• Journal of Microbiology and Biotechnology
• /
• v.16 no.3
• /
• pp.414-422
• /
• 2006

Before applying PVA bio-beads to practical biological treatment of nitrate-containing wastewater, their characteristics were examined. PVA bio-beads could steadily produce nitrogen gas from nitrate for 28 batches with 0.04 ml/l/h of the maximum gas production rate; however, the maximum gas production rate dropped remarkably thereafter with apparent deformation of beads. Addition of 2.2% solution containing 1% casamino acid, 1% yeast extract, 0.1% mineral solution, and 0.1% vitamin solution to the culture medium resulted in not only recovery of activity of deactivated beads, but also a higher rate of gas production. Calculation of economic benefit for the use of bio-beads in a long-run operation indicated that reactivation of bio-beads by chemicals had economical advantages over packing new bio-beads in the system. The continuously stirred bioreactor exhibited a satisfactory performance at HRT of 20.0 h. With a 9.5 mg $NO_{3}^{-}N/l/h$ nitrate removal rate, nitrate could completely be removed without nitrite accumulation. The use of PVA bio-beads in nitrate removal appears very promising.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.1
• /
• pp.23-29
• /
• 2003

The effect of ozone oxidation on bio-degradability of leachate was studied. Ozone oxidation process was used as pre-treatment process to enhance performance of biological process in treating landfill leachate. Optimum ozone injection rate and contact time in this experiment was $160{\;}mg{\;}O_/{\ell}{\cdot}hr$ and 45 minutes, respectively. Bio-degradability was enhanced 5.08% by ozone oxidation. The ratio of ozone demand/DOC concentration was $0.049~0.091{\;}mg{\;}O_3/mg{\;}DOC$. The increase of bio-degradability depending on ozone injection rate(D) and contact time(T) can be expressed as follows ; The rate of bio-degradation of DOC was increased proportionally with the increase of ozone injection rate and contact time irrespective of landfill site age. The increase of bio-degradability by ozone addition was not satisfactory. It is hard to expect significant increase in bio-degradability by ozone treatment only. Thus, it is evaluated that ozone oxidation can not increase biodegradability significantly in concentrated wastewater composed of complex organic compound such as leachate.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.35 no.5
• /
• pp.361-366
• /
• 2009

Purpose: The purpose of this retrospective report was to analyze long-term survival rate of sintered porous-surfaced dental implant ($Endopore^{(R)}$ Dental Implant system, Innova Corporation, Toronto, ON, Canada). Methods: 61 partially edentulous patients were received a total of 127 Endopore dental implants in the maxilla. Of the 127 implants, 24 implants were restored with individual (ie, non-splinted) crowns, while 103 implants were splinted to other implants. Medical records and radiographs were evaluated and analyzed by the cumulative survival rate, location of implants, implants length and diameter, crown/implant ratio and whether the implant was splinted. Chi squire test was used statistically. Result: Of the 127 implants, 8 implants (6.3%) were removed and and cumulative survival rate was 93.7%. Conclusion: Endopore implants showed satisfactory results after up to 8 years function periods in the edentulous posterior maxilla.

• Journal of Korean Society on Water Environment
• /
• v.21 no.1
• /
• pp.1-6
• /
• 2005

The effect of ozone oxidation on biodegradability of leachate was studied. Ozone oxidation process was used as pre-treatment process to enhance performance of biological process in treating landfill leachate. Optimum ozone dosing rate and contact time in this experiment was $160mg\;O_3/L$ hr and 45 minutes, respectively. Biodegradability was enhanced 5.08% by ozone oxidation. The ratio of ozone demand/DOC concentration was $0.049{\sim}0.091mg\;O_3/mg$ DOC. The increase of biodegradability depending on ozone dosing rate(D) and contact time(T) can be expressed as follows ; ${\Delta}E=0.00479{\cdot}D^{0.773}{\cdot}T^{0.800}$ The biodegradation rate of DOC was increased proportionally with the increase of ozone dosing rate and contact time irrespective of landfill site age. The increase of biodegradability by ozone addition was not satisfactory. It is hard to expect significant increase in biodegradability by ozone treatment only. Thus, it is evaluated that ozone oxidation can not increase biodegradability significantly in concentrated wastewater composed of complex organic compound such as leachate.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.22 no.4
• /
• pp.96-107
• /
• 1980

This study is carried out to estimate the rate of sediment transportation both to measure the amount of suspended and bedload sediment that moves on or near the river bed and passes through the cross section of a river in unit time, with suspended and bed load samplers used for the Milyang river and to determine the most satisfactory and convenient formula of some formulas for sediment discharge by comparing the measured rate with the calculated rate. The results of this study are summarized as follows; 1) The interrelationship (1) between the total discharge and the total sediment discharge (2) between discharge and suspended sediment load and (3) between discharge and bed load in the Milyang river are (1) i) 4$\leq$Q$\leq$100 C.M.S. Qr=0. 00272 Q0.70 (kg/sec) ii) 150$\leq$Q$\leq$800 C.M.S. Qr=0. 4807 Q0.46 (kg/sec) (2) Qs~=0. 07576 Q1.02 (kg/sec) (3) QB=0. 00957 Q0.44 (kg/sec) 2) The rate of suspended sediment load to total sediment discharge is found to be about; 99%. The suspended load is shown to be almost wash load which consists of silt and clay. 3) The relation between the total discharge and the suspended sediment load that are measured at three medium and small rivers in Korea is Qs=0. 13831 Q0.97 (kg/sec) 4) Brown's formula is determined to be the most convenient formula for application and comparison with observed data obtained for the Milyang river.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.22 no.3
• /
• pp.242-248
• /
• 2019

Purpose: Severe acute malnutrition (SAM) is an important public health problem which contributes to significant number of under five deaths. Protocol based management significantly decreases risk of deaths in children with medical complications. Methods: Outcome of children aged 2 months-5 years admitted and fulfilling definition of SAM having diarrhea (group A) was compared to children with SAM having medical complications other than diarrhea (group B). Both groups were managed according to standard recommended protocols and monitored and followed up for 12 weeks after discharge. Results: The average weight gain, defaulter rate, primary failure, secondary relapse rate and readmission rate were similar in both groups. Length of stay in group A was three days longer (p-value=0.039). Discharge rate was comparable with overall 68% of children successfully discharged and 50% of children reaching weight/height > -2 standard deviation at follow-up of 12 weeks. Conclusion: The current management protocol is equally effective for managing children with SAM having diarrhea. Good adherence to management protocol of dehydration and timely modification of therapeutic feeds in children with persistent diarrhea results in satisfactory weight gain.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1201-1206
• /
• 2003

A measurement device for gas flow rate using hot-wire module is developed for the utilization in low-accuracy industrial applications. The module has three wires of measuring and heating, and a bridge circuit is installed to detect electric current through the wire in the module. An amplification of the signal and conversion to digital output are conducted for the online measurement with a personal computer. In addition, temperature distribution in the module is numerically analyzed to examine the measured outcome from the module experiment. The flow rate of air and carbon dioxide gas is separately measured for the performance examination of the device. The experimental relation of measurement and flow agrees with the prediction from the numerical analysis. The outcome of the performance test indicates that the accuracy and reproducibility of the module is satisfactory for the purpose of industrial applications.

• Journal of Drive and Control
• /
• v.13 no.4
• /
• pp.7-13
• /
• 2016

This paper presents the meter-out and meter-in speed control characteristics of a pneumatic cylinder with relief valve type cushion device. The piston displacement and velocity are measured to investigate high speed driving performance with variation of the pressure setting in relief valve, air supply pressure, load mass, the supply and exhaust flow rate from the cylinder. Also, the internal pressures and temperatures driving pressure and cushion chamber are measured. The piston displacements and velocities of meter-out and meter-in control are compared experimentally determined data. A comparison experimental data meter-out and meter-in control show that a relief valve type cushion device is suitable for high speed pneumatic cylinders. The desired response characteristics of piston displacement and velocity are satisfactory adjust the pressure setting of a relief valve with varying system parameters such as air supply pressure, load mass and controlled flow rate.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.195-199
• /
• 2001

The flow turning process, an incremental forming process, is a cost-effective forming method for axi-symmetric intricate parts to net shape. However, the flow turning process shows a fairly complicated deformation, it is very difficult to obtain satisfactory results. Therefore extensive experimental and analytical research has not been carried out. In this study, an fundamental experiment was conducted to improve productivity with process parameters such as tool path, angle of roller holder($\alpha$), feed rate(v ) and comer radius of forming roller(Rr). These factors were selected as variables in the experiment because they were most likely expected to have an effect on spring back. The clearance was controlled in order to achieve the precision product which is comparable to deep drawing one. And also thickness and diameter distributions of a multistage cup obtained by flow turning process were observed and compared with those of a commercial product produced by conventional deep drawing.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.11 no.3
• /
• pp.45-51
• /
• 2015

In this paper, we discuss the belief propagation decoding algorithm for polar codes. The performance of Polar codes for shorter lengths is not satisfactory. Motivated by this, we propose a novel technique to improve its performance at short lengths. We showed that the probability of messages passed along the factor graph of polar codes, can be increased by multiplying the current message of nodes with their previous message. This is like a feedback path in which the present signal is updated by multiplying with its previous signal. Thus the experimental results show that performance of belief propagation polar decoder can be improved using this proposed technique. Simulation results in binary-input additive white Gaussian noise channel (BI-AWGNC) show that the proposed belief propagation polar decoder can provide significant gain of 2 dB over the original belief propagation polar decoder with code rate 0.5 and code length 128 at the bit error rate (BER) of $10^{-4}$.