• Journal of environmental and Sanitary engineering
• /
• v.22 no.4
• /
• pp.1-9
• /
• 2007

A wastewater treatment plant, operating process is physico-chemical/biological activated sludge attached sand filtration, was selected to evaluate effluent quality and pollutants removal efficiencies consideration for deriving the technology-based effluent limitation for petroleum refining industry discharge. The results of influent and effluent analysis were as follows: Average effluent quality were 0.076mg/l of copper, 0.084mg/l of lead, 0.036mg/l of zinc, 0.005mg/l of nickel and 0.004mg/l of cadmium, and the range of coefficient of reliability from 0.007 of copper to 1.0 of lead. Also, 95% of reliability, 0.112, 0.15, 0.063, 0.015 and 0.009mg/l, respectively, were remarkably lower than their effluent limitations. And to reach 95% reliability of effluent limitation at cleanness area, designed effluent quality of copper, lead, zinc and cadmium should be 0.268, 0.099, 0.526 and 0.008mg/l, respectively.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.5
• /
• pp.565-571
• /
• 2005

The method to decide media sphericity on the filter has been investigated. The sphericity, the ratio of the surface area of an equal volume sphere to the real surface area of the particles, is one of major physical characters of media affecting the bed expansion during backwash. The media in each treatment plant may have different sphericity, and the sphericity of the media in the filter may be changed as backwashing has been conducted regularly for a long time. Media from twelve water treatment plants under KOWACO have been collected and selected to insure various and practical sphericities. The sphericity of each media has been calculated by using well known equations. For example, Kozeny equation, Dahmarajah equation and so on. The experiment results have indicated that the sphericity of each water treatment plant is different. Although the sphericity values measured by different methods were turned out to be diverse values, the order in the magnitude seemed to be the same. The sphericity values of sand media were in the range of 0.71-0.82 and those of anthracite were placed between 0.49 and 0.56 by the Dharmarajah equation.

• Economic and Environmental Geology
• /
• v.41 no.5
• /
• pp.587-595
• /
• 2008

The geology of the Capim region in Brazil is composed of Ipixua Formation in Mesozoic-Tertiary(Miocene), sedimentary rocks in Miocene, Barreiras Formation(sedimentary rocks) in Pleistocene and sediments in Holocene. Kaolin deposit consists of Barreiras Formation(average depth in 120m) composed of sandstone, clay, fine sand of Miocene to Pliocene age. Kaolin of the high grade is white in color and its thickness averages 7m. The orebody formed by kaolinite was confirmed by XRD, is shape of hexagonal, SK is above 33 degree. It is class A also suit for producing a paper without filtration. According to the CPRM report, the reservation of kaolin ore is amounts of 566,819,164 tons.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.5
• /
• pp.357-371
• /
• 2020

Microplastics have become a rising issue in due to its detection in oceans, rivers, and tap water. Although a large number of studies have been conducted on the detection and quantification in various water bodies, the number of research conducted on the removal and treatment of microplastics are still comparatively low. In the current research, the inflow and removal of microplastics were investigated for various drinking water treatment plants around the world. Addition to the investigation of filed research, a survey was also conducted on the current research trend on microplastic removal for different treatment processes in the drinking water treatment plants. This includes the researches conducted on coagulation/flocculation, sedimentation, dissolved air flotation, sand filtration and disinfection processes. The survey indicated mechanisms of microplastic removal in each process followed by the removal characteristics under various conditions. Limitations of current researches were also mentioned, regarding the gap between the laboratory experimental conditions and field conditions of drinking water treatment plants. We hope that the current review will aid in the understanding of current research needs in the field of microplastic removal in drinking water treatment.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.828-837
• /
• 2006

Geotextiles consist of three major types of geosynthetic material (woven, non-woven and composite) and the functions of geotextiles are separation, reinforcement, filtration, drainage and as a moisture barrier. Although the many research scholar and engineer developed and established the design criteria and construction methodology, sustainable research still needed for optimum design methodology to the complicate field conditions. In this study, in-situ rainfall test performed to develop suitable filter system for sea dyke upper slope filter layer. In-situ rainfall test conducted for seven different filter system and measured the infiltration flux and pore pressure at various filter layer. Based on the test results, the double layered geotextile filter and sand transition system is most suitable for sea dyke upper filter layer because which system is effective for drainage of infiltration flow and minimize the deformation of sea dyke cover stone.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1554-1561
• /
• 2005

Geotextiles form one of the two largest groups of geosynthetics and it is consisted two major types of synthetic material (Woven, Non-woven). The functions of geotextiles are separation, reinforcement, filtration, drainage and as a moisture barrier. Within these functions, however, there are a large number of applications or use areas. Although the many research scholar and engineer developed and established the design criteria and construction methodology of geosynthetics filter layer, because the lack of suitable design terminology and uncertainty of long term durability, sustainable research still needed for optimum design methodology to the complicate field conditions. Especially, more intensive research needed about under the cyclic flow condition and fine silty sand base material. In this paper, the filter model test performed under cyclic flow with various boundary conditions (period and frequency of cyclic flow, types of geosynthetic filter material, surcharge etc.).

• Journal of Korean Society on Water Environment
• /
• v.21 no.2
• /
• pp.132-140
• /
• 2005

The pilot test of a new alternative for small wastewater treatment system has been conducted for two years. It consists of a hybrid bioreactor and the expert system including the process control logic, PLC system, and HMI for the process automation. In order to monitor and remote control its status, the real-time data was transferred from the on-site control center to the central station via a wireless local area network. More efficient and stable performances were observed at automatic operating mode compared with the manual. On an average, COD, SS, T-N and T-P concentrations in the effluent from the hybrid bioreactor were less than 14, 7, 12 and 0.9 mg/L, respectively. According to the result from pilot tests, the quality of treated wastewater with sand filtration was enough to be utilized again.

• Journal of Korean Society on Water Environment
• /
• v.25 no.4
• /
• pp.597-605
• /
• 2009

Algae bloom occurred in reservoir in summer can cause taste and odor in water and disturb the flocculation and sedimentation processes in water treatment plant and cause sand filter plugging. It was also reported that microcystins, anatoxin and saxitoxin released from cyanobacteria had acute toxic effects on liver and nervous system. For these reasons, many advanced countries inclusive of WHO set the guideline for these toxins and cyanotoxins have been managed with regular monitoring in Korea as well. However, complex sample preparation steps such as a solid phase extraction (SPE) and derivatization are required with an existing analysis method with HPLC. We needed to improve an analysis method for low extraction efficiency and long sample preparation time. In this study, we have established a new LC/MS/MS method which can simultaneously determine 6 cyanotoxins (Microcystins-LR, Microcystins-RR, Microcystins-YR, Anatoxin-a, Saxitoxin, Neosaxitoxin) with only simple filtration step. When $75{\mu}L$ filterated sample was injected onto the LC-MS/MS, the recovery ranged from 86% to 112% and the MDL was $0.025{\sim}0.581{\mu}g/L$. We can make the MDL be lower than the guideline ($1{\sim}3{\mu}g/L$) of advanced countries with simple preparation.

• Journal of Korean Society on Water Environment
• /
• v.22 no.1
• /
• pp.59-65
• /
• 2006

The effluent limitations for individual industry based on the best available technology economically achievable (BAT) have been required to achieve effective regulation. BAT assessment criteria that are suitable for the circumstances of Korean industry were developed in the previous study. The criteria were applied to determine the BAT for petrochemical basic compound manufacturing (PBCM) and plastics and synthetic resins manufacturing (PSRM) industry. Wastewater discharged from the each category contains high concentration of COD and toluene. Eighteen sites were surveyed and wastewater qualities were analyzed. Six and two different technologies were applied to the PBCM and PSRM industry for the end-of-pipe treatment process, respectively. The technology candidates were evaluated in terms of environmental impacts, economically achievability, treatment performance and economical reasonability. As the result, the technology options: typical activated-sludge process + sand filtration + activated carbon adsorption (PBCM) and wet oxidation + chemical precipitation + typical activated-sludge process + chemical precipitation (PSRM) were selected as the BAT for each industry.

• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.664-669
• /
• 2019

In this paper, a water-based green polymer mud is synthesized by simple compounding method. Effects of different kinds of tackifiers, their molecular weight on the viscosity of polymer mud and the effects of different fluid loss additives on mud fluid loss are studied. The results show that when polystyrene and anionic polyacrylamide with molecular weight of 8 ~ 10 million are used as the main thickening ingredient, polymer mud with high viscosity and high stability can be obtained. When the prepared polymer mud is formulated as NPAM: PEO: Hydroxypropyl cellulose(HPC) : Water = 42:10:10:100000 (unit: kg), the viscosity can reach 20.6 s, the filtration loss in 7.5 min is 24 mL, and the sand content is only 0.1 %. Compared with traditional bentonite mud, the green environment-friendly polymer mud has the advantages of small amount of waste, low environmental pollution, and low pulping cost, and can meet the construction needs for most topography and geomorphology drilling engineering.