• Food Science and Preservation
• /
• v.23 no.3
• /
• pp.422-431
• /
• 2016

To investigate the causes of the thermal deformations of packaging materials when microwave-heating ready-to-eat sauce products packaged in stand-up pouches, patterns of temperature changes were determined using an infra-red thermal imaging camera, a thermo-sensitive tape, and a fiver-optic thermometer. The temperature distributions of spicy chicken sauce and Indian curry samples in a stand-up pouch were found to be uneven during micrewave heating. A sharp increase in the temperature was detected, especially above the filling layers and in the corners of sealing layers of the package. The temperature measurements using an infra-red thermal imaging camera are restricted to the surface, and therefore might underestimate the actual temperature. Using a thermo-sensitive tape, temperature up to $200^{\circ}C$ were measured in the spicy chicken sauce sample showing package deformation. When the temperature is measured using a fiber-optic thermometer, it is crucial to have precise sensor performance to accurately measure the temperature in a narrow hot-spot area of the package. In this experiment, the fiber-optic thermometer was attached to a GaAs crystal sensor, which obtained more sensitive and accurate temperature measurements than those by a convectional sensor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.798-806
• /
• 2020

Dental sealant is a procedure to prevent dental caries on the occlusal surface of healthy teeth. Raw data from the 6th-7th Korean National Health and Nutritional Examination Survey (KNHANES) were analyzed. This study was conducted to provide basic data which is necessary for the national health care project and for expanding the standards of coverage for the Dental sealant procedure. In this study, subjects were a total of 4,366 children from the age of 6 to 18 and surveyed for the Amount of Received Dental sealant and rate of Received Dental sealant. In 2012, the coverage rate for pit and fissure sealing procedures differed significantly in terms of age, residential area and average monthly income. This coverage varied as per average monthly income in 2014 and as per age and average monthly income in 2017 (P < 0.05). In 2014, average monthly income had a significant influence on the coverage rate, while age and average monthly income had a significant influence on it in 2017 (P < 0.05). These findings suggest that in order to increase the sealing procedure coverage, continuous promotion of dental sealant projects, reduction of copayments, inclusion of varied tooth types and age groups, expansion of coverage to isolated areas and inclusion of socially disadvantaged groups are necessary.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.3
• /
• pp.23-30
• /
• 2012

For cracked concrete, it is obvious that cracks should be preferential channel for the penetration of aggressive substances such as chloride ions according to the previous researches. In order to extend the lifetime of cracked concrete, critical issues in the performance of the concrete is the risk of chloride-induced corrosion. Even though crack width can be reduced due to the high reinforcement ratio, the question is to which extend these cracks may jeopardize the durability of cracked concrete. If the size of crack is small, surface treatment system can be considered as one of the best options to extend the service life of concrete structures exposed to marine environment simply in terms of cost effectiveness versus durability performance. Thus, it should be decided to undertake an experimental study on the effect of surface coating system, which can be able to seal the concrete and the cracks to aggressive substances-induced corrosion in particular. In this study, it is excuted to examine the effect of surfaced treated systems on chloride penetration and carbonation through compressive stress induced cracks. Experimental results have showed conclusively that critical stress linked with deterioration, should be existed in compressive stress ratio 50 ~ 70% for chloride penetration and 70 ~ 80% for carbonation, respectively. When the critical stress is exceeded in concrete, a comparatively large deterioration was measured where the critical stress in concrete, the increase in the mass transportation is marginal in spite of the large increase in micro-cracks. As for the effect of surface coating system on crack-sealing, it can be seen conclusively that cracks can be healed.

• Restorative Dentistry and Endodontics
• /
• v.33 no.1
• /
• pp.66-75
• /
• 2008

This study examined the influence of the apical sizes on the sealing ability of a root canal filling. Thirty-six single rooted teeth with a single canal were divided into 3 groups (n = 12) and instrumented with either the $Profile^{(R)}$ or $LightSpeed^{(R)}$ system to achieve three different apical sizes (master apical file [MAF] of #25, #40, or #60). The teeth were filled with gutta perch a using a modified continuous wave technique. The level of microleakage was determined by immersing ten teeth from each group into India ink for 1 week followed by clearing with nitric acid, ethyl-alcohol, and methylsalicylate. The microleakage was measured using vernier calipers. The data was analyzed statistically using Kruskal-Wallis one-way ANOVA and a Student-Newman-Keuls Method. Two teeth from each group were sectioned horizontally at 1, 2, 3 and 4 mm from the apex in order to observe a cross section. The apical size was significantly (p < .05) influenced the level of microleakage. In the Student-Newman-Deuls Method, MAF sizes of #25 and #40; and MAF sizes of #25 and #60, respectively showed a statistically significant difference. There was no significant difference between #40 and #60. In most cross sections, oval-shaped canals were observed, and the irregularity of the internal surface increased with decreasing apical size. There was also an increase in the area of recess, which is the area where the canal space is not filled with either gutta-percha or sealer. When the root canals are filled using a modified continuous wave technique, canal filling with more consistent and predictable outcome may be expected as the apical preparation size is increased.

• Restorative Dentistry and Endodontics
• /
• v.30 no.5
• /
• pp.355-362
• /
• 2005

The purpose of this study was to compare the effect on marginal leakage of a resin surface sealant (Biscover) applied before or after polymerization of composite resin to unsealed composite restorations. Thirty Class V cavities with the occlusal margin in enamel and cervical margin in dentin or cementum were prepared on the buccal surfaces of sound extracted molars and restored with a microfilled light-cured composite resin (Micronew). Restorations were randomly assigned into one of three equal groups (n = 10): a control group - no surface sealing, group 1 - applied Biscover after polymerization of the composite resin. and group 2 - applied Biscover before polymerization of the composite resin. Specimens were thermocycled, immersed in a $20\%$ methylene blue solution for 4 hoots, sectioned longitudinally, and analyzed for leakage at the occlusal and gingival margins. The results of this study were as follows 1. In sealed group, group 2 showed higher microleakage than group 1 at both occlusal and gingival margins. but there was no significant difference between two groups (p > 0.05). 2. Unsealed control group showed a little higher microleakage than sealed group at occlusal margins, and a little Higher or similar microleakage than sealed group at gingival margins (p > 0.05) 3. Control group and group 2 showed significantly less microleakage at the occlusal margins, but group 1 showed no significantly difference between microleakage at the occlusal and gingival margins.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.3
• /
• pp.124-127
• /
• 2005

It is demonstrated that the annealing process for Ti in-diffusion to z-cut $LiNbO_3$ at temperature lower than the curie temperature in a platinum (Pt) box can cause a ferroelectric micro-domain inversion at the +z surface and Li out-diffusion, therefore which should be avoided or suppressed for waveguide type periodically poled lithium niobate (PPLN) devices. The depth of the inversion layer depends on the Ti-diffusion conditions such as temperature, atmosphere, the sealing method of $LiNbO_3$ in the Pt box and crystal orientation is experimentally examined. The result shows that the polarization-inverted domain boundary appears at the only +z surface and its thickness is about $1.6{\mu}m$. Also, for the etched $LiNbO_3$, surface the domain shape was observed by the optical microscope and atomic force microscopy (AEM), and distribution of the cation concentrations in the $LiNbO_3$ crystal by the secondary ion mass spectrometry (SIMS).

• Restorative Dentistry and Endodontics
• /
• v.31 no.4
• /
• pp.282-289
• /
• 2006

The purpose of this study was to compare the ability of three resin surface sealants to prevent microleakage in Class V composite resin restorations. Forty Class V cavities with the occlusal margin in enamel and gingival margin in dentin were prepared on the buccal surfaces of sound extracted molars, and restored with composite resin. Restorations were randomly assigned into one of four equal groups (n = 10): a control group, without resin sealing, and three experimental groups in which margins were sealed with Fortify Plus, Biscover and Permaseal, respectively. Specimens were thermocycled, immersed in a 2% methylene blue solution for 4 hours, sectioned longitudinally, and observed the leakage at the occlusal and gingival margins. The result was analyzed using Kruskal-Wallis test, Mann-Whitney test and Wilcoxon signed rank test. In conclusion, the ability to reduce microleakage at occlusal margins was similar in all of three sealants. However at gingival margin, it depended on the type of used resin surface sealant. At gingival margin. control and Fortify Plus group showed statistically higher microleakage than PermaSeal group. and Fortify Plus group also showed higher microleakage than BisCover group (p < 0.05).

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.4
• /
• pp.338-345
• /
• 2014

Fabrication of complete denture by Jiro Abe's method was introduced that enhance the retention and stability of denture by sealing around the denture border with mucous membrane to make negative pressure at the inner surface of denture base when swallowing or occlusion. In this case, taking impression and fabricating complete denture by the Jiro Abe's method for an edentulous patient with severe mandibular alveolar bone resorption allowed us to obtain clinically enhance stability of denture and improve satisfaction of patient.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.6
• /
• pp.583-591
• /
• 2012

This study selected three model designs used for air injection type welding clothes designed for insulation purposes and analyzed the performance of each design. The bending characteristics were analyzed in order to identify the flexibility of the welded areas; subsequently, the seam breaking strength and water pressure resistance were analyzed to identify the bonding strength. In addition, two types of waterproof fabric, polyurethane (PU) coated 2 layer and PU laminated 2 layer fabrics, were used for a performance analysis, according to fabric processing specifications. The circle type showed the highest flexibility in the terms of bending characteristics that influence wearability and were followed by the wave and the straight type. In terms of breaking strength, the straight type showed the highest breaking strength, followed by the wave and the circle type. The water pressure resistance analysis found that the wave type was superior to the straight type in terms of water pressure resistance. The wave type is deemed to be a design type suitable for maximizing performance, provided that the issue of stabilization in the welding production process is addressed. Looking at the bending characteristics of waterproof fabric for each specification, the laminating waterproof cloth outperformed the coated waterproof cloth in terms of flexibility. However, in terms of seam breaking strength, the coated waterproof cloth outperformed the laminated cloth. In contrast, the water pressure resistance of the laminated waterproof fabric was found to be higher than the coated waterproof fabric, leading to the conclusion that the bonding strength of the laminated waterproof fabric is higher than that of the coated waterproof fabric based on the assumption of injecting air.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.7
• /
• pp.687-692
• /
• 2015

A mold design for in-mold coating was developed to achieve simultaneous coating and injection molding of an automotive armrest. The developed mold includes one core and two cavities which are composed of a substrate cavity and a coating cavity. The core was attached to a movable plate and two cavities were mounted on a plate sliding in a stationary plate. In a two-step process, the part was first injection molded and subsequently, with the aid of a sliding table, was transferred to a second cavity. The materials used were PC/ABS for substrate and two-component polyurethane for coating. The experiments were conducted by changing the flow rate to investigate mixing characteristics. As the flow rate increased, the mixing improved. Additionally, the bubbles appeared over the substrate surface decreased with an increase of the weight of injected coating material.