• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.85-90
• /
• 2018

For the recovering rare earths in the spent nickel-metal hydride batteries, 10 M NaOH is added to the solution leached with sulfuric acid. The rare earth powders were precipitated at rate of 98 % at the condition of pH 2.0 or less. The recovered rare earth complex precipitate increased the leaching rate to nitric acid by heat treatment at $800^{\circ}C$ for 4 hours. Subsequently secondary precipitation was performed by adding oxalic acid to the solution in which the rare earth complex precipitate was dissolved. The re-precipitated rare earth powders were converted into oxide form through heat treatment at $800^{\circ}C$ for 4 hours with purity of 99.5 %.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.7
• /
• pp.447-453
• /
• 2017

In this study, $Li_2MnSiO_4$ cathode material and LiPON solid electrolyte were manufactured into thin films, and the possibility of their use in thin-film batteries was researched. When the RTP treatment was performed after $Li_2MnSiO_4$ cathode thin-film deposition on the SUS substrate by a sputtering method, a ${\beta}-Li_2MnSiO_4$ cathode thin film was successfully manufactured. The LiPON solid electrolyte was prepared by a reactive sputtering method using a $Li_3PO_4$ target and $N_2$ gas, and a homogeneous and flat thin film was deposited on a $Li_2MnSiO_4$ cathode thin film. In order to evaluate the electrochemical properties of the $Li_2MnSiO_4$ cathode thin films, coin cells using only a liquid electrolyte were prepared and the charge/discharge test was conducted. As a result, the amorphous thin film of RTP treated at $600^{\circ}C$ showed the highest initial discharge capacity of about $60{\mu}Ah/cm^2$. In cases of coin cells using liquid/solid double electrolyte, the discharge capacities of the $Li_2MnSiO_4$ cathode thin films were comparable to those without solid LiPON electrolyte. It was revealed that $Li_2MnSiO_4$ cathode thin films with LiPON solid electrolyte were applicable in thin film batteries.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.1
• /
• pp.36-42
• /
• 2007

In general, the battery and the(electric) condenser are pictured as electrical energy storage devices. Although there were lots of inventions and utilizations of morden conveniences according to enormous growth of the science and technologies after the Industrial Revolution, a speed of technology development on these devices being closely used in civilized human lives and many electric or electronic systems as a core component are relatively slower to the other fields of technologies. Nevertheless, based on a remarkable progress of the material science and technologies for the last ten years, a new type of electrical energy storage device so called as 'electrochemical capacitors' are being developed and used practically. The electrochemical capacitors exhibit their own characteristics of much enhanced capacitance over the conventional condensers and also distinctively exhibit a longer lift time and higher power capability that the nickel hydrogen batteries and secondary batteries such as lithium ion and polymer batteries does not show up so for. Hence, in this paper, it is intended to introduce a fundamental understanding and updated technology trends on the electrochemical capacitors.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.4
• /
• pp.306-315
• /
• 2016

Amorphous vanadium titanates (aVTOs) are examined for use as a negative electrode in lithium-ion batteries. These amorphous mixed oxides are synthesized in nanosized particles (<100 nm) and flocculated to form secondary particles. The $V^{5+}$ ions in aVTO are found to occupy tetrahedral sites, whereas the $Ti^{4+}$ ions show fivefold coordination. Both are uniformly dispersed at the atomic scale in the amorphous oxide matrix, which has abundant structural defects. The first reversible capacity of an aVTO electrode ($295mAhg^{-1}$) is larger than that observed for a physically mixed electrode (1:2 $aV_2O_5$ | $aTiO_2$, $245mAhg^{-1}$). The discrepancy seems to be due to the unique four-coordinated $V^{5+}$ ions in aVTO, which either are more electron-accepting or generate more structural defects that serve as $Li^+$ storage sites. Coin-type Li/aVTO cells show a large irreversible capacity in the first cycle. When they are prepared under nitrogen (aVTO-N), the population of surface hydroxyl groups is greatly reduced. These groups irreversibly produce highly resistive inorganic compounds (LiOH and $Li_2O$), leading to increased irreversible capacity and electrode resistance. As a result, the material prepared under nitrogen shows higher Coulombic efficiency and rate capability.

• Journal of the Korean Institute of Gas
• /
• v.27 no.4
• /
• pp.50-55
• /
• 2023

Lithium-ion secondary batteries are currently in high demand and supply. The purpose of this study is to secure the safety of the process by studying the combustion characteristics of EC(Ethylene Carbonate), Which is mainly used as an electrolyte organic solvent for lithium ion batteries. The flash points of the EC by using Setaflash and Pensky-Martens closed-cup testers were experimented at 141 ℃ and 143 ℃, respectively. The flash points of the EC by Tag and Cleveland open cup testers were experimented at 152 ℃ and 156 ℃, respectively. The AIT(Auto Ignition Temperature) of the EC was experimented at 420 ℃. The LEL(Lower Explosive Limit) calculated by using lower flash point of Setaflash was calculated at 3.6 Vol.%.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.1
• /
• pp.11-18
• /
• 2023

As the use of lithium-ion secondary batteries is rapidly increasing due to the rapid growth of the electric vehicle market, the disposal and recycling of spent batteries after use has been raised as a serious problem. Since stored energy must be removed in order to recycle the spent batteries, an effective discharging process is required. In this study, graphite and NCM622 were used as active materials to manufacture coin-type half cells and full cells, and the electrochemical behavior occurring during overdischarge was analyzed. When the positive and negative electrodes are overdischarged respectively using a half-cell, a conversion reaction in which transition metal oxide is reduced to metal occurs first in the positive electrode, and a side reaction in which Cu, the current collector, is corroded following decomposition of the SEI film occurs in the negative electrode. In addition, a side reaction during overdischarge is difficult to occur because a large polarization at the initial stage is required. When the full cell is overdischarged, the cell reaches 0 V and the overdischarge ends with almost no side reaction due to this large polarization. However, if the full cell whose capacity is degraded due to the cycle is overdischarged, corrosion of the Cu current collector occurs in the negative electrode. Therefore, cycled cell requires an appropriate treatment process because its electrochemical behavior during overdischarge is different from that of a fresh cell.

• Journal of the Korean Electrochemical Society
• /
• v.21 no.1
• /
• pp.6-11
• /
• 2018

For the high performance of the secondary battery to satisfy the demands in electronic and energy industries, it is necessary to develop more safe, environmentally friendly and economical electrode. Recently, lithium-sulfur batteries are receiving attention as next-generation secondary cells in terms of its remarkable theoretical capacity, energy density and environmental characteristics. However, they have not yet overcome a fading phenomenon due to the dissolving of the polysulfide. In this study, we intend to fabricate a battery using sulfur, a higher energy density than the other bipolar materials, as an improved secondary cell electrode material. The aim of the study is to improve battery performance with an optimal ratio of the cathode components; such as sulfur of active material and Super P of an electronic conductor.

• Journal of the Korean Electrochemical Society
• /
• v.21 no.2
• /
• pp.39-46
• /
• 2018

Many studies on the electrochemical performance of Li secondary batteries have been obtained using coin-type cells due to the ease of assembly, low cost and ensuring reproducibility. The coin-type cell consists of a case, a gasket, a spacer disk, and a wave spring. These structural features require a greater amount of liquid electrolyte to assemble than other types of cells such as laminated cells and cylindrical cells. Nevertheless, little research has been conducted on the effect of excess liquid electrolytes on the electrochemical performances of Li secondary batteries. In this study, we investigate the effect of different amounts of electrolyte on the coin-type cells. The amount of electrolytes is adjusted to 30 and $100mg\;mAh^{-1}$. Cycle performances at room temperature ($25^{\circ}C$) and high temperature ($60^{\circ}C$) and high voltage are performed to investigate the electrochemical properties of the different amount of electrolytes. In the case of the unit cell including the electrolyte of $30mg\;mAh^{-1}$, the discharging capacity retention characteristic is excellent in comparison with the case of $100mg\;mAh^{-1}$ under the high temperature and high voltage condition. The former shows a larger increase in internal resistance than the latter, confirming that the amount of electrolyte significantly influences the discharge capacity retention characteristics of the battery.

• Resources Recycling
• /
• v.28 no.5
• /
• pp.3-18
• /
• 2019

Due to the increasing demand for clean energy, the consumption of lithium ion batteries (LIBs) is expected to grow steadily. Therefore, stable supply of lithium is becoming an important issue globally. Commercially, most of lithium is produced from the brine and minerals viz., spodumene, although various processes/technologies have been developed to recover lithium from other resources such as low grade ores, clays, seawaters and waste lithium ion batteries. In particular, commercialization of such recycling technologies for end-of-life LIBs being generated from various sources including mobile phones and electric vehicles(EVs), has a great potential. This review presents the commercial processes and also the emerging technologies for exploiting minerals and brines, besides that of newly developed lithium-recovery-processes for the waste LIBs. In addition, the future lithium-supply is discussed from the technical point of view. Amongst the emerging processes being developed for lithium recovery from low-grade ores, focus is mostly on the pyro-cum-hydrometallurgical based approaches, though only a few of such approaches have matured. Because of low recycling rate (<1%) of lithium globally compared to the consumption of lithium ion batteries (56% of lithium produced currently), processing of secondary resources could be foresighted as the grand opportunity. Considering the carbon economy, environment, and energy concerns, the hydrometallurgical process may potentially resolve the issue.

• Particle and aerosol research
• /
• v.15 no.4
• /
• pp.127-137
• /
• 2019

Recently, high electrochemical performance anode materials for lithium ion secondary batteries are of interest. Here, we present silicon-carbon-graphene (Si-C-GR) composites for high performance anode materials of lithium ion secondary battery (LIB). Aerosol process and heat-treatment were employed to prepare the Si-C-GR composites using a colloidal mixture of silicon, glucose, and graphene oxide precursor. The effects of the size of the silicon particles in Si-C-GR composites on the material properties including the morphology and crystal structure were investigated. Silicon particles ranged from 50 nm to 1 ㎛ in average diameter were employed while concentration of silicon, graphene oxide and glucose was fixed in the aerosol precursor. Morphology of as-fabricated Si-C-GR composites was generally the shape of a crumpled paper ball and the Si particles were well wrapped in carbon and graphene. The size range of composites was about from 2.2 to 2.9 ㎛. The composites including silicon particles larger than 200 nm in size exhibited higher performance as LIB anodes such as capacity and coulombic efficiency than silicon particles less than 100 nm, which were about 1500 mAh/g at 100 cycles in capacity and 99% in coulombic efficiency, respectively.