• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.252-253
• /
• 2021

In this study, butyl rubber, which is the main material constituting the self-adhesive butyl rubber waterproofing sheet, was mixed with reclaimed rubber, and tensile strength, tear strength, peeling resistance strength, and adhesion strength were measured for sample prepared by mixing ratio. As a result, it was confirmed that peeling resistance strength and adhesion strength decreased as the reclaimed rubber content increased, and tensile strength and tear strength did not change significantly.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.1
• /
• pp.55-60
• /
• 2010

Purpose: The shrinkage of dental resin cement may cause several clinical problems such as distortion that may jeopardize the accurate fit to the prepared tooth and internal stress within the restorations. It is important to know the polymerization shrinkage-strain of dental resin cement to reduce clinical complications. The purpose of this study was to investigate the polymerization shrinkage-strain kinetics of six commercially available dental resin cements. Material and methods: Three self-cure resin cements (Fujicem, Superbond, M-bond) and three dual-cure resin cements (Maxcem, Panavia-F, Variolink II) were investigated. Time dependent polymerization shrinkage-strain kinetics of the materials were measured by the Bonded-disk method as a function of time at $23^{\circ}C$, with values particularly noted at 1, 5, 10, 30, 60, 120 min after mixing. Five recordings were taken for each materials. The data were analyzed with one-way ANOVA and Scheffe post hoc test at the significance level of 0.05. Results: Polymerization shrinkage-strain values were 3.72%, 4.19%, 4.13%, 2.44%, 7.57%, 2.90% for Fujicem, Maxcem, M bond, Panavia F, Superbond, Variolink II, respectively at 120 minutes after the start of mixing. Panavia F exhibited maximum polymerization shrinkage-strain values, but Superbond showed minimum polymerization shrinkage-strain values among the investigated materials (P < .05). There was no significant differences of shrinkage-strain value between Maxcem and M bond at 120 minutes after the start of mixing (P > .05). Most shrinkage of the resin cement materials investigated occurred in the first 30 minutes after the start of mixing. Conclusion: The onset of polymerization shrinkage of self-cure resin cements was slower than that of dual-cure resin cements after mixing, but the net shrinkage strain values of self-cure resin cements was higher than that of dual-cure resin cements at 120 minutes after mixing. Most shrinkage of the dental resin cements occurred in the first 30 minutes after mixing.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.35-42
• /
• 2014

Thermal analysis properties and adhesive properties of self-healing agents were evaluated through differential scanning calorimetry, reaction heat measurement, and adhesive shear test. D1E0, D3E1, D1E1, D1E3, and D0E1, depending on the mixing ratio of DCPD and ENB, were considered as self-healing agents. The amount of Grubbs' catalyst, depending on the type of self-healing agents, was varied from 0.1 wt% to 1.5 wt%. In the case of DCPD, the polymerization reaction occurred faster and the stabilized adhesive strength increased as the amount of catalyst increased; however, a large amount of catalyst was required. ENB had excellent reactivity with a small amount of the catalyst; however, high reaction heat was observed at the early stage of polymerization. Thermal analysis properties and adhesive properties of self-healing agents can be controlled by varying a mixing ratio of DCPD and ENB. Among the self-healing agents used for this study, the D3E1 would be one of the most preferable candidates with regard to maximum adhesive strength, reaching time to maximum adhesive strength, stabilized adhesive strength, and reaction heat.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.1
• /
• pp.61-69
• /
• 2004

This paper describes numerical efforts to characterize the flame-holding and air-fuel mixing process of model SCRamjet engine combustor, where a hydrogen jet injected into a supersonic cross flow and in a cavity Combustion phenomena in a model SCRamjet engine, which has been experimentally studied at University of Queensland and Australian National University using a free-piston shock tunnel, was observed around separation region of upstream of the normal injector and inside of cavity. The results show that the separation region and cavity generates several recirculation zones, which increase the fuel-air mixing. Self ignition occurs in the separation-freestream and cavity-freestream interface.

• Korean Journal of Agricultural Science
• /
• v.47 no.4
• /
• pp.921-931
• /
• 2020

This study was carried out to determine the factor of a separating system according to the pepper varieties and the absence of a card cleaner system. The pepper varieties of Jeokyoung and AR-Legend were transplanted on November 20, 2019 and tested on March 18, 2020 with a harvesting speed of 0.2 m·s-1 for 10 pepper plants. The performance evaluation was determined by analyzing the separation efficiency of the peppers and the foreign matter mixing rate. The pepper harvester with a card cleaner showed a higher separation efficiency of the peppers compared to the pepper harvester without a card cleaner. The average separation efficiency of peppers on the pepper harvester with a card cleaner was higher at 13.5% for Jeokyoung and 1.9% for AR-Legend than that without a card cleaner. The mixing ratio of foreign materials on the pepper harvester with a card cleaner was lower at 8.7% and 2.5% for Jeokyoung and AR-Legend than that without a card cleaner, respectively. For the two-way ANOVA results according to the variety and the card cleaner, there was no effect on the separation efficiency of the peppers, but there was an effect on the foreign matter mixing rate.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.2
• /
• pp.5-11
• /
• 1974

Theoretical analysis is carried out for the beat frequency generation phenomena in the IMPATT diodes an4 the experimental studies are given in parrallel. The theory is based on the space charge modulation effect introduced to the multiplication process by the input signal. Computed results show that the beat frequency output power is linearly dependent upon the signal power and self oscillating power. Also the strong dependence of the output power with respect to the diode negative resistance is found and it turns out that the larger the negative resistance, the stronger the beat frequency output power. Experimental results show a good agreement with the theoretical values. Calculated conversion gain is about -0.4[db] at 10[GHz] and the experimental value shows -6.2[db] below this value. This difference between the theoretical and the experimental values is considered to be the results of the ineffective injection of signal power.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.55-61
• /
• 2022

There is a major interest in diagnostic technology for multiple cancers worldwide. In order to reduce the difficulty of cancer diagnosis, a liquid biopsy technology based on a microfluidic device using trace amounts of biofluids such as blood is being studied. And optical biosensing, which measures the concentration of analytes through fluorescence imaging using biofluids, requires various strategies to improve sensitivity, and specialists and equipment are needed to carry out these strategies. This leads to an increase in diagnostic and production costs, and it is necessary to develop a technology to solve this problem. In this paper, we design and propose a fluorescent multi-cancer diagnostic sensing platform structure that implements passive self-separation technology and molecular recognition activation functions by fluid mixing, only with the geometry and microfluidic phenomena of microchannels based on self-driven flow by capillary force. In order to check the parameters affecting the performance of the plasma separation part of the designed sensor, the hydrodynamic diameter of the channel and the viscosity of the fluid were set as variables to confirm the formation of plasma separation flow through simulation. And finally, we propose an optimal sensor platform structure.

• 한국연소학회:학술대회논문집
• /
• 2003.05a
• /
• pp.35-39
• /
• 2003

A numerical study is carried out to investigate combustion phenomena in a model SCRamjet engine, which has been experimentally studied at the Australian National University using a T3 free-piston shock tunnel. The Mach number is 3.8, the static pressure 110kPa and the static temperature 1100K in the main air flow. The fuel is hydrogen, which is injected in the cavity. Equivalence ratio is set to either 0.25 or 0.5 to access its effect on the fuel-air mixing combustion phenomena. The results show that the cavity generates several recirculation zones, which increase the fuel-air mixing. Self ignition occurs near the point of fuel injection. The flame is anchored by the cavity and generates the precombustion shock on the step. For a high equivalence ratio, the recirculation zones are bigger and the flame is present throughout the combustor.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1991.04a
• /
• pp.99-104
• /
• 1991

It is necessary to generalize the use for structural ALA Concrete in our country, as increasing in the need for the development of ALA and the use of ALA Concrete which is related with the diminution of the self load and foundation section of structure responding to the realistic requirement against the decrease of natural aggregate and the high-rising and large-sizing of structures. This little study, therefore intended to help in the mixing design of concrete by considering the fundamental properties of ALA Concrete used with expanded clay, which is considered by acopting the experimental factors such as unit cement content, water cement ratio and the rate of fine aggregate. By considering the results of this experiment, it has difficulty in getting expected slump with the unit water content of normal concrete because of the large absorption of lightweight aggregate, and because the weight of unit volume and specific gravity ALA Concrete are small it appears that the strength and Elastic Modulus of that are small too and that it is more ductile than normal concrete.

• Journal of Powder Materials
• /
• v.24 no.3
• /
• pp.229-234
• /
• 2017

We report on a simple and robust route to the spontaneous assembly of well-ordered magnetic nanoparticle superstructures by irreversible evaporation of a sessile single droplet of a mixture of a ferrofluid (FF) and a nonmagnetic fluid (NF). The resulting assembled superstructures are seen to form well-packed, vertically arranged columns with diameters of $5{\sim}0.7{\mu}m$, interparticle spacings of $9{\sim}2{\mu}m$, and heights of $1.3{\sim}3{\mu}m$ The assembled superstructures are strongly dependent on both the magnitude of magnetic field and the mixing ratio of the mixture. As the magnitude of the externally applied magnetic field and the mixing ratio of the mixture increase gradually, the size and interspacing of the magnetic nanoparticle aggregations decrease. Without an externally applied magnetic field, featureless patterns are observed for the ${\gamma}-Fe_3O_4$ nanoparticle aggregations. The proposed approach may lead to a versatile, cost-effective, fast, and scalable fabrication process based on the field-induced self-assembly of magnetic nanoparticles.