• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.533-541
• /
• 2011

The redundant operation of a parallel AC to DC converter via a serial communication bus is presented. The proposed system consists of three isolated CUK power factor correction modules. The controller for each converter is a dsPIC30F6010 microcontroller while a RS485 communication bus and the clock signal are used for synchronizing the data communication. The control strategy of the redundant operation relies on the communication of information among each of the modules, which communicate via a RS485 serial bus. This information is received from the communication checks of the converter module connected to the system to share the load current. Performance evaluations were conducted through experimentation on a three-module parallel-connected prototype, with a 578W load and a -48V dc output voltage. The proposed system has achieved the following: the current sharing is quite good, both the transient response and the steady state. The converter modules can perform the current sharing immediately, when a fault is found in another converter module. In addition, the transient response occurs in the system, and the output voltages are at their minimum overshoot and undershoot. Finally, the proposed system has a relatively simple implementation for the redundant operation.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1013_1014
• /
• 2009

In this paper, the electrical interfaces used in between COMS satellite bus and Ka-band communication payload are analyzed to verify the robustness of data bus. The purpose of the serial data bus of satellite is to allow serial data transfer between one bus controller or source equipment to several user terminals or slave equipments. A serial data bus in COMS satellite is mainly used for Channel Amplifier and Digital Control Unit of Ka-band Payload.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제31권10A호
• /
• pp.996-1002
• /
• 2006

USB(Universal Serial Bus) is one of the most popular communication interfaces. When USB is used in an extended range, especially configurating In-home network by connecting multiple digital devices each other, USB interface uses the bandwidth in the way of TDM (Time Division Multiplexing) so that the bottleneck of bus bandwidth can be brought. In this paper, the more effective usage of bus bandwidth to overcome this situation is introduced.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2499-2502
• /
• 2005

Universal Serial Bus (USB) is one of the most popular communication interfaces. When USB is used in more extended range, especially configuring home network by connecting multiple digital devices each other, USB interface uses the bandwidth in the way of Time Division Multiplexing (TDM) so that the bottleneck of bus bandwidth can be brought under the heavy traffic. In this paper, the more effective usage of bus bandwidth to overcome this situation is introduced. Basically, in order to realize the system for transferring real-time moving picture data among digital information devices, we analyze USB transfer types and descriptors and introduce the method to enhance the detailed performance of isochronous transfer that is one of USB transfer types.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.195-197
• /
• 2006

In this paper, an interface unit is designed to efficiently monitor transmission data in Controller Area Network(CAN)-based control systems. The CAN uses a serial multi master communication protocol that efficiently supports distributed real-time control with a very high level of data integrity, and communication speeds of up to 1Mbps. The interface unit is composed of a DSP controller which collects data on the CAN bus and transfers data to a personal computer via serial communication to save and display of interesting signals. The experimental system consists of three DSP controllers which represent electronic control units of a vehicle, an interface unit for analysing the data on the bus, and a graphic monitoring program coded on the Windows platform. The validity and the effectiveness of the proposed simple type of CAN interface unit are shown through the experimental results.

• Journal of IKEEE
• /
• 제26권3호
• /
• pp.437-444
• /
• 2022

This paper proposes a CRC error verification method for SPI and I2C buses of automotive semiconductors. In automotive semiconductors, when an error occurs in communication and an incorrect value is transmitted, fatal results may occur. Unlike LIN communication and CAN communication, in communication such as SPI and I2C, there is no frame for detecting an error, so some definitions of new standards are required. Therefore, in this paper, the CRC error detection mode is newly defined in the SPI and I2C communication protocols, and the verification is presented by designing it in hardware.

• ETRI Journal
• /
• 제32권5호
• /
• pp.713-721
• /
• 2010

E-textile technology has earned a great deal of interest in many fields; however, existing wearable network protocols are not optimized for use with conductive yarn. In this paper, some of the basic properties of conductive textiles and requirements on wearable personal area networks (PANs) are reviewed. Then, we present a wearable personal network (WPN), which is a four-layered wearable PAN using bus topology. We have designed the WPN to be a lightweight protocol to work with a variety of microcontrollers. The profile layer is provided to make the application development process easy. The data link layer exchanges frames in a master-slave manner in either the reliable or best-effort mode. The lower part of the data link layer and the physical layer of WPN are made of a fabric serial-bus interface which is capable of measuring bus signal properties and adapting to medium variation. After a formal verification of operation and performances of WPN, we implemented WPN communication modules (WCMs) on small flexible printed circuit boards. In order to demonstrate the behavior of our WPN on a textile, we designed a WPN tutorial shirt prototype using implemented WCMs and conductive yarn.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2006년도 하계학술대회
• /
• pp.87-90
• /
• 2006

Nowadays, we can enjoy access to high speed network and advanced services of convergence between broadcasting and communication anywhere and anytime through a ubiquitous computing. So, now digital convergence devices come out constantly. These devices are required faster network environment for high speed data processing than before. In this paper, we describe the design of InfiniBnad network adapter, which is included two FPGA chipsets. When this adapter is installed to Digital Convergence Platform (DCP) network performance will be improved. The adapter includes 12channel serial ports for external communication and internally, uses PCI-Express bus. We have finished the test of high speed serial based network adapter through composing complete InfiniBand network and applied fabric management software. So, we have verified that it can be applied on DCP environment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제18권4호
• /
• pp.839-847
• /
• 2014

A recent major development in computer technology is the advent of the wearable computer system that is based on human-centric interface technology trends and ubiquitous computing environments. Wearable computer systems can use the wireless universal serial bus (WUSB) that refers to USB technology that is merged with WiMedia PHY/MAC technical specifications. In this paper, we focus on an integrated system of the wireless USB over the wireless body area networks (WBAN) for wireless wearable computer systems supporting U-health services. To construct the WUSB over WBAN communication systems, we propose a WBAN beaconing structure to assign WUSB communication periods. In the proposed structure, WUSB uses private periods of WBAN. In our performance evaluations, we compare theoretical results and simulation results about throughputs of WUSB under various WBAN channel occupations to evaluate the effectiveness of proposed structure in WUSB over WBAN communications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제9권1호
• /
• pp.88-94
• /
• 2005

This paper presents the design and implementation of a receiver operating between a rotary machine encoder and DSP. The receiver connects with the encoder using 1 bit serial data and DSP using 16 bits bus line. The receiver and encoder use the different operating frequency each other. We suggest a new apparatus and method of synchronized code for header detection in 1bit serial communication. The system operating frequency can be changed into 20MHz or 60MHz by using the external port such as 'clk_select'.