• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.869-875
• /
• 1997

Bi based superconducting thin films were fabricated by 4-target RF magnetron sputtering using the method of controlling the on-off time. These thin films showed better crystal structures. The ratio of Cu/Bi decreased but the critical temperature increased with increasing the temperature of the substrate. High temperature phase low temperature of the substrate. High temperature phase low temperature phase and semiconducting phase can be formed by controlling the on-off time of the shutter respectively.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.375-381
• /
• 2002

N-type ${\beta}-FeSi_2$ with a nominal composition of $Fe_{0.98}Co_{0.02}Si_2$ powders has been produced by mechanical alloying process and consolidated by vacuum hot pressing. As-milled powders were of metastable state and fully transformed to ${\beta}-FeSi_2$ phase by subsequent isothermal annealing. However, as-consolidated $Fe_{0.98}Co_{0.02}Si_2$ consisted of untransformed mixture of ${\alpha}-Fe_2Si_ 5$ and $\varepsilon$-FeSi phases. Isothermal annealing has been carried out to induce the transformation to a thermoelectric semiconducting ${\beta}-FeSi_2$ phase. The transformation behavior of ${\beta}-FeSi_2$ was investigated by utilizing DTA, a modified TGA under magnetic field, SEM, and XRD analyses. Isothermal annealing at $830^{\circ}C$ in vacuum led to the thermoelectric semiconducting ${\beta}-FeSi_2$ phase transformation, but some residual metallic $\alpha$ and $\varepsilon$ phases were unavoidable even after prolonged annealing. Thermoelectric properties were remarkably improved by isothermal annealing due to the transformation from metallic $\alpha$ and $\varepsilon$ phases to semiconducting phases.

• Korean Journal of Materials Research
• /
• v.14 no.3
• /
• pp.218-223
• /
• 2004

P-type $\beta$-FeSi$_2$ with a nominal composition of $Fe_{0.92}Mn_{0.08}Si_2$ powders has been produced by mechanical alloying process. As-milled powders were spray dried and consolidated by atmospheric plasma thermal spraying as a rapid sintering process. As-milled powders were of metastable state and fully transformed to $\beta$-$FeSi_2$ phase by subsequent isothermal annealing. However, as-thermal sprayed $Fe_{0.92}Mn_{0.08}Si_2$ consisted of untransformed mixture of $\alpha$-$Fe_2Si_{5}$ and $\varepsilon$-FeSi phases. Isothermal annealing has been carried out to induce transformation to the thermoelectric semiconducting $\beta$-$FeSi_2$ phase. Isothermal annealing at $845^{\circ}C$ in vacuum gradually led to the thermoelectric semiconducting $\beta$-$FeSi_2$ phase transformation, but some residual metallic $\alpha$ and $\varepsilon$ phases were unavoidable even after prolonged annealing. Thermoelectric properties of $\beta$-$FeSi_2$ materials before and after isothermal annealing were evaluated. Seebeck coefficient increased and electric conductivity decreased with increasing annealing time due to the phase transition from metallic phases to semiconducting phases. Thermoelectric properties showed gradual increment, but overall properties appeared to be inferior to those of vacuum hot pressed specimens.

• 전기의세계
• /
• v.26 no.1
• /
• pp.82-86
• /
• 1977

Semiconducting Barium Titanate shows resistivity anomaly near the transition temperature 120.deg. C. Its transition temperature decreases about 6-7.deg. C per 1 mole % SnO$_{2}$, which is likely to compose (BaSb) (TiSn) $O_{3}$ structure by making Sn$^{+4}$ ions occupy Ti$^{+4}$ ion sites. Grain boundories, whose existance is the cause of having high resistivity in Semiconducting BaTiO$_{3}$ disappear due to the spontaneous polarization below the transition temperature, and it is believed that the phase transition makes semiconducting BaTiO$_{3}$ have resistivity anomaly at certain temperature. Temperature and frequency dependencies of resistivity are also investigated for practical application.ion.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.632-637
• /
• 2000

Thermoelectric conversion properties of commercial Fe-Si2 and Fe-Si alloy ingots prepared by RF inductive furnace were investigated. As sintering temperature increased, density of the specimen increased and the phase transformation from metallic phases ($\varepsilon$-FeSi, ${\alpha}$-Fe2Si5) to semiconducting phase (${\beta}$-FeSi2) occurred more effectively. The FeSi phase was detected even after 100hrs of annealing treatment. For the Fesi1.95∼FeSi2.05 specimens prepared by RF inductive furnace, the thermoelectric property improved as the composition of the specimen approached to stoichiometric composition FeSi2. Electrical conductivity of the specimen increased with increasing temperatures showing typical semiconducting behavior. From the electrical conductivity measurements, activation energy in the intrinsic region (above about 700 K) was calculated to be approximately 0.46 eV. In spite of non-doping, the Seebeck coefficient for every specimen exhibited p-type conduction due to Si deficiency. Its maximum value was located at about 475 K, and then decreased abruptly with increasing temperatures. The power factor was governed by the Seebeck coefficient of the specimen more significantly than by electrical conductivity.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2017.05a
• /
• pp.163-163
• /
• 2017

• Bulletin of the Korean Chemical Society
• /
• v.11 no.5
• /
• pp.464-466
• /
• 1990

A ternary Zintl phase material of the formula $K_2Ga_2Sb_4$ has been prepared directly from reaction of the elements following a high temperature procedure. The compound consists of potassium ions and planar ribbons of $(Ga_2Sb_4^{-2})_{\infty}$ consisting of five membered $[Ga_2Sb_3]$ rings bridged by Sb atoms. The variable temperature specific resistivity measurements show the material to be an intrinsic semiconductor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.10
• /
• pp.731-735
• /
• 2013

YBCO thin films on $SiO_2$/Si substrate were fabricated by spin-coaing of an alkoxide-derived precursor and heat treatment. The structural and electrical properties of the YBCO films were investigated as functions of annealing temperature at $600{\sim}800^{\circ}C$. Although YBCO single phase was not synthesized, dense films of YBCO matrix phase and minor second phases have been successfully fabricated at the annealing temperatures of $650{\sim}800^{\circ}C$. Thickness and temperature coefficient of resistance (TCR) of YBCO thin films with annealing temperature of $750^{\circ}C$ were 0.31 ${\mu}m$ and $-2.92%/^{\circ}C$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.28 no.7
• /
• pp.525-530
• /
• 1991

The effects of 0.15mol% Y2O3 doped semiconducting (Ba1-xPbx)TiO3 ceramics with 0.5 mol% Pb5Ge3O11 as sintering additives have been investigated as function of Pb contents (from 0.05 mol to 0.3 mol) and sintering temperatures (from 1050$^{\circ}C$ to 1200$^{\circ}C$). As the Pb content increases in the (Ba1-xPbx)TiO3 system, the size and resistance of the grain increase but the capacitance of the grain boundary decreases due to the formation of liquid phase during the sintering. And with increasing the sintering temperatures, the resistance of the grain decreases but the capacitance of the grain boundary increases. The PTCR effects decrease with increasing the Pb content and the sintering temperature.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.349-352
• /
• 1989

Poling piezoelectric ceramic-polymer composites with 0-3connectivity is difficult because of the high dielectric constant of most of the ferroelectric filler materials, and the high resistivity of the polymer matrix. To aid in poling this type of composite, conductivity of the polymer phase can be controlled by adding small amount of a semiconductor phase such as germanium, carbon or silicon. In this study, flexible piezoelectric composites of $PbTiO_3$ powder and Eccogel polymer were developed using small amounts of a semiconducting phase. These composites were poled rapidly at low voltages, resulting in properties superior to composites prepared without a conductive phase. The effect of addition of various conductive phase with different volume percentage on the dielectric and piezoelectric properties of the composite are discussed here.