• Corrosion Science and Technology
• /
• 제6권1호
• /
• pp.18-23
• /
• 2007

DLC coatings have been deposited onto substrate of STS 316L and Ti alloy using r.f. PACVD (plasma-assisted chemical vapor deposition) with a mixture of $C_{6}H_{6}$ and $SiH_{4}$ as the process gases. Corrosion performance of DLC coatings was investigated by electrochemical techniques (potentiodynamic polarization test and electrochemical impedance spectroscopy) and surface analysis (scanning electron microscopy). The electrolyte used in this test was a 0.89% NaCl solution of pH 7.4 at temperature $37^{\circ}C$. The porosity and protective efficiency of DLC coatings were obtained using potentiodynamic polarization test. Moreover, the delamination area and volume fraction of water uptake of DLC coatings as a function of immersion time were calculated using electrochemical impedance spectroscopy. This study provides the reliable and quantitative data for assessment of the effect of substrate on corrosion performance of Si-DLC coatings. The results showed that Si-DLC coating on Ti alloy could improve corrosion resistance more than that on STS 316L in the simulated body fluid environment. This could be attributed to the formation of a dense and low-porosity coating, which impedes the penetration of water and ions.

• 한국산업융합학회 논문집
• /
• 제25권5호
• /
• pp.783-789
• /
• 2022

In this study, STS316L rolled at five rolling degrees were treated with two types of subzero temperatures for 10, 30, and 60 minutes, respectively, and the dominant frequencies of elastic waves was investigated. The dominant frequency was higher as the subzero temperature was lower and the subzero treatment time was longer at each rolling degree. On the other hand, the dominant frequency was higher as the elongation decreased. In the time-frequency analysis for subzero temperature and time of the specimen with a rolling degree of 33%, the dominant frequency was higher at a subzero temperature of -196℃ than -50℃ regardless of subzero treatment time.

• 한국표면공학회지
• /
• 제50권4호
• /
• pp.259-265
• /
• 2017

5000 series aluminium alloys and austenitic stainless steels have excellent corrosion resistance and sufficient strength, which are widely used as materials for marine equipment and their parts in the marine environment. The corrosion characteristics of materials are important factors for selecting the appropriate material due to fluid component changes in the estuarine and coastal areas where seawater and fresh water are mixed. Therefore, for 5083 Al alloy, STS304 and STS316L widely used in the marine environment, anodic polarization experiments were performed to compare the corrosion damage characteristics of each material by three kinds of solutions of 100 % tap water, 50 % tap water+50 % natural seawater and 100 % natural seawater. As a result of the anodic polarization experiments, aluminum alloy (5083) caused locally corrosion on the surface in the tap water, and corrosion damage occurred all over the surface when the seawater was included. Stainless steels (STS304 and STS316L) presented almost no corrosion damage in tap water, but they grew pitting corrosion damage with increasing seawater concentration. STS316L showed better corrosion resistance than STS304.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.56-63
• /
• 2012

본 연구에서는 가공된 오스테나이트계 STS 316L ASME 표준 교정시험편을 이용하여 튜브 두께 감소율과 잔존두께에 대한 와전류 신호와 IRIS 신호특성을 비교하여 리보일러 튜브의 현장 적용성을 평가하였다. 그 결과 두께감소율의 경우 와전류탐상검사는 $20%{\times}4$ 평저공, 10% 외면 그루브, IRIS는 80%홈, 10%외면 그루브에서 ${\pm}15%$ 이상의 편차가 발생하였다. 잔존두께의 경우 와전류탐상은 측정치가 모두 허용범위를 만족하였으나, IRIS는 80% 인공홈에서 ${\pm}15%$ 이상의 편차가 발생하였다. 따라서 와전류탐상검사 후 의사지시에 대한 해석, 두께감소율 측정을 위해 IRIS를 수행한다면 신뢰성이 향상될 것으로 판단된다.

• 한국분말재료학회지
• /
• 제20권6호
• /
• pp.432-438
• /
• 2013

In this study, analysis on the oxidation behavior was conducted by a series of high-temperature oxidation tests at both $800^{\circ}C$, $900^{\circ}C$ and 1000 in the air with sintered STS 316L. The weight gain of each oxidized specimen was measured, the oxidized surface morphologies and composition of oxidation layer were analyzed with Scanning Electron Microscope-Energy Dispersive x-ray Spectroscopy (SEM-EDS), finally, the phase change and composition of the oxidized specimen were shown by X-Ray Diffraction (XRD). As a result, the weight gain increased sharply at $1000^{\circ}C$ when oxidation test was conducted for 210 hours. Also, a plentiful of pores were observed in the surface oxidation layers at $900^{\circ}C$ for 210 hours. In addition, the following conclusions on oxidation behavior of sintered STS 316L can be obtained: $Cr_2O_3$ can be formed on pores by influxing oxygen through open-pores, $(Fe_{0.6}Cr_{0.4})_2O_3$ can be generated on the inner oxidation layer, and $Fe_2O_3$ was on the outer oxidation layer. Also, $NiFe_2O_4$ could be precipitated if the oxidation time was kept longer.

• 한국분말재료학회지
• /
• 제24권3호
• /
• pp.210-215
• /
• 2017

In this study, STS316L powders prepared by gas atomization are used to manufacture bulk structures with dimensions of $10{\times}10{\times}10mm^3$ using selective laser melting (SLM). The microstructures and hardness of the fabricated 316L stainless steel has been investigated with the laser beam overlap varied from 10% to 70%. The microstructures of the fabricated STS316L samples show a decrease in the balling and satellite of powders introducing defect in the bulk samples and the porosity caused by the gap between the molten metal pools disappearing as the overlap ratio increases, whereas a low overlap ratio results in significant balling and a large amount of isolated powders due to the increased gap between the melt pools. Furthermore, the highest value in Vickers hardness is obtained for the sample fabricated by 30% overlapped laser beams. These results show that the overlap ratio of laser beams in the SLM process should be considered as an important process parameter.

• International Journal of Automotive Technology
• /
• 제1권2호
• /
• pp.71-77
• /
• 2000

High temperature materials in service are subjected to mechanical damage due to operating load and metallurgical damage due to operating temperature. Therefore, when designing or assessing life of high temperature components, both factors must be considered. In this paper, the effect of tensile hold time on high temperature fatigue crack growth and long term prior thermal aging heat treatment on creep rupture behavior were investigated using STS 316L and STS 316 austenitic stainless steels, which are widely used for high temperature components like in automotive exhaust and piping systems. In high temperature fatigue crack growth tests using STS 316L, as tensile hold time increased, crack growth rate decreased in relatively short tensile hold time region. In long term aged specimens, cavity type microcracks have been observed at the interface of grain boundary and coarsened carbide.

• 전기화학회지
• /
• 제9권2호
• /
• pp.70-76
• /
• 2006

마이크로 전기화학 실험법인 비접촉식 미세방울셀이 산 용액에 노출된 저 크롬이 함유된 스테인리스강(STS 316)과 같이 젖음성이 높은 전기화학계에 사용되는데 어려움이 있었다. 음압의 인가, 방울의 크기 제어 그리고 소수성의 개스킷의 사용은 높은 젖음성을 지닌 표면에서 비접촉식 미세방울셀의 적용을 가능하게 하였다. 개선된 미세방울셀의 신뢰성을 확인하고자 3종류의 다른 계-산성염화용액과 고 크롬 페라이트 스테인리스강, 산성염화용액과 STS 316 그리고 중성염화용액과 STS 316-에 대하여 개선된 미세방울셀로 국부부식 연구를 수행하였다. 첫째 산성용액에서 고 크롬강의 양극 분극 결과는 $\alpha/\sigma$ 계면 근처에서 국부부식이 크롬 고갈층에 의한 것임을 보여주었다. 둘째 산성용액에서 STS316의 양극 분극실험이 개선된 미세방울셀에서 성공적으로 수행됨을 확인할 수 있었다. 특히, 미세방울셀에서 얻어진 국부 양극 분극곡선을 통해 STS316의 내식성에 미치는 $\delta$-라이트 영향을 밝힐 수 있었다. 마지막으로 중성염화 용액에서 STS316의 양극 분극곡선은 핏팅 저항성이 $\delta$-페라이트보다 개재물에 의존됨을 보여주었다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.258-263
• /
• 2001

In this paper, the real-time prediction of high temperature creep life was carried out for the friction welded joints of dissimilar heat resistintg steels (CulCr0.5Zr-STS316L). Various life prediction methods such as LMP (Larson-Miller Parameter) and ISM (initial strain method) were applied. The creep behaviors of those steels and the welds under static load were examined by ISM combined with LMP at 300, 400 and 50$0^{\circ}C$, and the relationship between these two methods was investigated. A real-time creep life (tsub/r/, hr) prediction equation by initial strain ($\varepsilon_0$, %) under any creep stress ($\sigma$, MP$\alpha$) at any high temperature (T, K) was developed

• 한국해양공학회지
• /
• 제29권6호
• /
• pp.475-480
• /
• 2015

In this study, we developed a Cr-free organic/inorganic hybrid solution and investigated its coating properties on degraded STS316L. Both the OIBD-1 solution and OIBD-2 solution had excellent corrosion resistance and adhesion ability. However, the solution had some problems in a boiling water environment. In addition, the flexibility was excellent, and the scratch resistance was relatively good.