• Journal of Information Display
• /
• 제4권3호
• /
• pp.6-11
• /
• 2003

We have fabricated a carbon nanotube field emission display (CNT-FED) panel with a 2-inch diagonal size by using a screen printing method and vacuum in-line sealing technology. The sealing temperature of the panel was around 390$^{\circ}C$ and the vacuum level was obtained with 1.4x$10^{-5}$torr at the sealing. When the field emission properties of a fabricated and sealed CNT-FED panel were characterized and compared with those of the unsealed panel which was located in a test chamber of vacuum level similar with the sealed panel. As a result, the sealed panel showed similar I-V characteristics with unsealed one and uniform light emission with very high brightness at a current density of 243 ${\mu}A/cm^2$, obtained at the electric field of 10 V/${\mu}m$.

• Transactions on Electrical and Electronic Materials
• /
• 제7권3호
• /
• pp.129-133
• /
• 2006

Ferroelectric PZT heterolayered thick films were fabricated by the alkoxide-based sol-gel method. PZT(20/80) and PZT(80/20) paste were made and alternately screen-printed on the alumina substrates. The coating and drying procedure was repeated 4 times to form the heterolayered thick films. The thickness of the PZT heterolayered thick films was approximately $60{\mu}m$. All PZT thick films showed the typical XRD patterns of a polycrystalline rhombohedral structure. And in the PZT thick films sintered at $1100^{\circ}C$, the pyrochlore phase was observed due to the evaporation of PbO. The relative dielectric constant and the dielectric loss of the PZT thick films sintered at $1050^{\circ}C$ were 445.2 and 1.90 % at 1 kHz, respectively. The remanent polarization and coercive field of the PZT thick films sintered at $1050^{\circ}C$ were $14.15{\mu}C/cm^2$ and 19.13 kV/cm, respectively.

• Transactions on Electrical and Electronic Materials
• /
• 제12권1호
• /
• pp.11-15
• /
• 2011

In this study, $ZnGa_2O_4$ phosphors in its application to field emission displays and electroluminescence were synthesized through the precipitation method and $Mn^{2+}$ ions. A green luminescence activator, $Cr^{3+}$ ions, and a red luminescence activator were separately doped into $ZnGa_2O_4$, which was then screen printed to an indium tin oxide substrate. The thick films of the $ZnGa_2O_4$ were deposited with the various thicknesses using nano-sized powder. The best luminescence characteristics were shown at a thickness of 60 ${\mu}m$. Additionally, green-emission $ZnGa_2O_4:Mn^{2+}$ and red-emission $ZnGa_2O_4:Cr^{3+}$ phosphor thick films, which have superior characteristics, were manufactured through the screen-printing method. These results indicate that $ZnGa_2O_4$ phosphors prepared through the precipitation method have wide application as phosphor of the full color emission.

• 대한의용생체공학회:의공학회지
• /
• 제43권4호
• /
• pp.219-229
• /
• 2022

In this study, we propose a miniaturized micro-ceramic heater device. After screen-printing a silver paste between pre-sintered two aluminum oxide plates to integrate a heating circuit, the device was fabricated through a low-temperature sintering process. In order to configure the optimal heating circuit integration condition, the output current evaluation and heating test were performed according to the number of screen prints of the silver paste at various voltages. A silver paste-based heating circuit printed with a line width of 200 ㎛ and a thickness of 60 ㎛ was successfully integrated on a pre-sintered alumina substrate through a low-temperature sintering process. In the case of the 5 times printed device, the thermal response showed a response rate of 18.19 ℃/sec. To demonstrate feasibility of the proposed device in the medical field, such as bio-tissue suturing and hemostasis, a voltage was applied to pig tissue in the device to test tissue change due to heat generated from the device. These results show the possibility that the proposed small ceramic heater could be used in the medical field based on its excellent temperature response.

• 한국인쇄학회지
• /
• 제26권1호
• /
• pp.73-85
• /
• 2008

We have manufactured a photoresist which has excellent dispersity and good applying property due to 330cps of viscosity for environment-friendly and economical maskless screen plate making. And the photoresist applied on the screen stretched was exposed without mask by beam projector with CRT light source. Then it was developed by air spray with $1.7kgf/cm^2$ of injection pressure. The pencil hardness and solvent resistance of curing photoresist film were worse than those of conventional photoresist film and the maximum resolution of line image formed by maskless screen plate making was 0.5 mm since the exposure system for maskless plate making has weak light intensity and the diffusion of light. But we could obtain maskless screen plate which has sharp edges of line image and confirm a possibility of dry development process by air spray method.

• 한국인쇄학회지
• /
• 제19권2호
• /
• pp.49-57
• /
• 2001

This thesis attempts to study ink transition for on the polycarbonate multicalculator plate for automobile. For this study, the change of weight by screen printed ink transition on polycarbonate material by ink viscosity(be diluted ; 0%, 5%, 10%, 20%) was observed. The weight by screen printed ink is depended on amount of added solvent. We have studied change of the weight by the transition of the ink that was screen-printed on polycarbonate which is to be printed according to the viscosity of the ink (diluent: undiluted solution 5%, 10%, 15%, 20%). This shows that ink transition become activated since the amount of ink(or/and the viscosity of ink) is increased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1990년도 추계학술대회 논문집
• /
• pp.26-30
• /
• 1990

Bi$\_$0.7/Pb$\_$0.3/Sr$_1$Ca$_1$Cu$\_$1.8/Ox thick films were screen printed on magnesia(MgO), silver and yttrium stabilized zirconia (YSZ) substrates and were sintered in a boat with cover to prevent the evaporation. The high-Tc phase increase and the low-Tc phase and Ca$_2$PbO$_4$ decrease with an increase in sintering temperature from 835$^{\circ}C$ to 860$^{\circ}C$. YSZ substrate interact strongly with the oxide resulting in poor superconductor, while the Ag and MgO substrates were satisfactory to make screen printed superconductors. The Bi$\_$0.7/Pb$\_$0.3/Sr$_1$Ca$_1$Cu$\_$1.8/Ox thick films screen printed both on Ag and MgO substrates show high Tc phase of ~85% and Tc of 96K.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 1998년도 제1회 총회 및 추계학술발표회
• /
• pp.26-26
• /
• 1998

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.941-942
• /
• 2013

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2004년도 추계총회 및 연구발표회 초록집
• /
• pp.99.2-99.2
• /
• 2004