• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.57-62
• /
• 2013

Aerodynamic characteristics of cross section shape is an important parameter for the wind response and structural stability of long span bridges. Numerical simulation methods have been introduced to estimate the aerodynamic characteristics for more detailed flow analysis and cost saving in place of existing wind tunnel experiment. In this study, the computational fluid dynamics(CFD) simulation and large eddy simulation( LES) technique were used to estimate lift, drag and moment coefficients of four cross sections. The Strouhal numbers were also determined by the fast Fourier transform of time series of the lift coefficient. The values from simulations and references were in a good agreement with average difference of 16.7% in coefficients and 8.5% in the Strouhal numbers. The success of the simulations is expected to attribute to the practical use of numerical estimation in construction engineering and wind load analysis.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.10
• /
• pp.114-122
• /
• 2010

Today, effort to reduce greenhouse gas emissions is to be strengthened worldwide. And environment-friendly vehicle is being magnified because of energy saving and minimization of environmental pollution. In the future, the construction of EV charging facilities will be needed for Prevalence of EV in the Public Housing. So in this paper, we survey and analyze data of power usage and owned vehicles on the existing public housing according to season, day and time. And, we reviewed appropriate configuration ratio according to three kind of case. Besides, we calculate Prevalence Estimates of EV and utilization factor based on analysis result. And finally, we try to study for case model.

• Korean Journal of Construction Engineering and Management
• /
• v.12 no.3
• /
• pp.91-100
• /
• 2011

Green technologies of buildings are spreading for saving resource and energy consumption during life cycle of buildings. However, selection of optimized the technologies for applying projects is needed a lot of time and costs. Therefore prioritization is necessary to apply the technologies for buildings. An evaluation of economic value for the technologies is significant for prioritization of the technologies, however, the current evaluation system of economic value for technologies is not reflected the accurate features of the technologies. Green technologies have the objectives for reducing the emission of CO2 and saving the cost during the whole lifecycle of buildings. Thus the evaluation of economic feasibility for green technologies is needed to include the economic value from improving the environment. This paper developed the economic evaluation method integrated with LCC and LCA to accurately analyze the economic value for green technologies. Moreover, this paper drew the priority of the technologies by conducting case studies with the integrated method and analyzing the results with AHP. The conclusion of case studies, Green technologies is worth more if to include the economic value from improving the environment. Then in analysis of priority, Green intelligent component technologies were rated the highest. The conclusion of the study is able to utilize the supporting tool for making decision to select the optimized technologies for the projects and precedence study for developing future research of prioritization for green technologies. The future study for improving the developed method will supplement the various evaluation factors and apply the detailed weight to analyze the priority of green technologies.

• Korean Journal of Construction Engineering and Management
• /
• v.20 no.3
• /
• pp.22-30
• /
• 2019

The purpose of this study is to derive basic data of the Guaranteed Maximum Price(GMP) process and to present specimens that can be used at the time of execution of CM at Risk project in South Korea. CM at Risk project is issued in South Korea, but the actual data is lack. On the other hand, CM at Risk project is universalized and the market of the CM at Risk is steadily growing. Because of that, in this study, The United States cases was selected as a sample. GMP consists of CM's fee, CM contingency, project direct cost, project indirect cost, allowance. GMP negotiations are performed before the end of design completion, and after 3 rounds of estimation comparison, preliminary GMP is confirmed. GMP can be multiple contract and it is useful for Procurement of long lead materials and early construction. If the actual cost is lower than expected GMP, sharing of the saving is an option since the conflict of interests between the client and the contractor can occur.

• 한국HCI학회:학술대회논문집
• /
• 2008.02a
• /
• pp.766-771
• /
• 2008

In this paper, we propose a system of mimicking image classification for building database system. It better manages the format which recording the same advertisements multimedia in advertisements image. Recently, the work of converting database is made directly by the people. This work doses the media scanning, image editing and saving, and saving of advertising information (date, the media, the page and size, so far). Therefore, it is wasted a lot of time and manpower as inefficient business. To solve these problems, first of all we gain an image by digital camera, extract and classify candidate area of advertisements. Accordingly, our system saves database to comparison of the mimicking of all advertising and classify whether area of image is the new or existing advertising.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.751-756
• /
• 2009

In the perspective of saving energy in buildings, the high performance of insulation and air tightness for improving the heating and the cooling efficiency, has brought economically positive effects. However, these building energy saving technologies cause the lack of ventilation, which is the direct cause of increasing the indoor contaminants, and is also very harmful to the residents, because they spend over 90% of their time indoors. Therefore, the ventilation is important to keep the indoor environment clean and it can also save the energy consumption. In this study, a HEPA type nano ceramic filter is designed as a passive ventilation system to collect airborne particles and to supply fresh outdoor air. The double layer filter, which has $30{\mu}m$ in diameter at the conditions of 10wt% of concentration and 3kV/cm of the electric intensity, is produced by electrospinning. The filtration coating technology is confirmed in the solution with $SiO_2$ nano particles using polymer nano fibers. Also double layer filters are coated with $SiO_2$ nano particles and finally the porous construction materials are made by sintering in the electric furnace at $200{\sim}1400^{\circ}C$. The efficiency is measured 96.67% at the particle size of $0.31{\mu}m$, which is slightly lower than HEPA filter. However the efficiency is turned out to be sufficient.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.288-298
• /
• 2017

The system of high-speed and conventional railway vehicles is diversified, and significant technological development in performance has been achieved. This study analyzed the modal change characteristics; furthermore, it estimated the value of travel time by improving the travel time and cost for the passenger's perception of railway. In this study, we formulate a mode choice model for passengers and compare it with the mixed logit model which reflects individual taste variation. In addition, the validity of the analysis is presented through an estimation the value of travel time using the derived model. For this purpose, a stated preference survey was conducted with 510 people using public transportation. The benefits of time-saving can be accurately determined by estimating the value of time spent on the railway. Appropriate fares for public transportation can also be estimated.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.1
• /
• pp.453-458
• /
• 2024

Due to global issues such as climate crisis and rising energy costs, there is an increasing focus on energy conservation and management. In the case of South Korea, approximately 53.5% of the total energy consumption comes from industrial complexes. In order to address this, we aimed to improve issues through the 'Shared Network Utility Plant' among companies using similar energy utilities to find energy-saving points. For effective energy conservation, various techniques are utilized, and stable data supply is crucial for the reliable operation of factories. Many anomaly detection and alert systems for checking the stability of data supply were dependent on Energy Management Systems (EMS), which had limitations. The construction of an EMS involves large-scale systems, making it difficult to implement in small factories with spatial and energy constraints. In this paper, we aim to overcome these challenges by constructing a data collection system and anomaly detection alert system on embedded devices that consume minimal space and power. We explore the possibilities of utilizing anomaly detection alert systems in typical institutions for data collection and study the construction process.

• Advances in concrete construction
• /
• v.8 no.4
• /
• pp.269-276
• /
• 2019

The cracking and spalling caused by fracture of concrete lining have adverse impacts on serviceability and durability of the tunnel, and the subsequent maintenance work for damaged structure needs to be specific to the damaging causes. In this paper, a particular case study of an operational tunnel structure is presented for the serious cracking and spalling behaviours of concrete lining, focusing on the multi-factors inducing lining failure. An integrated field investigation is implemented to characterize the spatial distribution of damages and detailed site situations. According to results of nondestructive inspection, insufficient lining thickness and cavity behind lining are the coupled-inducement of lining failure bahaviors. To further understanding of the lining structure performance influenced by these multiple construction deficiencies, a reliable numerical simulation based on extended finite element method (XFEM) is performed by using the finite element software. The numerical model with 112 m longitudinal calculation, 100 m vertical calculation and 43 m vertical depth, and the concrete lining with 1450 solid elements are set enrichment shape function for the aim of simulating cracking behavior. The numerical simulation responses are essentially in accordance with the actual lining damaging forms, especially including a complete evolutionary process of lining spalling. This work demonstrates that the serious lining damaging behaviors are directly caused by a combination of insufficient thickness lining and cavity around the surrounding rocks. Ultimately, specific maintenance work is design based on the construction deficiencies, and that is confirmed as an efficient, time-saving and safe maintenance method in the operational railway tunnel.

• Journal of Welding and Joining
• /
• v.26 no.5
• /
• pp.29-35
• /
• 2008

In this paper concentrate on the comparison of the thermal and mechanical characteristics in Butt joint of ship structure AH32 steel by using hybrid welding and conventional SAW. For this purpose, fundamental welding phenomena of hybrid process using $CO_2$ Laser and MIG is investigated by the experiments and characteristics of thermal and welding residual stress distribution of welded joint in SAW and hybrid welding are understood from the result of FE numerical simulation and experimental values. From the result of this study, it is understood that Laser-MIG hybrid welding have high potential, make substantial saving of time and manufacturing cost and may proves its self robust in the butt joining of thick AH32 steel ship structural plate in the near future.