• Horticultural Science & Technology
• /
• v.33 no.5
• /
• pp.647-657
• /
• 2015

To investigate a method for calculation of the heating load for environmental designs of horticultural facilities, measurements of total heating load, infiltration rate, and floor heat flux in a large-scale plastic greenhouse were analyzed comparatively with the calculation results. Effects of ground heat exchange and infiltration loss on the greenhouse heating load were examined. The ranges of the indoor and outdoor temperatures were $13.3{\pm}1.2^{\circ}C$ and $-9.4{\sim}+7.2^{\circ}C$ respectively during the experimental period. It was confirmed that the outdoor temperatures were valid in the range of the design temperatures for the greenhouse heating design in Korea. Average infiltration rate of the experimental greenhouse measured by a gas tracer method was $0.245h^{-1}$. Applying a constant ventilation heat transfer coefficient to the covering area of the greenhouse was found to have a methodological problem in the case of various sizes of greenhouses. Thus, it was considered that the method of using the volume and the infiltration rate of greenhouses was reasonable for the infiltration loss. Floor heat flux measured in the center of the greenhouse tended to increase toward negative slightly according to the differences between indoor and outdoor temperature. By contrast, floor heat flux measured at the side of the greenhouse tended to increase greatly into plus according to the temperature differences. Based on the measured results, a new calculation method for ground heat exchange was developed by adopting the concept of heat loss through the perimeter of greenhouses. The developed method coincided closely with the experimental result. Average transmission heat loss was shown to be directly proportional to the differences between indoor and outdoor temperature, but the average overall heat transfer coefficient tended to decrease. Thus, in calculating the transmission heat loss, the overall heat transfer coefficient must be selected based on design conditions. The overall heat transfer coefficient of the experimental greenhouse averaged $2.73W{\cdot}m^{-2}{\cdot}C^{-1}$, which represents a 60% heat savings rate compared with plastic greenhouses with a single covering. The total heating load included, transmission heat loss of 84.7~95.4%, infiltration loss of 4.4~9.5%, and ground heat exchange of -0.2~+6.3%. The transmission heat loss accounted for larger proportions in groups with low differences between indoor and outdoor temperature, whereas infiltration heat loss played the larger role in groups with high temperature differences. Ground heat exchange could either heighten or lessen the heating load, depending on the difference between indoor and outdoor temperature. Therefore, the selection of a reference temperature difference is important. Since infiltration loss takes on greater importance than ground heat exchange, measures for lessening the infiltration loss are required to conserve energy.

• Journal of Nutrition and Health
• /
• v.50 no.3
• /
• pp.294-301
• /
• 2017

Purpose: The purposes of this study were to investigate food consumption practices and analyze factors that influence customer satisfaction of an HACCP applied restaurant in a highway service area. Methods: A total of 207 customer responses were used for data analysis. Statistical analyses were conducted using the SPSS program (ver. 22.0) for $x^2$-test, Pearson correlation analysis, and multiple regression analysis. Results: Reasons for visiting the highway area were using the restroom (86.0%), purchasing of meals or snacks (70.1%), taking a rest (58.5%), and shopping (3.4%) and selection attributes of food sold in the highway service area were food taste (48.8%), food safety (33.3%), and waiting time for meal (10.7%). According to the results of the survey, udon (66.2%) was the most preferred meal, followed by instant noodles (56.0%), kimbap (50.7%), pork cutlet (38.2%), and bibimbap (29.0%). In addition, coffee (73.4%) was the most preferred among snacks and beverages, followed by beverages (58.9%), walnut cake (53.1%), mineral water (52.2%), and hotbar (52.2%). Satisfaction evaluation scores of foods sold in the highway service area were highest for appropriate portion size, followed by food safety, menu variety, food taste, and reasonable price. Overall customer satisfaction scores regarding the restaurant in the highway service area was 3.24 out of 5 points on average. According to the results of the multiple regressing analysis, food taste (p < 0.001) and reasonable price (p < 0.01) had significant positive effects on overall customer satisfaction. Conclusion: To enhance customer satisfaction, restaurant managers in the highway service area should implement HACCP, improve food taste, and set up a proper price for food sold at the restaurant in the highway service area.

• Current Research on Agriculture and Life Sciences
• /
• v.2
• /
• pp.9-14
• /
• 1984

This study was performed to obtain the effective selection informations for improvement of quality and increase of yield in red pepper. The eight parents and twenty eight crosses from partial diallel were used as materials for estimation of correlations among the pericarp characters, viz, fruit length, fruit width, pericarp thickness (fresh and dry) and pericarp weight (fresh and dry), between pericarp weight and seed weight and between pericarp weight and the percent of seed weight/pericarp weight and path coefficients on fresh and dry pericarp weight. Results were as follows. In $F_1s$, fresh and dry pericarp weight had positive correlations with fruit length, fruit width, and pericarp thickness. Fresh pericarp weight was also positively correlated with dry pericarp weight. Dry pericarp thickness had a negative correlation with fruit length but had positive correlations with fruit width and fresh pericarp thickness. Fresh pericarp thickness had a positive correlation with fruit width. Significantly positive correlations between $F_1s$ and mid-parents were observed in pericarp characters. Pericarp weight had a positive correlation with seed weight but had a negative correlation with the percent of seed weight/pericarp weight. In path coefficient analysis, it was found that fruit length, fruit width and pericarp thickness had direct effects on fresh and dry pericarp weight and that fruit length had the largest direct effect in $F_1s$.

• Journal of Korean Society of Forest Science
• /
• v.90 no.1
• /
• pp.43-54
• /
• 2001

Genetic differentiation of populations is resulted from the environmental and the genetic effects, and the interactions between them. Whereas, the major factors influencing to the genetic differentiation within populations are the gene flow induced by seed or pollen dispersial, the microsite heterogeneity, and the density-dependent distribution of individuals. For the purpose of studying spatial genetic structure and the distribution pattern of Korean pines(Pinus koraiensis), we set up one $100{\times}100m$ plot at a Korean pine stand in Quercus mongolica community on Mt. Jumbong in Korea. To estimate the coefficient of spatial autocorrelation as Moran's index and an analogue, simple block distance, isozyme markers were analyzed in 325 Korean pines. For 11 polymorphic loci observed in 9 enzyme systems, the average percentage of polymorphic loci, the observed and expected heterozygocity were 72.2% 0.200, and 0.251, respectively. It was revealed the excess of homozygotes was observed in the plot, which suggests that here may be more number of consanguineous trees than expected. On the basis of isozyme genotypes observed in this study, 325 trees were classified into 147 groups in which the maximum number of trees for one group was 34. From the distance class of 24-32m, the genetic heterogeneity began to increase. The variation of simple block distance against the growth performance by tree height and diameter also showed the same trend at 24~32m class. According to high fixation index(F=0.204), the spatial genetic structure within a stand, the analysis of the growth performance, and the distribution patterns of identical genotypes, we inferred that the genetic structure of a Korean pine stand in Mt. Jumbong has been maintained rather density-dependent mechanism than the gene flow, such as the pollen dispersial or the heavy input of seeds following the forest gaps. The genetic patchy size was determined between 24~32m, which suggests that the selection of individuals for the ex situ conservation of Korean pine in Mt. Jumbong may be desirable to be made with the spatial distance over 37 meters between trees.

• Korean Journal of Soil Science and Fertilizer
• /
• v.40 no.1
• /
• pp.85-94
• /
• 2007

To determine the influence of food waste compost (FWC) application on paddy soil, FWC was applied to the paddy soil and then compared with farmer's practice as to the effects on rice and soil environment. Initially, pig manure compost (PMC) had high content of phosphorus ($15g\;kg^{-1}$) and potassium ($23g\;kg^{-1}$), while FWC had high content of total nitrogen ($13g\;kg^{-1}$) and salinity ($18.5g\;kg^{-1}$). Comparison was also made between chemical fertilizer and FWC use as a trial in the paddy field under the clay loam and sandy loam soil. In the panicle formation stage, chemical fertilizer application was proper in clay loam while PMC application was proper in sandy loam. However, chemical fertilizer produced higher yield compared to compost treatment, both on clay loam and sandy loam with 20~25% and 17~19%, respectively. The lower yield in sandy loam maybe due to slow mineralization of compost such that the crop did not effectively use it. Organic matter content in paddy soil after experiment was higher in FWC and PMC plots compared to that in chemical fertilizer plots. But the other soil properties were comparable. Therefore, the FWC compost had little effect on soil when it use as a trial in paddy field. Likewise, after the application of FWC as a trial, analysis of nitrate nitrogen and ammonium nitrogen in the surface water and 60 cm depth of paddy soil water nine days after planting was done. Results revealed that concentration of ammonium nitrogen was similar to irrigation water while nitrate nitrogen concentration was not detected, and hence did not contribute to water pollution. It is concluded that the application of FWC in the paddy field had not affected on environmental pollution in the paddy field. But its use as compost during rice culture reduced yield quantity. Such study should include selection of compost material, amount and method of compost application.

• Journal of Bio-Environment Control
• /
• v.30 no.4
• /
• pp.383-392
• /
• 2021

It has been known that oyster mushrooms cultivated in facilities with thermal insulation have been strongly affected by inner environments. Forced air-circulation fans exert much direct influence on disturbing air inside the facility so the matter is of particular interest. This study is carried out to investigate the measured levels of air uniformity in a cultivation facility for oyster mushroom in the various cases that reversibly controlled air-circulation fans which drove the flow in the upward and reverse direction by turn and unidirectional fans by which the wind blew upwards only were operated from July 1 to 10. The actual survey for the selection of ongoing operation cases presented that farmers, even though there were some discrepancies, have made use of fans in a way that it paused for 5-30min after running for 5-15min by turn. The level of air uniformity in the case of adopting reversible fans revealed a slight difference of 1.4-1.8℃ (Temp.) and 7.8-8.7% (R.H.) under the condition of not using a cooler during the investigation period. By contrast, unidirectional fans showed a noticeable difference of 3.2-3.7℃ and 14.0-15.4%, which meant that air uniformity driven by reversible fans much more increased compared to that for unidirectional fans. Among the twenty operational applications considered for reversible fans, the circumstance that the wind blew upwards for 10-15min and ceased for 5-10min and blew again in the reverse direction for 10-15min in succession gave minor improvements at the level of air uniformity, but at present there was somewhat difficult to make decision on which cases were optimally best. It seems necessary that the effects of reversible fans on air uniformity as well as qualities of oyster mushrooms have to be appraised in the cultivation period and the flow visualization needs to be done to ascertain the performance of air mixture.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.2
• /
• pp.19-30
• /
• 2019

Objective of this study was to develop an organic fertilizer utilizing domestic livestock horn meal and to investigate the application effect of rice and eggplant. The possibility of utilization of livestock horn meal as an organic resource to replace imported expeller cake fertilizer was examined. In order to select domestic organic resources with high nitrogen content, 8 kinds of organic matter such as chicken manure, fish meal, soybean meal, sesame meal, perilla meal, blood meal, livestock horn meal, and beer sludge were analyzed and organic resources with high nitrogen content were selected. In addition, the conditions for the production of organic fertilizers that can be used in organic agriculture were established by mixing of the rice husk biochar and the rice bran as the supplements with the raw materials for mixing ratios. The content of total nitrogen (T-N) in the livestock horn meal was 12.0 %, which was the next low in 13.5 % blood meal. The content of total nitrogen was 5.9 ~ 7.9 % in fish meal and oil cakes. Total nitrogen content of non-antibiotic chicken manure for organic farming was 3 % and nitrogen content in beer sludge was 3.5 %. Organic fertilizer was produced by using biochar, rice bran as a main ingredient of non-antibiotic chicken manure, livestock horn meal and beer sludge. Compared to nitrogen content (4.0 to 4.2 %) of imported expeller cake fertilizer (ECF), the nitrogen content of organic fertilizer utilizing domestic livestock horn meal is as high as 7.5 %. The developed organic fertilizer is met as Zn 400 mg/kg, Cu 120 mg/kg the quality of organic agricultural materials such as or less. To investigate the effect of fertilizer application on the crops, prototypes of developed organic fertilizer were used for the experiment under selected conditions. As a result of application the developed organic livestock horn meal fertilizer (LHMF) for cultivation of the rice and eggplant, the application quantity of the developed organic LHMF 100 % was decreased by 40 % compared to that of the mixed expeller cake fertilizer (MECF). The application of LHMF, which refers to the application rate corresponding to the nitrogen fertilization recommended by the soil test, was reduced by 40% compared to the application rate of MECF, but the same results were obtained in crop growth and yield. The selection of a new high concentration nitrogen source utilizing domestic organic resources and the development of organic fertilizer is the starting point of the research for substitution of imported ECF using domestic local resources at the present time that the spread of eco-friendly agriculture is becoming increasingly important. If it is expanded in the future, it is expected to contribute to the stable production of eco-friendly agricultural products.

• Journal of vocational education research
• /
• v.37 no.2
• /
• pp.39-75
• /
• 2018

The purpose of this study is to verify the general characteristics in the previous studies and the magnitude of the correlation between the learner's satisfaction and the academic achievement in the education and training program. To do this, we searched relevant literature from 2000 to 2016, and conducted a systematic review of the literature on the final 31 studies through the selection criteria and quality evaluation. Among them, 27 meta-analysis of the literature was conducted. The finding of the study were as follows. First, a total of 31 studies were conducted from 2000 to 2016, and more than half of them(16) were conducted for the last 4 years(2009~2012). In terms of education and training students, there are 18 college students, 9 workers, and 4 elementary students in order of study. In terms of methods, 15 collective education, 14 distance education, 2 blended education. In terms of learner's participation, 22 the general participation, 9 the active participation. Second, as a result of the meta-analysis, the magnitude of the correlation between satisfaction and achievement was moderate(ZCOR=.297, 95%: CI .210~.383). Third, as a result of verifying the difference in the magnitude of the correlation effect between satisfaction and achievement according to the characteristics of the education and training program, there was no difference between the groups in the student object and education method, but there was a difference in the magnitude of the correlation effect depending on the participant type(Q=15.40, df=1, p<.0001). The active participation showed a correlation effect size larger(ZCOR=.588, 95%: CI .422~.754). The effect size of the general participation was lower than the median(ZCOR=.211, 95%: CI .12 ~.300).

• Korean Journal of Heritage: History & Science
• /
• v.46 no.1
• /
• pp.208-227
• /
• 2013

Twenty-seven bronze bowls excavated from the Goryo burial complex at Deobu-gol were examined for their microstructure and chemical composition to characterize the bronze technology practiced by commoners at the time. Results showed that the objects examined can be classified into four groups: 1) objects forged out of Cu-near 22%Sn alloys and then quenched; 2) objects cast from Cu-below 10% Sn alloys containing lead; 3) objects cast from Cu-10%~20% Sn alloys containing lead and then quenched; 4) objects forged out of Cu-10~20% Sn alloys containing lead and then quenched. This study revealed that the fabrication technique as determined by alloy compositions plays an important role in bronze technology. The use of lead was clearly associated with the selection of quenching temperatures, the character of inclusions and the color characteristics of bronze surfaces. It was found that the objects containing lead were quenched at temperatures of $520^{\circ}{\sim}586^{\circ}C$ while those without lead were quenched at the range of $586^{\circ}{\sim}799^{\circ}C$. The presence of selenium in impurity inclusions was detected only in alloys containing lead, suggesting that the raw materials, Cu and Sn, used in making the lead-free alloys for the first group were carefully selected from those smelted using ores without lead contamination. Furthermore, the addition of lead was found to have significant effects on the color characteristics of the surface of bronze alloys when they are subjected to corrosion during interment. In leaded alloys, corrosion turns the surface light green or dark green while in unleaded alloys, corrosion turns the surface dark brown or black. It was found that in fabrication, the wall thickness of the bronze bowls varies depending on the application of quenching; most of the quenched objects have walls 1mm thick or below while those without quenching have walls 1mm thick or above. Fabrication techniques in bronze making usually reflect social environments of a community. It is likely that in the late Goryo period, experiencing lack of skilled bronze workers, the increased demand for bronze was met in two ways; by the use of chief lead instead of expensive tin and by the use of casting suitable for mass production. The above results show that the Goryo bronze workers tried to overcome such a resource-limited environment through technological innovations as apparent in the use of varying fabrication techniques for different alloys. Recently, numerous bronze objects are excavated and available for investigation. This study shows that with the use of proper analytical techniques they can serve as a valuable source of information required for the characterization of the associated technology as well as the social environment leading to the establishment of such technology.

• Journal of Nutrition and Health
• /
• v.54 no.1
• /
• pp.10-22
• /
• 2021

Purpose: Key Foods refers to foods that have a high contribution in the nutrient intake of individuals, and exert important effects on their health. This study was undertaken to identify Korean Key Foods, using data from the 7th Korea National Health and Nutrition Examination Survey (KNHNES). Methods: The data source for the extraction of Key Foods was the 24-hour dietary survey data obtained from the 7th KNHNES (2016-2018), and 21,271 subjects were evaluated. A total of 17 nutrients were selected as the key nutrients for identifying the Key Foods, including energy, carbohydrates, protein, lipid, dietary fiber, calcium, phosphorus, iron, sodium, potassium, vitamin A, thiamin, riboflavin, niacin, vitamin C, cholesterol, and sugars. The nutrient consumption approach was applied to generate a list of potential Key Foods. Foods included in 85% of the cumulative intake contribution from one or more key nutrients, were subsequently selected as Key Foods. Results: Of the 1,728 foods consumed by survey respondents, we extracted 728 Key Foods. These Key Foods explained 94% key nutrient intakes of the subjects. Based on the contribution rate to key nutrient intake, the top 10 Key Foods identified were multigrain rice (5.32%), plain white rice (4.23%), milk (3.3%), cabbage kimchi (2.82%), grilled pork belly (1.56%), apples (1.52%), fried eggs (1.49%), cereal (1.36%), instant coffee mix (1.21%), and sweet potatoes (1.12%). These 10 foods accounted for 23.93% total key nutrient intake of the survey respondents. Conclusion: Seven hundred and twenty-eight foods were extracted and identified as the 2020 Korean Key Foods. These Key Foods can be considered the priority foods to be analyzed for establishing a national nutrient database.