• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.480-485
• /
• 1999

The $SrTiO_3$ with Al, Pr red phosphor for FED was synthesized by Pechini process using metallic nitrates, ethylene glycol and citric acid. The different particle growth tendency of $SrTiO_3$ phosphor powder was observed at above and below $900^{\circ}C$. Also, luminescent properties were observed under 359 nm excitation of Pr ion. The emission band was shown between 575 nm and 650 nm with 617 nm maximum spectra. Therefore, $SrTiO_3$ with Al, Pr phosphor is applicable to red phosphor of FED.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.9
• /
• pp.724-727
• /
• 2009

We have fabricated (Ba,Sr)TiO3$TiO_3$ thick films doped with various amount of ZnBO dopants (1, 3, and 5 wt%) by screen printing method on the alumina substrates, which were sintered at the temperature below $1200^{\circ}C$. With increasing the amount of ZnBO dopants, the relative dielectric permittivity of ZnBO doped (Ba,Sr)$TiO_3$ was decreased, while loss tangent was increased. 1 wt% ZnBO doped (Ba,Sr)$TiO_3$ thick film has relative dielectric permittivity of 759 at 1 MHz, while 3 and 5 wt% of ZnBO doped (Ba,Sr)$TiO_3$ thick films have 624 and 554, respectively. By introducing ZnBO dopants to the (Ba,Sr)$TiO_3$ thick films, leakage current densities were decreased. The decreased leakage current with increasing ZnBO dopants can be explained by increased density and grain size of thick film on alumina substrate. We believe this decreased leakage current density probably come from the increased grain size and increased density.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.317-321
• /
• 2003

In this study, the structural properties were Investigated for the deposited (Ba,Sr)(Nb,Ti)O$_3$[BSNT] thin films grown on Pt/TiO$_2$/SiO$_2$/Si substrate by RF sputtering method. The structural properties of the BSNT thin films affected by the Ar/02 ratios were Investigated. In the case of the BSNT thin films deposited with condition of 60/40(Ar/O$_2$) ratio, the BaTiO$_3$, SrTiO$_3$ and BaNbO$_3$ phases were showed. The composition ratio of Nb and Ti in the BSNT thin films were nearly equivalent. Also, in the BSNT thin films deposited with condition of 60/40 and 80/20(Ar/O$_2$) ratios, the composition of Ba, Sr, Nb and Ti were relatively uniform. The Ba, Sr, Nb and Ti in the BSTN thin films were not diffused into the Pt layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.931-939
• /
• 1998

Preparation of the hexagonal Sr-ferrite powsers with high performance by co-spraying precusor of the FeCl$_2$+SrCO$_3$ at a low temperature was proved as a cost =-effective method. The co-spray roasting was carried out in the temperature range of 300~$700^{\circ}C$ after SrCO$_3$ powders were mixed into 12FeCi$_2$.4$H_2O$ liquor. By this low temperature roasting method fine particles of multi-phased FeO$_2$+SrCO$_3$ were formulated. Powders calcined at 105$0^{\circ}C$ for 1 hour show the best magnetic property of M\ulcorner=69.96 emu/g, M\ulcorner=36.98 emu/g, and \ulcornerH\ulcorner=4.31 Oe. This calcining temperature is lower than that of the conventional dry method by 10$0^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.4
• /
• pp.78-89
• /
• 2012

The generated torque of a switched reluctance(SR) motor is highly nonlinear, which makes it difficult to determine the reference current commands for minimum torque ripples. In this paper, we present a computationally simple and efficient method to minimize torque ripples of SR motors based on iterative learning control. The reference current command of each phase minimizing torque ripples is identified in 2-dimensional look-up table form. Our learning control algorithm does not require the torque model, so our method is not affected by model errors and hence is very accurate. In order to justify our work, we present some computer simulation results.

• Korean Journal of Environmental Agriculture
• /
• v.22 no.4
• /
• pp.290-293
• /
• 2003

To measure an effects of strontium on secretion of ${\alpha}$-amylase and RNase, wheat aleurone layers were isolated after the pre-incubation in a solution with or without 10 mM $SrCl_2$ or $CaCl_2$ for 3 days at $25^{\circ}C$ in the dark under aseptic conditions. The secretion of ${\alpha}$-amylase reached a maximum at 72 h after incubation. $Sr^{2+}$ induced more effectively secretion of ${\alpha}$-amylase than $Ca^{2+}$. The ${\alpha}$-amylase secretions by $Sr^{2+}$ or $Ca^{2+}$ ware about $2 (Ca^{2+})$ to $2.5 (Sr^{2+})$ fold higher than it without divalent ions, When aleurone layers were incubated without divalent ions, however, the ${\alpha}$-amylase was remarkably retained in the tissues. Total ${\alpha}$-amylase synthesis (ie. tissues + media) was slightly lowered by 10mM $SrCl_2$ addition. It seemed that the RNase secretion begins at 18 h after incubation. This meaned that the RNase secretion may process slower than ${\alpha}$-amylasee secretion. $Ca^{2+}$ effect on RNase secretion is stronger than $Sr^{2+}$ unlikely to ${\alpha}$-amylase. The secretion process is likely to be suddenly induced between 72 hand 96 h. These results suggested that the secretion was enhanced after the accumulation in aleurone layers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.284-287
• /
• 2001

Multi-pole anisotropic Sr-fertile sintered magnets has been studied by powder injection molding under applied magnetic field. The orientation of anisotropic Sr-ferrite powders higher than 80% during injection molding is achieved at the following conditions; apparent viscosity lower then 2500 poise in 1000 sec$\^$-1/ shear rate and applied magnetic field higher then 4 kOe. For the high fluidity and strength of injection molded compact, and the effective binder removal without defects during solvent extraction and thermal debinding, the optimum multi-binder composition is paraffin wax(PW)/carnauba wax(CW)/HDPE = 50/25/25 wt%. The rate of binder removal is proportional to the mean particle size of Sr-ferrite powders whereas it is inversely proportional to the content of Sr-ferrite powders and the sample thickness. The high magnetic properties of Sr-ferrite sintered magnets are; 3.8 kG of remanent flux density, 3.4 kOe of intrinsic coercivity, and 1.2 kG of surface flux density (1-mm-thick) in the direction of applied magnetic field.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.843-846
• /
• 2000

The (1-x)MgTiO$_3$-xSrTiO$_3$(x=0.02∼0.08) ceramics were fabricated by conventional mixed oxide method. The sintering temperature and time were 1250$^{\circ}C$∼1400$^{\circ}C$, 2hr., respectively. The structural and microwave dielectric properties were investigated by varying sintering temperature and composition ratio. In the (1-x)MgTiO$_3$-xSrTiO$_3$(x=0.02) ceramics, the cubic SrTiO$_3$and hexagonal MgTiO$_3$phases were coexisted. The dielectric constant was increased and the temperature coefficient of resonant frequency( $\tau_f$) was decreased with addition of SrTiO$_3$. The temperature coefficient of resonant frequency($\tau_f$) was gradually varied from negative value to positive value with increasing the SrTiO$_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.268-269
• /
• 2007

In this study, the structural and microwave dielectric properties of the $Sr_5Nb_4O_{15}$ cation-deficient perovskite ceramics with sintering temperature were investigated. All sample of the $Sr_5Nb_4O_{15}$ ceramics were prepared by the conventional mixed oxide method and sintered at $1350^{\circ}C{\sim}1500^{\circ}C$. The bulk density, dielectric constant and quality factor of the $Sr_5Nb_4O_{15}$ ceramics were increased with increasing sintering temperature. In the case of the $Sr_5Nb_4O_{15}$ ceramics sintered at $1500^{\circ}C$ for 5h, the dielectric constant, quality factor and temperature coefficient of the resonant frequency (TCRF) were 22.35, 16,577GHz, +13.40ppm/$^{\circ}C$, respectively.

• Korean Journal of Microbiology
• /
• v.34 no.4
• /
• pp.243-247
• /
• 1998

Comparative analyses of intracellular biopterin contents and its biosynthetic enzymes were performed in Allomyces macrogynus. Biopterin content in fresh weight was 14-fold higher in mycelium than in zoospore. Enzyme activities of GTP cyclohydrolase I and 6-pyruvoyltetrahydropterin synthase in ammonium sulfate fractions were approximately 2-fold higher in mycelium. On the other hand, sepiapterin reductase (SR) activity was 10 fold higher in zoospore. Northern blot assay also demonstrated that SR transcript was abundant in zoospore. These results suggest a possible involvement of tetrahydrobiopterin in cellular differentiation of Allomyces macrogyllus as well as provide an experimental basis to elucidate the physiological function of SR in this organism.