• 한국생산제조학회지
• /
• 제20권4호
• /
• pp.401-406
• /
• 2011

This study presents the stress safety analysis of a cylinder, which is manufactured by a tempered ASTM D2, tempered SM45C and normalized SM45C materials, respectively. The inner diameter of three cylinder models are 85mm, 95mm, and 11 Omm and the total length of a cylinder is 2,365mm for a high pressure injection molding machine. The FEM computed results show that the inner diameter of 85mm with a thick thickness of 62.5mm may produce the injection pressure of 325MPa and the inner diameter of 110mm with 50mm thickness reduces up to the injection pressure of 220MPa because of a reduced thickness of a cylinder. These injection pressures are enough for a high pressure injection molding machine assembled by ASTM D2 cylinder. And also, an injection cylinder manufactured by a tempered SM45C material in which is low priee may produce 225MPa injection molding pressure and this may sufficiently endure stress safety compared to that of ASTM D2 cylinder material. Thus, this study recommends that tempered SM45C cylinder is appropriated for a mild injection molding machine as an alternative cylinder material when the safety strength and low prices are considered. But the normalized SM45C cylinder material does not meet a stress safety of yield strength in general.

• 한국수산과학회지
• /
• 제42권3호
• /
• pp.232-237
• /
• 2009

Norovirus surrogate (feline calicivirus) was inactivated by treatment at 50,000 psi for 60 sec by 6.8-$log_{10}TCID_{50}mL^{-1}$. Tissue obtained from oyster (digestive gland, gill and mantle) was qualitatively destroyed and distorted by treatment at pressure greater than 5,000 psi for 60 sec. High pressure treatment induced progressive changes in the color of the oyster adductor muscle. High pressure treatment effectively reduced norovirus surrogate but induced conformational changes in the tissue and color of oyster flesh.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.492-500
• /
• 2004

The purpose of this study is localization of safety relief valves fur Nuclear Service through technical development with overall design, fabrication, inspection, capacity certification test and functional qualification test of safety relief valves in accordance with KEPIC MN Code(or ASME Sec.III ). The safely relief valve is the important equipment used to protect the pressure vessel, the steam generator and the other pressure facility from overpressure by discharging the operating medium when the pressure of system is reaching the design pressure of the system. But we're depending on technology of the other country up to the present time. Because we don't have our own technologies, we have been spent the great time and money on installing and repairing safety relief valve at nuclear power plant. Therefore we have to achieve the development of safety relief valves for Nuclear Service with our own technologies.

• Nuclear Engineering and Technology
• /
• 제36권4호
• /
• pp.285-294
• /
• 2004

Pressure wave propagation in the discharge piping with a sparger submerged in a water pool, following the opening of a safety relief valve, is analyzed. To predict the pressure transient behavior, a RELAP5/MOD3 code is used. The applicability of the RELAP5 code and the adequacy of the present modeling scheme are confirmed by simulating the applicable experiment on a water hammer with voiding. As a base case, the modeling scheme was used to calculate the wave propagation inside a vertical pipe with sparger holes and submerged within a water pool. In addition, the effects on wave propagation of geometric factors, such as the loss coefficient, the pipe configuration, and the subdivision of sparger pipe, are investigated. The effects of inflow conditions, such as water slug inflow and the slow opening of a safety relief valve are also examined.

• 한국안전학회지
• /
• 제23권5호
• /
• pp.22-29
• /
• 2008

This paper provides the evaluation method for the pressure vessel with internal wall-thinning defect, which is based on ASME design criteria. Pressure vessel has wall-thinning partially and patch reinforcement has been attached for reliable operating. However, present partial wall thinning could be through wall thinning at the next inspection time with present corrosion progress speed. Therefore safety margin was calculated for various conditions from present wall-thinning condition to additive patch reinforced condition via two-dimensional and three-dimensional, geometrically linear FE analyses using elastic materials.

• 한국산학기술학회논문지
• /
• 제20권3호
• /
• pp.324-328
• /
• 2019

스포츠를 위해 제공되고 사용되는 몇 가지 전용 챔버가 공급되어 사용되고 있지만 스포츠 멀티 환경을 동시에 제공할 수 있는 다기능 올인원 챔버는 개발되지 않았다. 본 연구에서는 스포츠 다중 인공 환경 시스템에 사용할 수 있는 다중압력 (양 / 대기 / 음압) 일체형 챔버를 설계하였다. 키가 큰 사용자를 위해 공간을 넓힌 새로운 챔버 디자인을 제시 한 다음 최대 응력과 구조적 안전성검토를 통하여 챔버의 구조해석을 수행하였다. 목표로 하는 허용 압력 조건하에서 쉘과 출입구의 접합부에서 최대 응력이 발생했으며, 챔버 재료의 허용응력을 기준으로 하여 구조안전성 평가를 수행하였다. 다중 압력 일체형 챔버에 대하여 구조해석을 수행한 결과 양압과 음압 조건에 대한 최대 응력이 챔버 재료의 허용응력 보다 훨씬 작은 값이 발생되었으며, 구조안전성 평가 결과 안전율 2 이상을 만족하여 챔버의 최종 시제품의 설계가 구조적으로 안전하다는 것을 확인하였다.

• 한국가스학회지
• /
• 제9권3호
• /
• pp.32-37
• /
• 2005

LP가스나 도시가스시설의 저압 호스 체결에서 견고함과 기밀성을 높이기 위해 호스밴드를 사용한다. 본 연구에서는 호스밴드의 성능 파악과 안전한 체결 거리의 제시를 위하여 호스밴드에 대한 내압강도와 당김력을 측정하였다. 호스밴드의 체결력은 스프링밴드 보다는 귀형밴드에서 높게 나타났으며 최적의 호스밴드 체결거리는 호스접속 끝단부로부터 1${\~}$2 mm일 때에 우수한 것으로 파악되었다.

• 한국가스학회지
• /
• 제22권6호
• /
• pp.16-27
• /
• 2018

대한민국 정부에서 2014년부터 LPG배관망과 LPG소형탱크를 도시가스 공급망 개설이 어려운 산간이나 도서지역에 보급하는 사업을 시작했다. 마을단위와 군단위로 LPG집단공급시설을 설치하면서 기존의 가스공급 압력이 아닌 10배 이상의 높은 준저압(25kPa~100kPa)으로 소비자에게 공급하게 되면서 가스사고의 위험성이 높아졌다. 기존의 가스공급압력보다 10배 이상 높은 압력이기 때문에 가스가 누출 되었을 때 빠른 속도로 많은 양이 누출하게 된다. 이에 준저압 가스배관의 안전성 확보를 위해 과류차단밸브가 필요하게 되었지만, 국내에서는 준저압 매몰배관용 과류차단밸브가 미개발되어 있으며 보급 또한 되어 있지 않는 상황이다. 이에 한국가스안전공사에서는 과류차단밸브의 국산화를 위해 과류차단밸브를 기개발한 해외의 성능기준과 제품을 조사 중에 있으며, 과류차단밸브의 성능평가를 위해 성능시험설비를 구축하여 준저압 연료가스 매몰배관용 과류차단밸브를 연구 개발 중에 있다.

• 한국수소및신에너지학회논문집
• /
• 제31권5호
• /
• pp.453-458
• /
• 2020

In this study, ethylene-propylene-diene monomer (EPDM) rubbers reinforced with various particle size of carbon black were prepared and tested. We followed recently published CSA/ANSI CHMC2 standard "the test methods for evaluating material compatibility in compressed hydrogen applications-polyemr". Measurement of change in hardness, tensile strength and volume were performed after exposure to maximum operating pressure, 87.5 MPa, for 168 hours (1 week). Once EPDM was exposed to high-pressure hydrogen, the samples experience volume increase and degradation of the physical properties. Also, after the dissolved hydrogen was fully eliminated from the specimens, the hardness and the tensile properties were not recovered. The rubber reinforced with smaller sizes of carbon black particles showed less volume expansion and decrease of physical properties. As a result, smaller particle size of carbon black filler led to more resistance to high-pressure hydrogen.

• 한국안전학회지
• /
• 제30권6호
• /
• pp.48-55
• /
• 2015

A variety of safety issues were investigated for chemical reactors using a toluene solvent in case of a fire at small to middle scale chemical plants. The issues covered the operation of pressure-relieving valves and the subsequent discharges of the toluene to the atmosphere either directly or through an absorber, which represent the current practice at most small chemical plants. It was shown that the safety valve on the reactor may not operate within about twenty minutes after an external fire breaks out, but, once relieved, the toluene vapor released directly to the atmosphere may form a large explosion range on the ground. It was also shown that if the discharge is routed to an existing absorber used for the scrubbing of volatile organic compounds or dusts, the column may not operate normally due to excessive pressure drops or flooding, resulting in the hazardous release of toluene vapors. This study proposed two ways of alleviating these risks. The first is to ruduce the discharge itself from the safety valve by using adequate insulation and protection covers on the reactor and then introduce it into the circulation water at the bottom of the absorber through a dip linet pipe equipped with a ring-shaped sparger. This will enhance the condensation of toluene vapors with the reduced effluent vapors treated in the packing layers above. The second is to install a separate quench drum to condense the routed toluene vapors more effectively than the existing absorber.