• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.448-452
• /
• 2008

2-stroke marine diesel engine has generally one exhaust valve and three fuel injection nozzle which are key component for engine's performance and combustion. Fuel injection and exhaust valve driving system are driven by rotating of camshaft. Rotation of crank shaft drives the cam shaft through gear train that is composed of $3{\sim}4$ gear wheels. Gear column supporting the gear wheel has to bear against the dynamics forces by engine running as well as gearing forces. In this paper, structural analysis for engine structure and fatigue strength assessment of welded joint is shown. Repeatedly full cyclic simulation during one cycle is performed to investigate the structural behavior of engine. Fatigue analysis is carried out based on IIW using submodeling technique to obtain more detailed stress distribution.

• 대한기계학회논문집A
• /
• 제31권2호
• /
• pp.197-204
• /
• 2007

Fretting is a contact damage process that occurs between two contact surfaces. Fretting fatigue reduces fatigue strength of the material due to low amplitude oscillatory sliding and changes in the contact surfaces of strongly connected machine and structure such as bolt, key, pin, fixed rivet and connected shaft, which have relative slip of repeatedly extreme low frequency amplitude. In this research, the fretting fatigue behavior of 2024-T3511 and 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were experimentally estimated. Based on this experimental wort the following results were obtained: (1) A significant decrease of fatigue lift was observed in the fretting fatigue compared to the plain fatigue. The fatigue limit of 2024-T3511 aluminum alloy decreased about 59% while 7050-T7451 aluminum alloy decreased about 75%. (2) In 7050-T7451 specimen using ATSI4030 contact pad, crack was initiated more early stage than using 2024-T3511 contact pad. (3) In all specimens, oblique cracks were initiated at contact edge. (4) Tire tracks and rubbed scars were observed in the oblique crack region of fracture surface.

• 한국정밀공학회지
• /
• 제25권8호
• /
• pp.72-79
• /
• 2008

To meet demand of big capacity and high speed rotation for washing machine, more stress from bending and twisting are complexly loaded onto the shaft supporting the horizontal drum, causing problems in fracture strength and fatigue life. Shafting system is mainly divided into flange and shaft. Shaft and flange connected by inserting shaft serration into flange on the process of die casting. When the system is operating, the gap is formed between serration and flange. But, Serration has various design factors and the optimal values can't be easily determined. Using a design of experiment (DOE) based on the FEM (Finite Element Method), this study was performed investigating the interaction effect between the various design factors as well as the main effect of the each design factor under bending, twist and vibration and proposed optimum design using box-behnken method among response surface derived from regression equation of simulation-based DOE.

• 한국해양공학회지
• /
• 제13권2호통권32호
• /
• pp.74-82
• /
• 1999

Nowadays, the crank shaft motor vehicle has become essential as the important component. The machining precision was asked for manufacturing the shaft. They could be unstable in the quality by the conventional are welding. Both in-process quailty control and high reliability of the weld are the major concerns in applying friction wlding to the economical and qualified mass-production. No reliable nondestructive monitoring method is avaliable at present to determine the real-time evaluation of automatic production quality control for bar-to-bar friction welding of the crank shaft of O.D 24mm for motor vehicle. This paper, so that, presents the experimental examinations and statistical quantitative analysis of the correlation between the cumulative counts of acoustic emission(AE) during plastic deformation periods of the welding and the tensile strength and other properties of the bar-to-bar welded joints of O.D. 24mm shaft as well as the various welding variables, as a new approach which attempts finally to develop real-time quality monitoring system for friction welding, resulting in practical possiblility of real-time quality control more than 100% joint efficiency showing good weld with no micro structural defects.

• 대한기계학회논문집A
• /
• 제31권5호
• /
• pp.601-608
• /
• 2007

To meet demand of big capacity and high speed rotation for washing machine, more stress from bending and twisting are complexly loaded onto the shaft supporting the horizontal drum, causing problems in fracture strength and fatigue life. Shafting system is mainly divided into flange and shaft. Flange is located between the drum and shaft, transferring power from the shaft to drum, and acting as a supporter of the back of the drum. Because section of flange has various design factors according to configuration of flange, the optimum conditions can’t be easily determined. Using a design of experiment (DOE), this study was performed investigating the interaction effect between factors as well as the main effect of the each design factor under bending and twist and proposed optimum condition using center composition method among response surface derived from regression equation of simulation-based DOE.

• 한국기계가공학회지
• /
• 제9권6호
• /
• pp.7-15
• /
• 2010

Recently, with the high performance and efficiency of machine, there have been required the multi-functions in various machine parts, such as the heat resistance, the abrasion resistance and the stress resistance as well as the strength. Fatigue crack growth tests were carried out to investigate the fatigue characteristics of high carbon steel (SM53C) experienced by high-frequency induction treatment. The Cam nose part of the Automobile's Cam shaft is strongly bumped with rocker arm or valve-lift. Therefore abnormal wear such as unfair wear and early wear occur in the surface. This abnormal wear causes a defect that bad timing open and close actions of the engine valve happen in the combustion chamber so the fuel gas will be combustion imperfect. Therefore, the cam shaft demands high hardness and wear resistance. In this study, high frequency heat treatment has been accomplished while wear test for material SM53C.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.103-109
• /
• 2014

This paper represents the s-cam manufacturing process with the high-carbon steel like S45C using laser welding system. Laser welding of the high-carbon steel is generally difficult because of hardening of the weld zone. Also, existing s-cam manufacturing process, electric resistance welding system, have some problems like increase of production and development cost. To solve those problems, we are introduced the laser welding system with the pre-heating system for precision welding of s-cam with separated shaft and cam part. S-cam manufactured with optimum laser welding conditions is verified the performance like tensile strength, torsional strength and fatigue test. Strength and fatigue test results are described.

• 농업과학연구
• /
• 제49권2호
• /
• pp.269-284
• /
• 2022

The development of radish collectors has the potential to increase radish yields while decreasing the time and dependence on human labor in a variety of field activities. Stress and fatigue analyses are essential to ensure the optimal design and machine life of any agricultural machinery. The objectives of this research were to analyze the stress and fatigue of major components of a tractor-mounted radish collector under dynamic load conditions in an effort to increase the design dependability and dimensions of the materials. An experiment was conducted to measure the shaft torque of stem-cutting and transferring conveyor motors using rotary torque sensors at different tractor ground speeds with and without a load. The Smith-Watson-Topper mean stress equation and the rain-flow counting technique were utilized to determine the required shear stress with the distribution of the fatigue life cycle. The severity of the operation was assessed using Miner's theory. All running conditions produced more than 10⁷ of high cycle fatigue strength. Furthermore, the highest severity levels for motor shafts used for stem cutting and transferring and for transportation joints and cutting blades were 2.20, 4.24, 2.07, and 1.07, and 1.97, 3.81, 1.73, and 1.07, respectively, with and without a load condition, except for 5.24 for a winch motor shaft under a load. The stress and fatigue analysis presented in this study can aid in the selection of the most appropriate design parameters and material sizes for the successful construction of a tractor-mounted radish collector, which is currently under development.

• 한국주조공학회지
• /
• 제11권3호
• /
• pp.217-227
• /
• 1991

The present study was conducted to estimate the fatigue crack growth rate of the Mo-Ni alloyed ductile cast iron for the influence of austempering temperature and time. The fatigue crack growth rate was affected by retained austenite. Retained austenite volume were higher with the ductile cast irons which were austempered at $360^{\circ}C$ than austempered at $260^{\circ}C$, and the fatigue crack growth rate of the former was lower than that of the latter. Also, the fatigue growth rate of the former was the lowest at austempering for 1 hour and that of the latter was the lowest at austempering for 3 hours.

• 한국추진공학회지
• /
• 제3권1호
• /
• pp.104-117
• /
• 1999

복합재료는 비강성과 비강도의 우수성 때문에 첨단 산업분야에서 사용되고 있으며, 특히 낮은 비중으로 인한 중량감소 효과와 접착과 주조 둥에 의한 부품수의 감소효과 때문에 항공기와 수송기계분야에 널리 이용되고 있다. 복합재료의 이러한 장점들을 이용하여 항공기용 동력전달축과 자동차용 추진축에서 연구와 활용이 이뤄지고 있다. 본 연구에서는 우수한 진동 안정성을 갖는 복합재료 추진축을 설계하고 해석하였으며 이를 증명하기 위해 충격망치를 이용한 FFT해석기와 회전장비를 이용하는 두 가지 실험을 수행하였다.