• Journal of the Korean Society for Railway
• /
• v.19 no.3
• /
• pp.397-407
• /
• 2016

This study analyzed the efficiency change and the factors affecting productivity change for the six railway operation corporations that are local public enterprises; study was performed with the DEA-CCR Model and Malmquist Productivity Index, using data collected from 2010 to 2014. Since it was not feasible to collect data on the operating expenses and the number of employees of each of the lines, the efficiencies of each operation corporation were analyzed by integrating the operation corporations, and the Malmquist Productivity Index was used to investigate the trend of the periodical productivity change. Average efficiency for urban railway operation corporations was found to be higher in the case of the bigger corporations. In 2014, the Seoul Metro and the Daejeon Metropolitan Express Transit Corporations were analyzed and found to be the most efficient operation corporations. The Malmquist Productivity Index was used to determine the periodical change; the average MPI was 1.06, with a continuous increase of productivity. The analysis showed that changes of technology were generally more obvious than change of technology efficiency for all six operation corporations.

• Tunnel and Underground Space
• /
• v.18 no.6
• /
• pp.465-479
• /
• 2008

For the quantitative identification of rock behavior in shallow tunnels, we recommend using the rock behavior index (RBI) by the analytic hierarchy process (AHP) and the Rock Engineering Systems (RES). AHP and RES can aid engineers in effectively determining complex and un-structured rock behavior utilizing a structured pair-wise comparison matrix and an interaction matrix, respectively. Rock behavior types are categorized as rock fall, cave-in, and plastic deformation. Seven parameters influencing rock behavior for shallow depth rock tunnel are determined: uniaxial compressive strength, rock quality designation (RQD), joint surface condition, stress, pound water, earthquake, and tunnel span. They are classified into rock mass intrinsic, rock mass extrinsic, and design parameters. An advantage of this procedure is its ability to obtain each parameter's weight. We applied the proposed method to the basic design of Seoul Metro Line O and quantified the rock behavior into RBI on rock fall, cave-in, and plastic deformation. The study results demonstrate that AHP and RES can give engineers quantitative information on rock behavior.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.12
• /
• pp.6098-6104
• /
• 2012

Currently, dozens of CCTVs are widely used in railway station for monitoring passengers in danger and security areas. The most frequent accidents occur at the platform area where passengers boarding the train. However, It is almost impossible that station operator monitors dozens of CCTV screens and recognizes immediately accidents and handle them. Therefore, railway platform monitoring system using image processing technology which automatically detects platform accidents is needed, and in order to that, preferentially, accurate determination of train state in the platform is required. In the paper, we propose train state detection algorithm for vision based railway platform monitoring system. the proposed algorithm determines four different states i.e. trains approach(IN), departure(OUT), stop(ON), and empty(OFF) of the train, in the platform. To evaluate the proposed algorithm, we present the train detection results for the Seoul Metro Line 4 Dongjak and Namtaeryeong Station.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.2
• /
• pp.1-17
• /
• 2018

The living lab is a user-participatory innovation space where users can solve problems by themselves. Living Lab members are able to participate in all aspects of product development from technology conception. In this study, to prevent pedestrian accidents, auto-image sensing signal system was developed in Jeonju City, using the Living Lab method. In addition, we measured effectiveness of the auto-image sensing signal system with respect to pedestrian waiting time, pedestrian and driver signal violation, and pedestrian jaywalking. It was also compared the measures before installation, after installation and after applying Living Lab method. As a result, all of the three measures of effectiveness appeared to be more effective after Living Lab than after installation. Overall, this study is very significant in that it is the first case where the living lab is applied in transportation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.5
• /
• pp.487-495
• /
• 2014

In this study, in order to suggest the design method for supports in the room-and-pillar underground structure, the case study was carried out. In the case study, shape of rock pillar and room was mainly considered. From the analysis, a displacement at the roof, the maximum principle stress and plastic state were examined. To optimize variables in the case study, cases from the Seoul metro station were analyzed, then a target depth of the underground structure and ground conditions were determined. And the height of rock pillar and room were chosen from the assumed purpose of underground space, i.e. living/office and warehouse. Total cases of analysis was 180 cases including 3 types of ground condition, 5 types of rock pillar and 6 types of roof span. It is expected that results from analysis can be used to determine the installation of support in room-and-pillar underground structure with stability, utilization efficiency of underground space and applicability of vehicles.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.369-375
• /
• 2020

The section of this study is the geological vulnerable zone where groundwater leakage occurred through the tunnel barrier during excavation of the shield tunnel boring machine(TBM) for the construction of the electric power unit. Therefore, a Three D imensions(3D) numerical analysis was performed to analyze the actual situation from before construction to the time when the change in groundwater level occurred, and to reflect the surrounding ground conditions based on the observed change in groundwater level during construction. As a result of the study, the correlation between groundwater level change and tunnel construction around the site was identified. Therefore, it was similar to the measurement result of groundwater level at the target ground. The amount of groundwater discharge to the entrance of the tunnel construction was also similar to the actual measured result, and the numerical analysis method and modeling in this study were analyzed to reflect the site conditions.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.335-340
• /
• 2020

The purpose of this study was to compare the dynamic behavior of STEDEF track that of the sleeper floating track on urban rapid transit according to replacing the resilience pads and analyze the necessity of replacing the resilience pads experimentally. It was analyzed that the uniformity of the track support stiffness could be secured by replacing the used resilience pads with new resilience pads. Therefore, by replacing the used resilience pads, the measured track impact factor was found to be dramatically reduced below the track design standard, and it was analyzed that the track support stiffness could be restored to the design value. As a results, it is possible to restore track support stiffness to the design value and reduce track impact factor by replacing timely resilience pads, which is important to securing durability and improving service life of track components.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.347-352
• /
• 2020

In this study, the variation of track impact factor according to the spring stiffness change rate of sleeper resilience pad was analyzed based on field measurements. In addition, the correlation between field measurement results and 7 million fatigue test results was verified. The fatigue effect diagram of the sleeper resilience pads was presented considering the nonlinear deterioration characteristics of the sleeper resilience pads used for the STEDEF track. Based on the field measurement results, the nonlinear characteristics of the track impact factor for the spring stiffness change rate over 30% of sleeper resilience pad on the track impact factor-track support stiffness diagram were analyzed to be consistent with the fatigue test results.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1097-1106
• /
• 2007

Rail provides running tract for train and broadly and widely conveys the weight of the train exerted from the train wheels that the rail directly supports onto the cross tie and roadbed, and supports the cross-sectional pressure exerted by centrifugal force at curvatures. That is, stationary rail provides surface on which dynamic train runs and guarantees cross-sectional resistance to enable the vertical snake motion of the train wheels as well as to maintain lateral force at curvatures. Rail provides running surface on which train wheels can run smoothly, and secures vertical and lateral force. However, it undergoes continuous destructive reactions (wearing and damages) and abrasion of the cladding by the train wheels. It is obvious that wearing will result when two metal parts act against each other. However, occurrence of abnormal wearing such as rapid wearing of the rail side due to complex generation of various mechanisms at the contact surface between the rail and train wheel flange. It is not easy to simply examine the causes of occurrence of abnormal wearing of rail and train wheel flange. Although countless number of academicians and specialists are conducting researches on abnormal wearing of rail and vertical wearing of train wheels, I believe it is too early to argue on pros and cons due to insufficiency of officially verified information on the issue. This review will be focusing on the examples of repairs that reduced the generation of abnormal wearing of rail by reviewing and improving characteristics of wearing and slack, speed of the train and cant as well as status of lubricator by choosing the compound curves present in the section between the $Anguk{\sim}Jongno3-ga$ Stations of the Route No. 3 among the compound curve tracks of the Seoul Metro Routes No. 3 & 4 at which abnormal wearing is generated continuously.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1852-1857
• /
• 2007

Since the introduction of the subway, remarkable progress has been made so as to be able to produce a Korean standard electric car, but it is rather regretful that an engineer who is not aware of laws on a railroad or involved in a railroad designed a electric car. In the future, the electric cars with up-to-date technology must be introduced, but there are many difficulties in such introduction. For example, the operation of simultaneously moving and running scores of subway trains must comply with Regulation on Railroad Train Operation, so, close examination of these problems is required. The existing electric car, as does a motorcar, varies a little with makers in the type and characteristics. This paper is intended to discuss about the device and measures for reinforcing a function of Daewoo GEC electric car that was introduced by technical tie-up from England, which accounts for the most ratio in this field