• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.388-394
• /
• 2015

The inrush current of a large inductive load can be reduced with a soft starter; however, the large inrush current caused by simultaneous bulk starts (SBSs) cannot be effectively reduced. In order to reduce the high inrush current and voltage sag owing to the SBSs of large capacity inductive loads within a power network, a novel hybrid sequential start control system is proposed, implemented on embedded systems, and evaluated with a testbed in this study. From the experimental and simulation results of the proposed control system, the inrush current could be effectively restricted below the maximum current capacity of a power distributing board. Moreover, with the proposed system, power cost typically dictated by the peak power consumption can be fairly reduced, and the quality of the power system connected to the inductive loads can be efficiently increased.

• 전기전자학회논문지
• /
• 제16권2호
• /
• pp.109-115
• /
• 2012

유도성 부하 네트워크의 기동에 의한 순간전압강하 및 기동전류 감쇄를 위해, TRIAC PWM 모듈과 순차기동시스템으로 구성된 제어시스템을 제안한다. 에어컨 컴프레서와 같은 대용량 유도성 부하의 기동시 발생하는 높은 순간전압강하와 기동전류를 최소화하기 위해 TRIAC PWM 모듈이 개발되었다. 대용량 유도성 부하 네트워크에서 부하의 동시 기동을 방지하는 순차기동시스템을 설계, 제작하였다. 제안된 제어시스템의 시험결과에 따르면, 본 시스템을 적용한 대용량 유도성 부하의 기동에 따른 배전계통의 순간전압강하 및 기동전류가 관련 국제규격을 효과적으로 만족시킬 수 있으며, 유도성 부하들의 동시 기동 문제 또한 효과적으로 해결할 수 있다. 제안된 시스템을 이용하면 최대전력소모량에 근거하여 부과되는 전력비용을 절감하거나, 유도성 부하 네트워크가 연결된 동일 배전 계통의 전력품질 안정화에도 크게 기여할 것으로 기대된다.

• Smart Structures and Systems
• /
• 제26권5호
• /
• pp.545-558
• /
• 2020

A design method of a Multiple Tuned Mass Damper (MTMD) system is presented for wind induced vibration control of a cable-supported roof structure. Modal contribution analysis is carried out to determine the dominating modes of the structure for the MTMD design. Two MTMD systems are developed for two most dominating modes. Each MTMD system is composed of multiple TMDs with small masses spread at multiple locations with large responses in the corresponding mode. Frequencies of TMDs are distributed uniformly within a range around the dominating frequencies of the roof structure to enhance the robustness of the MTMD system against uncertainties of structural frequencies. Parameter optimizations are carried out by minimizing objective functions regarding the structural responses, TMD strokes, robustness and mass cost. Two optimization approaches are used: Single Objective Approach (SOA) using Sequential Quadratic Programming (SQP) with multi-start method and Multi-Objective Approach (MOA) using Non-dominated Sorting Genetic Algorithm-II (NSGA-II). The computation efficiency of the MOA is found to be superior to the SOA with consistent optimization results. A Pareto optimal front is obtained regarding the control performance and the total weight of the TMDs, from which several specific design options are proposed. The final design may be selected based on the Pareto optimal front and other engineering factors.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2004년도 춘계 학술발표회 논문집
• /
• pp.197-200
• /
• 2004

Compared to conventional flame combustion, catalytic combustion had the advantage of oxidation of V.O.C. gas which was high voluminous, low caloric mixture flow. However, the temperature of mixture gas should be over the one of catalytic reaction start and the control of reaction on the catalytic surface tends to be vulnerable. To overcome these obstacles, composition of both catalytic combustor and heat exchanger was devised and named the sequential catalytic combustion system. In this system, only trigger unit needed preheating process for transient starting time. Once trigger unit was ignited, the next unit w3s supplied heat to ignite from that and same process was performed to the last one sequentially. When it come to steady state, whole mixture gas was oxidated at each unit simultaneously and preheating for trigger unit was not needed any more. System of 100 kcalh/hr capacity was devised and operated successfully.

• 조명전기설비학회논문지
• /
• 제19권2호
• /
• pp.114-123
• /
• 2005

서보 설비를 위한 순차적 파라미터 자동 튜닝 알고리즘을 갖는 영구자석 동기전동기(Permanent Magnet Synchronous Motor: PMSM)의 비선형 속도 제어 기법이 제시된다. 비선형 제어 방식은 시스템 파라미터와 부하상태가 정확하게 일치하지 않는 경우 만족스러운 성능을 줄 수 일다. 최근에 향상된 속도 제어 성능을 위해 적응형 기법, 슬라이딩 모드 제어, 및 관측기에 기반 한 기법들이 제안되었다. 하지만, 이 방법들은 관성의 큰 변화, 속도의 빠른 과도 특성 및 샘플링 주기 증가와 같은 특정한 조건에서 더 이상 만족스러운 성능을 제공하지 않는다. 일반적으로, 속도 동특성에 영향을 주는 주요 파라미터를 동시에 추정하기는 쉽지 않다. 이를 해결하기 위해 설치 및 기동시 전동기 주요 파라미터를 시간 구간 별로 나누어 자동으로 추정하는 순차적 파라미터 튜닝 알고리즘이 제안된다. 제안된 방식이 DSP TMS320C31을 이용하여 구현되고 유용성이 시뮬레이션과 실험을 통해 입증된다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.249-251
• /
• 2008

In Factory Automation(FA) used by Programmable Logic Controller(PLC), Ladder Diagram(LD) is the most widely utilized and plays an important role in industrial control system. But recently, the study about Sequential Function Chart(SFC) is performed actively. When we program by SFC, generally, we design one routine from start to end. This method is difficult to design block control system, and we often make mistakes. In this paper, we propose the method that we design block control system and we analysis the difference of the method used this paper from conventional method.

• 조명전기설비학회논문지
• /
• 제20권4호
• /
• pp.49-55
• /
• 2006

PLC를 사용한 공정제어에서 일반적으로 LD 언어로 가장 많이 프로그램한다. 그러나 최근에는 SFC 언어에 대한 연구가 활발히 이루어지고 있다. PLC를 사용한 공정제어에서 SFC 언어로 프로그램할 때는 처음부터 마지막까지 하나의 루틴으로 설계하는 것이 일반적이다. 이러한 방법은 설계하기가 무척 힘들고, 흔히 실수하는 경우가 많다. 본 논문에서는 개별 서브시스템을 설계하고, 각 서브시스템을 결합하는 방법을 제안하였고, 실례를 통해 그의 타당성을 확인하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.1021-1022
• /
• 2006

In industrial control system used by Programmable Logic Controller(PLC), Ladder Diagram(LD) is the most widely utilized and plays an important role in industrial control system. But recently, the study about Sequential Function Chart(SFC) is performed actively. When we program by SFC, generally, we design one routine from start to end. This method is difficult to design, and we often make mistakes. In this paper, we propose the method that we compose each sub-system after we design each sub-system, and we analysis the difference of the method used this paper from conventional method.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2006년도 춘계학술대회 논문집
• /
• pp.462-466
• /
• 2006

In industrial control system used by Programmable Logic Controller(PLC), Ladder Diagram(LD) is the about widely utilized and plays an important role in industrial control system. But recently, the study about Sequential Function Chart(SFC) is performed actively. When we program by SFC, generally, we design one routine from start to end. This method is difficult to design, and we often make mistakes. In this paper, we propose the method that we compose each sub-system after we design each sub-system and we analysis the difference of the method used this paper from conventional method.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.224-237
• /
• 1995

An ECU(Electronic Control Unit) with 16 bit microcomputer has been developed. This system includes hardware and software for more precise control on fuel injection, ignition timing, and idle speed. This control system employs an air flow sensor of the hot wire type, a direct ignition system, an idle speed control system using a solenoid valve, and a crank angle sensor. Especially, the crank angle sensor provides two separate signals: One is the position signal(POS) which indicates 180 degree pulses per revolution, and the other is the reference signla(REF) that represents each cylinder individually. The conventional engine control system requires at least two engine revolutions in order to identify the cylinder number. However, the developed engine control system can recognize the cylinder number within a quarter of an engine revolution. Therfore, the developed engine control system has been able to control fuel injection and ignition timing more quickly and accurately, Furthermore, the number of misfire reduces during the cold start.