• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.4
• /
• pp.639-647
• /
• 2002

A simplified analytical procedure is presented to estimate the reduction of elastic lateral stiffness of steel moment frames arising from the radius-cut dogbone weakening. With the original radius-cut dogbone shape, it is almost impossible or too complicated to integrate analytically the mathematical expressions encountered when applying the conjugate beam method to compute the beam deflection component. In this study, the problem is circumvented by replacing the original radius-cut dogbone with an equivalent dogbone of constant width. The equivalence between the two is established by imposing an equal dogbone elongation criterion. This approach is justified by using a calibrated finite clement analysis. Then, the elastic lateral deflection components from the column, panel zone, and beam are derived for a typical beam-column subassembly. The derived results can be used to evaluate the reduction of the frame lateral stiffness. Case studies conducted within some practical ranges of frame configurations show that the reduction in frame lateral stiffness due to the presence of dogbone cut is on the order of 1 to 2 percent and is reasonably negligible in practical sense.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.4
• /
• pp.35-42
• /
• 2015

This study analytically reviewed the behavior of Steel Plate Concrete(SC) walls subjected to cyclic loads to investigate the effects of shape and arrangement spacing of studs on the behavior of SC walls. To perform it, 9 cases of finite element analyses considering the different shape and spacing of studs in SC wall were carried out. As the results, the skeleton curves were obtained from the load-displacement history curves and the ultimate and yielding forces were increased as the spacing of studs decrease. In addition, the strength of inclined studs are shown to be bigger compared to that of general studs. The damping ratios are increased as the decrease of strength ratio. Finally, as the decrease of stud spacings, the cumulative dissipated energy was increased and the seismic performance was improved.

• Geophysics and Geophysical Exploration
• /
• v.12 no.4
• /
• pp.281-288
• /
• 2009

Using analytical method, intrinsic absorption and scattering attenuation was lately separated from total quality factor $(Q^{-1}_t)$ on the seismic data of Korean Peninsula. However, we should use numerical method rather than the analytical method to consider depth dependent structure of scattering. The direct simulation Monte Carlo (DSMC) method, as a kind of the numerical method, is good option due to its extended availability from 1 to 3-dimensional model; but there is few study to use it. In this paper, we introduced the analytical method and the DSMC method, and compared the results of the two analysis applied to the isotropic scattering model. While the scattering attenuation coefficients $(\eta_s)$ are identical, the intrinsic absorption coefficients $(\eta_i)$ for the analytical method are larger than those for DSMC method and have large errors. In addition, the $(Q^{-1}_t)$ by the previous studies show closer to DSMC method than analytical method.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.1 no.4
• /
• pp.21-28
• /
• 1997

The aseismic capacity of a traditional three-bay-straw-roof wooden house for soft soil site condition is quantitatively estimated. One 1/4 scale model was tested for the Imperial Valley Earthquake up to failure. The natural frequency of the wooden house measured in elastic range is 1.66 Hz and 1.76 Hz in the longitudinal and transversal direction, respectively. Damping ratio of the house measured in elastic range is 7%. The peak horizontal acceleration response of the house was reduced compared with input motion due to the nonlinear inelastic characteristics of the wooden frame. The horizontal displacement response was significantly increased as the level of input motion was increased. The model was collapsed at 0.25g due to the low frequency contents of the input motion. The results of nonlinear seismic analysis were compared with the test results.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.6
• /
• pp.33-43
• /
• 2010

This paper deals with the hybrid structural test technique which has been introduced and studied currently in Korea. In this study, a Mini-MOST system which was developed as a part of NEES research was modified and improved to reduce the total simulation time to half of the original system. Using the proposed system together with the 2 dimensional small steel frame specimen, the validity and efficiency of the hybrid test technique is investigated. Even though the hybrid test has been developed as an alternative to the shaking table test and has been studied and applied for a long time in several countries, no attempt has been made to compare it directly with the shaking table test. Therefore, in this study, the hybrid test results are compared with those of the shaking table test as well as with a numerical simulation for the verification of hybrid test. From the comparison and analysis of the test results, it is concluded that the hybrid test can simulate the actual seismic behavior of structural systems very accurately and it can be a good alternative to the shaking table test.

• Journal of the Korea Concrete Institute
• /
• v.15 no.3
• /
• pp.470-481
• /
• 2003

Exterior plate-column connection has an unsymmetrical critical section for eccentric shear of which perimeter is less than that of interior connection, and hence, around the connection, unbalanced moment and eccentric shear are developed by both gravity load and lateral loads. Therefore, exterior connection is susceptible to punching shear failure. Current design provision cannot accurately explain strength of existing experiments, partly due to the complexity in the behavior of exterior plate-column connection, or partly due to the theoretical deficiency of the strength analysis model adopted. In the present study, nonlinear finite element analyses were performed for exterior connections belonging to continuous flat plate. For each direction of lateral load, the behavior and strength of exterior plate-column connection were quite different. Based on the numerical result, strength prediction model for exterior connection was proposed for each direction of lateral load. Compared with existing experiments, the proposed method was verified.

• Journal of the Korea Concrete Institute
• /
• v.22 no.2
• /
• pp.171-177
• /
• 2010

Recently, Performance Based Design (PBD) method has been studied as a next generation structural design method, which enables a designed structure to satisfy the required performance during its service life. One method of deciding whether the required performance has been satisfied is Bayesian method, which has been commonly used in seismic analysis. Generally, it is presented as a conditional probability of exceeding some limit state (i.e., collapse) for a given ground motion. In PBD of concrete mixture design, the same methodology can be applied to assess concrete material performance based on some conditional parameters (i.e. strength, workability, carbonation, etc). In this paper, a detailed explanation of the procedure of drawing satisfaction curve by using Bayesian method based on various material parameters is shown. Also, a discussion of using the developed satisfaction curves for PBD for concrete mixture design is presented.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.157-160
• /
• 2008

The confined concrete subjected multi-axil stresses have been known as the strength of concrete increases significantly. Many researchers have studied in confining effect of concrete, and now are studying in many fields. Lap splices were located in the plastic hinge region of most bridge piers that were constructed before the adoption of the seismic design provision of Korea Highway Design Specification on 1992. But sudden brittle failure of lap splices may occur under loading. This study introduces a new method to retrofit RC bridge columns with lap splice which do not have enough ductility during an earthquake. The new method use mechanical external pressure and steel plates around RC columns. The jacketing built following the new method shows good results of increasing the compressive strength and ductility of concrete cylinders. The thicker steel jacket shows larger compressive strength, however, the ductility at failure depends on the welding quality of steel jackets. In this study, The effect of the new method is verified through comparing the results of the compressive tests and analysis results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.129-132
• /
• 2008

Coupled shear wall system is the primary seismic load resisting system of buildings. The coupling beam of these buildings must exhibit excellent ductility and energy dissipation capacity. To achieve better ductility and energy dissipation, the steel coupling beam embedded in the reinforced concrete walls is proposed. Performance of the steel coupling beam is mainly effected by embedment length. ACI equation and BS equation were examined with 23 previous test results. The statistical study uses the values of mean value, standard deviation, correlation coefficient, normal distribution curve, and error analysis. Through the analytical program, the evaluation of the 2 equations was established.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.241-244
• /
• 2008

In general, RC flat plate frames have been used as a gravity load resisting system(GLRS) in building. This system should be constructed with lateral force resisting system(LFRS) such as shear walls and brace frames. When lateral loads such as earthquakes occur, LFRS undergo displacement by which connected gravity systems experience lateral displacement. Thus, flat plate system designed as GLRS should be predict unbalanced moments and punching failure due to lateral deformation. This study developed an analytical mode for predicting nonlinear behavior of RC slab column connection for the seismic performance evaluation of RC flat plate frames. For verifying the analytical model, the test results of two flat plate specimens having two continous spans with the difference gravity shear ratio($V_g/{\phi}V_c$) were compared with the results of analysis. The developed model can predict the failure modes and punching failures.