining the extent to which the actual reduction plan has been implemented. These processes should be performed continuously to maintain the quality of the visual landscape. The change in the landscape caused by the development project is shown to cause relatively greater visual damage than other factors composing the landscape owing to the influence of the artificial factors including the structure or the building. This shows that not only detailed examination of the visual impact before the development project but also continuous management is required during and after the development project. For this purpose, we derived eight landscape-influencing factors including form/shape, line, color, texture, scale/volume, height, skyline, and landscape control point. The proposed considering to be of high utilization in that it has a clear target of the landscape influencing factors.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.4
• /
• pp.455-478
• /
• 2019

In this paper, we conducted experimental investigation on the field applicability through the verification of reinforcement effect of the steel pipe reinforcement grouting using high strength steel pipe. SGT275 (formerly known as STK400) steel pipe is generally applied to the traditional steel pipe reinforcement grouting method. However, the analysis of tunnel collapse cases applying the steel pipe reinforcement grouting shows that there are cases where the excessive bending and breakage of steel pipe occur. One of the reasons causing these collapses is the lack of steel pipe stiffness responding to the loosening load of tunnels caused by excavation. The strength of steel pipe has increased due to the recent development of high strength steel pipe (SGT550). However, since research on the reinforcement method considering strength increase is insufficient, there is a need for research on this. Therefore, in this study, we conducted experiments on the tensile and bending strength based on various conditions between high strength steel pipe, and carried out basic research on effective field application depending on the strength difference of steel pipe through the conventional design method. In particular, we verified the reinforcement effect of high strength steel pipe through the measurement results of deformed shape and stress of steel pipe arising from excavation after constructing high strength steel pipe and general steel pipe at actual sites. The research results show that high strength steel pipe has excellent bending strength and the reinforcement effect of reinforced grouting. Further, it is expected that high strength steel pipe will have an arching effect thanks to strength increase.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.30-36
• /
• 2019

Traditional cell culture(2-dimensional) is the method that provide a nutrient and environment on a flat surface to cultivate cells into a single layer. Since the cell characteristics of 2D culture method is different from the characteristics of the cells cultured in the body, attempts to cultivate the cells in an environment similar to the body environment are actively proceeding in the industry, academy, and research institutes. In this study, we will develop a technology to fabricate micro-structures capable of culturing cells on surfaces with various curvatures, surface shapes, and characteristics. In order to fabricate the hemispheric plastic structure(thickness $50{\mu}m$), plastic preform mold (hereinafter as "preform mold") corresponding to the hemisphere was first prepared by injection molding in order to fabricate a two - layer structure to be combined with a flat plastic film. Then, thermoplastic polymer dissolved in an organic solvent was solidified on a preform mold. As a preliminary study, we proposed injection molding conditions that can minimize X/Y/Z axis deflection value. The effects of the following conditions on the preform mold were analyzed through injection molding CAE, [(1) coolant inlet temperature, (2) injection time, (3) packing pressure, (4) volume-pressure (V/P). As a result, the injection molding process conditions (cooling water inlet temperature, injection time, holding pressure condition (V / P conversion point and holding pressure size)) which can minimize the deformation amount of the preform mold were derived through CAE without applying the experimental design method. Also, the derived injection molding process conditions were applied during actual injection molding and the degree of deformation of the formed preform mold was compared with the analysis results. It is expected that plastic film having various shapes in addition to hemispherical shape using the preform mold produced through this study will be useful for the molding preform molding technology and cast molding technology.

• Journal of the Korea Convergence Society
• /
• v.10 no.7
• /
• pp.15-21
• /
• 2019

Research in detecting fake information gained a lot of interest after the US presidential election in 2016. Information from unknown sources are produced in the shape of news, and its rapid spread is fueled by the interest of public drawn to stimulating and interesting issues. In addition, the wide use of mass communication platforms such as social network services makes this phenomenon worse. Poynter Institute created the International Fact Checking Network (IFCN) to provide guidelines for judging the facts of skilled professionals and releasing "Code of Ethics" for fact check agencies. However, this type of approach is costly because of the large number of experts required to test authenticity of each article. Therefore, research in automated fake news detection technology that can efficiently identify it is gaining more attention. In this paper, we investigate fake news detection systems and researches that are rapidly developing, mainly thanks to recent advances in deep learning technology. In addition, we also organize shared tasks and training corpus that are released in various forms, so that researchers can easily participate in this field, which deserves a lot of research effort.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.7
• /
• pp.918-925
• /
• 2017

Multiple reflections on exterior equipment with complex shape on naval ships cause unexpectedly high Radar Cross Section (RCS) distributions, and the directions of reradiated electromagnetic waves are hard to predict. Therefore, the optimum arrangement of exterior equipments should be considered according to the Radar Absorbing Structure (RAS) method. In this paper, the optimum arrangement for exterior equipments was determined to reduce multiple reflections and RCS even with complex shapes. The sequential descending arrangement method was used to establish an optimum arrangement algorithm. An LCS-2 type model was selected for optimum exterior equipment arrangements. In order to reduce computational cost, RCS distributions and multiple reflection path analysis of exterior equipments was carried out to select exterior equipments for optimum arrangement, and an optimum arrangement was determined to find positions with minimum RCS values. Also, the RCS reduction effect was analyzed using detectable radar range.

• Journal of the Korea Convergence Society
• /
• v.10 no.7
• /
• pp.311-316
• /
• 2019

The purpose of this study is to analyze the preference of haircut according to demographic factors such as age, education, marital status, occupation, monthly income, and residence in order to contribute to the establishment of hair trends of Korean women living in the 4th industrial age. Respectively. After the questionnaire was distributed, 305 questionnaires were analyzed statistically. According to the results of the questionnaire survey, it was found that the higher the age group was, the higher the gradation pattern was, and the difference was statistically different according to the demographic characteristics (p<0.05). By analyzing the shapes and differences of female haircuts according to these demographic characteristics, we will contribute to the establishment of sophisticated and innovative hair trends of Korean women living in the era of the fourth industrial revolution. Through this study, we can find the most ideal hairstyle for Korean women and it will be a starting point for development of various new and creative hairstyles. It is also used as basic data for hairdressing education and it will be actively used as an objective index that can express women 's personality clearly.