• Journal of Advanced Navigation Technology
• /
• v.14 no.1
• /
• pp.11-19
• /
• 2010

In this paper, H-plane filtering-horn antenna operating at millimeter frequency band is proposed with embedded filter and three-layered dielectric lens for frequency selection and maintenance of main beam direction, respectively. The waveguide-typed filter and H-plane sectoral horn antenna are replaced with considerably size-reduced PCB substrate-typed filtering antenna using via fences and several posts. The waveguide-typed filter and H-plane sectoral horn antenna were designed in air-filled waveguide and then combined into size-reduced PCB substrate. For the control of the thickness of dielectric lens, single and multi dielectric lens have been employed. As a result of antenna gain, 8 and 13.5 dBi have been obtained at 41.5 GHz, respectively, from the simulations of single and multi-lens antennas.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1532-1536
• /
• 2007

A plastic substrate with tiny rectangular pillars less than 100nm is injection molded to study pattern replication in injection molding. The size of the substrate is 50mm ${\times}$ 50mm and 1mm thick. The substrate has 9 patterned areas of which size is 2mm ${\times}$ 2mm respectively. The lengths of the pillars are 50nm, 100nm, 150nm and 200nm and the width and height are 50nm and about 100nm respectively. A pattern master is fabricated by e-beam writing using positive PR(photo resist) and then a nickel stamper replicated from the PR master by nickel electro-plating. Cr is deposited on the PR pattern master before nickel electro-plating as a conducting layer. Using this nickel stamper, several injection molding experiments are done to investigate effects of the injection molding parameters such as mold temperature, injection rate, packing pressure or pattern location on the replication of the patterns under 100nm.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.3
• /
• pp.31-36
• /
• 2002

The 2nd level solder joint reliability of 153 FC-BGA for high-speed SRAM (Static Random Access Memory) with the large chip on laminate substrate comparing to PBGA(Plastic Ball Grid Array) was studied in this paper. This work has been done to understand an influence as the mounting with single side or double sides, structure of package, properties of underfill, properties and thickness of substrate and size of solder ball on the thermal cycling test. It was confirmed that thickness of BT(bismaleimide tiazine) substrate increased from 0.95 mm to 1.20 mm and solder joint fatigue life improved about 30% in the underfill with the low young's modulus. And resistance against the solder ball crack became twice with an increase of the solder ball size from 0.76 mm to 0.89 mm in solder joints.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.15-18
• /
• 2008

To achieve high transport current without degradation under magnetic field, it is essential to artificially generate the pinning sites at which moving magnetic flux can be pinned. In this work, $ZrO_2$ nanodots were formed on the substrate surface using electro-spray deposition method. On top of the nanodots, the extended and effective pinning centers can be created. The positively charged Zr precursor solution was sprayed out from the needle using the corona discharge phenomena. Then, the sprayed precursor was deposited onto the negatively charged substrate surface followed by the heat treatment under the controlled atmosphere. Using the electrostatic force among the charged particles of precursor, evenly distributed and nano-sized dots were formed on the substrate surface. The size and density of the nanodots were studied by Atomic Force Microscopy. Also discussed are the effect of the deposition time and solution concentration on the size and density of the nanodot and processing variables in electro-spray method for the effective flux pinning centers in the superconducting films.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.142-142
• /
• 2011

Epitaxial $CuCrO_2$ thin films have been grown on single crystal substrate of c-plane $Al_2O_3$, $SrTiO_3$, YSZ and Quarts by laser ablation of a $CuCrO_2$ target using 266nm radiation from a Nd:YAG laser. X-ray measurements indicate that the $CuCrO_2$ grows epitaxially on all substrate, with its orientation dependent on the kinds of substrates. Most of the layer were polycrystalline with (001), (015) and random as the dominant surface orientation on c-plane YSZ, $SrTiO_3$ and quarts substrate, respectively. (001) orientated $CuCrO_2$ grows on C-plane $Al_2O_3$ and YSZ substrate, (015) orientated $CuCrO_2$ films are found on c-plane $SrTiO_3$ substrate and random orientated $CuCrO_2$ films grows on quarts substrate. These data are compared with the in-plane orientation and the mismatch of the $CuCrO_2$ and each substrate lattices in an attempt to relate the preferred orientation to the plane of the sapphire on which it is grown. Further characterization show that the grain size of the films increases for a substrate temperature increase, whereas the electrical properties of $CuCrO_2$ thin films depend upon their crystalline orientation.

• Journal of the Microelectronics and Packaging Society
• /
• v.5 no.2
• /
• pp.53-58
• /
• 1998

Sintering and dielectric characteristics of substrates were estimated by mixing rate of alumina and potashborosilicate glass(PBSG) powders. PBSG powders were used 7761(corning code)and alumina powders were used in extra pure rate(99.9%) and had 0.1 ${\mu}$m mean size. After ball milling with organic additives green sheets which were casted by doctor blade machine were sintered at 800$^{\circ}C$ for 1∼3hrs. Microstructure, linear shrinkage and dielectric constant of substrates were surveyed in order to fabricate low-dielectric and low tem-perature sintering substrate.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.08a
• /
• pp.42-43
• /
• 2000

Aspheric optical elements can provide an advantage in the design of optical system that require high performance and small size. The main disadvantage of high volume production of aspheric optical elements is very high cost. In this paper, we suggest new technology of high volume production process using replication process. The replication is a thin film of UV cured resin on a solid substrate blank(polymer substrate) with aspheric surface.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.315-316
• /
• 2001

In this study various nutritional and environmental parameters such as, initial moisture content, pH. inoculum size, air rate, sample size and nutrient supplement that influence pigment production were evaluated in solid-state cultures. optimum initial moisture content and pH were determined to be 50% and 6.0, respectively. The supplement of the substrate with different carbon, nitrogen, and mineral source reveals a more inhibitive effect as the substrate concentration increase. optimum aeration rate was determined to be 2vvm in flask culture. The maximum amount of red pigment, 3500 OD/g dried fermented rice, was obtained in optimum conditions which is obtained in solid flask culture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.180-182
• /
• 1997

GaN crystals were deposited by tile direct reaction between ammonia and gallium at 105$0^{\circ}C$, 107$0^{\circ}C$ and 110$0^{\circ}C$ on (0001) plane sapphire substrate. The size of GaN crystals were increased with reaction temperature, but its were decreased with increasing the flow rates of NH$_3$. The size of GaN of 46${\mu}{\textrm}{m}$ were deposited ell sapphire substrate at the reaction temperature of 107$0^{\circ}C$ for growth time of 60 min.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.319-322
• /
• 2004

ZnO nanostructures were formed on a Si substrate by off-axis pulsed laser deposition(PLD) system in which a substrate plane was tilted toward a plume propagation direction. Atomic force microscopy (AFM) showed islands of 20∼40 nm width. From the x-ray diffraction (XRD) pattern exhibiting only (002) ZnO peak, the islands observed in AFM image were found to well crystallized. Optical bandgap enlargement from 3.26 eV to 3.35 and 3.47 eV due to the quantum size effect of ZnO nanostructures were observed by Photoluminescence (PL) at room temperature.