• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.1035-1040
• /
• 2001

Recently, Sea-sand containing high levels of chloride is being applied to on reinforced concrete structures due to the exhaustion of river-sand and environmental problems, which affects directly corrosion of rebar in the RC structures. In this paper, characteristics of corroded rebar before and after casting were studied. Test results showed that bond strength of rebar corroded after casting was decreased with increase of corrosion level more rapidly than that of rebar corroded before casting.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.533-536
• /
• 2003

The objective of in this study makes investigation into the characteristics of antiwashout underwater concrete as to mix proportion, casting and curing water through experimental researches. in this study, sea sand is blended with river sand, crushed sand is blended with river sand and sea sand as to investigate the quality change and characteristics of antiwashout underwater concrete with variation of blend ratio of sea sand and crushed sand(0, 20, 40, 60, 80, 100%). Higher compressive strength is measured following the order of river sand, sea sand, crushed sand regardless of age and casting condition. Except for case of using river sand, blended ratio of 40% is appeared on most compressive strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.941-946
• /
• 2001

In this study, three kinds of fine aggregate (river sand, sea sand, crushed sand) were used and four different s/a (38%, 40%, 42%, 45%) were applied separately to this experimental for get the conclusion written below. Regardless of kinds of fine aggregate and casting-curing condition, maximum unit weight is seen at 40% of s/a and also to be seen in case of crushed sand. It's for that specific gravity of crushed sand is bigger comparatively than river sand and sea snad's one. Compressive strength is measured river sand, crushed sand, sea sand by order of size ; Regardless of variation of s/3, casting-curing condition and age. Compressive strength recorded maximum when s/a is 42% whatever sort of fine aggregate are. As the result, according to references, the optimum s/a of underwater antiwashout concrete is 40% but in this study, from compressive strength of view, the optimum s/a of underwater antiwashout concrete is 42%.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.945-952
• /
• 2023

In this study, the sand casting process was applied to design the gating system and perform casting simulation in order to domestically produce the submarine mast cover. Based on simulation results, casting experiments were conducted to produce a soundness prototype. The design concept of the mast cover's gating system was based on the design of bell casting. By arranging eight tower-type gates in a circle at 45° intervals, the flow of melt flowing into each gate was uniform and did not mix with each other, and the velocity of melt was also uniform. The mast cover made of Ni-Al-Bronze alloy has no unfilled parts. However, small porosities and flow marks occurred on the surface in several places. Yield strength and ultimate tensile strength are 279.3 MPa and 675.7 MPa, respectively, and elongation is 21.2%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.195-196
• /
• 2006

Direct laser sintering (DLS) technology for the resign coated sand is one of attractive technologies to produce molds and cores for the foundry industry rapidly and cost effectively. The objective of this case study is to develop casting pilot models using computer simulation technology, DLS RP machine and industrial computed tomography. The proposed casting design was verified by the Z-Cast software in the fields of fluid flow and solidification during the casting process. Casting parts with aluminum alloy using the post-curing treated sand moulds and cores are accurate to dimension and defect free.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.3
• /
• pp.159-164
• /
• 1997

Non-alloyed and 1.0%Ni alloyed ductile cast iron were cast into the sand mold and metal mold, and finer graphite size was obtained in case of metal mold casting. Direct tempering after casting showed the slight increase of absorbed energy, which is largely due to the relieving of residual stress that is developed during casting. After austempering heat treatment, higher impact energy was obtained in case of metal mold casting than sand mold casting, which is due to the finer graphite size.

• Journal of Korea Foundry Society
• /
• v.3 no.2
• /
• pp.100-105
• /
• 1983

The mechanism of coal-dust action on inhibiting burn-on of Sand to iron castings was taken in consideration by means of casting test and thermal decomposition test. To compare the ability of inhibiting sand burn-on, test castings were produced in green sand moulds added three different coal-rusts. And quantitative determination of lustrous carbon and volatiles production for coal-dust samples were performed.The lustrous carbon production was in good agreement with the casting test result. But total voltiles production was relatively inefficient on hibiting sand burn-on to test castings.The lustrous carbon theory can be given to explain the mechanism which coal-dust inhibits sand burn-on to iron castings.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.2
• /
• pp.4-23
• /
• 2020

The purpose of this study was to explore the diversity of Korea's iron casting technology and to examine various casting methods. The study involved a literature review, analysis of artifacts, local investigation of production tools and technology, and scientific analysis of casting and cast materials. Bellows technology, or Bulmi technology, is a form of iron casting technology that uses bellows to melt cast iron before the molten iron is poured into a clay cast. This technology, handed down only in Jeju Island, relies on use of a clay cast instead of the sand cast that is more common in mainland Korea. Casting methods for cast iron pots can be broadly divided into two: sand mold casting and porcelain casting. The former uses a sand cast made from mixing seokbire (clay mixed with soft stones), sand and clay, while the latter uses a clay cast, formed by mixing clay with rice straw and reed. The five steps in the sand mold casting method for iron pot are cast making, filling, melting iron into molten iron, pouring the molten iron into the cast mold, and refining the final product. The six steps in the porcelain clay casting method are cast making, cast firing, spreading jilmeok, melting iron into molten iron, pouring the molten iron, and refining the final product. The two casting methods differ in terms of materials, cast firing, and spreading of jilmeok. This study provided insight into Korea's unique iron casting technology by examining the scientific principles behind the materials and tools used in each stage of iron pot casting: collecting and kneading mud, producing a cast, biscuit firing, hwajeokmosal (building sand on the heated cast) and spreading jilmeok, drying and biyaljil (spreading jilmeok evenly on the cast), hapjang (combining two half-sized casts to make one complete cast), producing a smelting furnace, roasting twice, smelting, pouring molten iron into a cast, and refining the final product. Scientific analysis of the final product and materials involved in porcelain clay casting showed that the main components were mud and sand (SiO₂, Al₂O₃, and Fe₂O₃). The release agent was found to be graphite, containing SiO₂, Al₂O₃, Fe₂O₃, and K₂O. The completed cast iron pot had the structure of white cast iron, comprised of cementite (Fe₃C) and pearlite (a layered structure of ferrite and cementite).

• Journal of Korea Foundry Society
• /
• v.4 no.4
• /
• pp.5-13
• /
• 1984

This paper is presented for showing the effect of cooling rate on dendrite arm spacing, correlated with the chilling power of molding materials (conventional plaster, foamed plaster, silica sand) and section thickness, and also showing relationship between dendrite arm spacing and mechanical properties for an aluminum - 8.6 percent silicon - 3.6 percent copper alloy. Local solidification time $(t_f)$ and secondary dendrite arm spacing (d) could be varied widely in accordance with the molding materials and casting thickness, and the following relationship is obtained: $d=9.4t_f\;^{0.31}$ A good correlation between dendrite arm spacing and mechanical properties such as ultimate tensile strength, yield strength, hardness was found, that is, mechanical properties decreased in a linear manner with increase in log of secondary dendrite arm spacing. Ultimate tensile strength in conventional plaster mold casting decreased by 15 percent comparing with the sand casting, where as in foamed plaster mold casting, it decreased by 30 percent comparing with the sand casting. From those results, it has been verified that DAS might be the most representative parameter for predicting mechanical properties varing with the different cooling condition.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.77-82
• /
• 1998

The Part of slot on rotary compressor which plays an important part of the reliability and performance is studied on machinability and the wear characteristics for the specimen made by sand mold and permanent mold. The experiment are used the face cutter of milling machine which make the processing surface like broaching process and rollblock wear test machine. Permanent-mold casting iron is not affected by variation of RPM of milling machine, but sand-mold cast-iron is improved to increasing RPM. Also sand-mold casting iron shows superior wear characteristic to permanent-mold casting iron. This results from harder matrix of pearlite structure and self-lubrication characteristics of graphite. And wear particles in tested oil show shape and size similar to severe wear particles of oil taken from rotary compressor. The material and surface condition of slot play important part of the reliability and performance.