• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.1163-1165
• /
• 2010

가솔린 기관의 체적 효율은 흡기 장치의 효율의 척도로 표현된다. 현재 체적효율은 4행정 가솔린 엔진의 흡기장치의 특성과 공연비 제어를 위한 중요한 파라미터로 사용되고 있다. 체적 효율은 이론적으로 실린더로 흡입 가능한 양에 대한 실제로 실린더로 흡인한 공기량의 비율이다. 체적효율은 엔진회전 속도와 흡기다기관 부압에 따라 결정되는 종속변수이다. 체적 효율은 정상상태와 과도상태와 같은 엔진의 모든 운전조건을 시험하는데 한계와 제약이 매우 크다. 이 논문에서는 선형 알고리즘을 사용하여 체적 효율의 파라미터를 규명하여 선형 다항식 모델을 개발한다. 그리고 실험으로 구한 체적효율 데이터와 다항식 모델을 비교하고 객관적인 타당성을 평가 하였다.

• Journal of Ceramic Processing Research
• /
• v.19 no.6
• /
• pp.450-454
• /
• 2018

In recent years, thermal insulation coating technology for automotive engine parts has received significant attention as a means of improving the thermal efficiency of automotive engines. One of the characteristics of thermal insulation coatings is their low thermal conductivity, and, materials such as YSZ (Yttria-stabilized zirconia), which have low thermal conductivity, are used for this purpose. This research presents a study of the changes in the microstructure and thermal conductivity of $8YSZ/SiO_2$ multi compositional thermal insulation coating for different compositions, and particle size distributions of suspension, when it is subjected to suspension plasma spraying. To obtain a porous coating structure, the mixing ratio of 8YSZ and $SiO_2$ particles and the particle sizes of the $SiO_2$ were changed. The microstructure, phase formation behavior, porosity and thermal conductivity of the coatings were analyzed. The porosities were found to be 1.2-32.1%, and the thermal conductivities of the coatings were 0.797-0.369 W/mK. The results of the study showed that the microstructures of the coatings were strongly influenced by the particle size distributions, and that the thermal conductivities of the coatings were greatly impacted by the microstructures of the coatings.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.6
• /
• pp.331-339
• /
• 2021

Environmental barrier coatings(EBCs) are applied to the SiC/SiC ceramic matrix composites(CMCs) in order to protect CMCs from being corroded with water vapor by combustion gas in gas turbine engines. Ytterbium silicates, such as ytterbium monosilicate and ytterbium disilicate, are ones of the candidate materials for EBCs due to their excellent resistance to water vapor corrosion as well as thermal-expansion match with SiC. In this study, ytterbium silicates are fabricated with 2-step solid-state synthesis targeting ytterbium disilicate. After synthesizing ytterbium monosilicate, the mixtures of ytterbium monosilicate and SiO₂ are heat-treated and densified by using pressureless sintering or hot pressing with a variety of heating conditions. The phase formation, thermal expansion, and oxidation behavior are examined with fabricated specimens. The final densified bodies are found to be composites between ytterbium monosilicate and ytterbium disilicate with different ratios, which results in 4.43 to 6.72×10^-6/K range of coefficients of thermal expansion. The probability of these ytterbium silicates for EBC applications is also discussed.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3282-3287
• /
• 2007

Lean combustion is one of the most promising method for increasing engine efficiency and reducing the exhaust emission from SI gas engines. Due to the possibility of partial burn and misfire, however, under lean burn operation, stable flame kernel formation and fast burn rate are needed to guarantee a successful subsequent combustion. Experiment data were obtained on a single-cylinder CNG fueled SI engine to investigate the effect of direct injection, spark timing and variation of injection timing. Experimental results show that lean burn limit is ${\lambda}$=1.3 with port injection, and expansion of lean burn limit ${\lambda}$=1.4 with direct injection method, due to increase of turbulence intensity in cylinder and stratified charge. Combustion duration in lean region is improved by using the variation of injection timing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.308-318
• /
• 1988

The liquid disintegration and characteristics of atomization through the swirl nozzle is affected by injection pressure and injection time when the liquid is injected intermittently. These transient phenomena are investigated by electronic controlled-fuel injection nozzle. The effect of injection conditions on disintegration of liquid injected through nozzle is observed photographically by using delay circuit. Droplet size of the element of the sample is measured by the liquid immersion sampling technique. SMD of droplets is varied with time and is decreased as the injection pressure increases. As the injection pressure increases, the maximum diameter of droplet and diameter of droplet which has the maximum droplet number decrease. Spray angle is not affected on injection pressure and change of spray angle with time is associated with needle movement.

• International Journal of Automotive Technology
• /
• v.5 no.4
• /
• pp.311-319
• /
• 2004

There are many methods to test engine emissions depending on the regulations used such as FTP-75(CYS-75) mode, 10-15 mode and ECE-15 mode. Most of these modes consist of transient conditions such as cranking, rapid acceleration or deceleration modes. In this experimental research, the transient characteristics including cranking and accelerating mode in SI engines were studied to compare pure gasoline with methanol-reformulated fuels for performance and exhaust emissions. The results show that methanol-reformulated fuels have a better emissions reduction rate than that of pure gasoline especially for HC, CO and NOx emissions during cranking mode. The acceleration performances conform to the results of the distillation curve and the CO concentration for RM50 varies slightly in acceleration mode.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.675-685
• /
• 2007

A single cylinder SI engine with a VVA system is modeled by the coupling of a commercial 1D simulation package and an additional combustion model and validated by comparison with experimental data. A number of simulations are carried out to investigate the effects of five different VVA systems on the performance and fuel efficiency of the baseline engine. Finally, the simulation model is applied to an extensive computational study to map out the strategies to operate the engines with dual CVVT and dual CVVT-2 step VVL systems in a fuel-efficient manner.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.1-8
• /
• 2001

The flow field inside a cylinder of four-valve Sl engine was investigated quantitatively using a three-dimensional Laser Doppler Velocimetry system, to determine how stroke changes affect the flow field. The purpose of this work was to develop quantitative methods which correlate in-cylinder flows to engine performance. For this study, the sane intake manifold, engine head, cylinder, and the piston were used to examine the flow characteristics in different strokes. Quantification of the flow field was done by calculating three major parameters which are believed to adequately characterize in cylinder motion. These quantities were TKE, tumble and swirl ratios. The LDV results reveal that flow patterns are similar, the flow velocities scale with piston speed but another parameters such as TKE, and tumble and swirl numbers are not the same for different stroke systems.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.45-57
• /
• 2007

This paper presents both experimental and numerical studies regarding nozzles used for the SI engine application, particularly for the intake-port fuel injection type. The atomization mechanism of the multi-hole plate nozzle was investigated experimentally. It was found that the nozzle design added turbulence into the liquid-film jet and the jet disintegrated rapidly. Based on the results, various plate types for the nozzle were developed and tested; six hole nozzle for liquid jet interaction, plate-type nozzle with flat duct channel, and the simpler structured nozzle. The spray characteristics of the prototype nozzles were examined experimentally while the internal flow of the nozzle was investigated computationally. It was shown that turbulent liquid-film was injected and atomization quality was improved by controlling the internal flow condition of the plate-type nozzle.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.4
• /
• pp.27-35
• /
• 1998

Ni-based heat resisting alloys are commonly used for high temperature applications such as in aircraft engines and gas turbines. In this work, the machinability of Nimonic 263 alloy is investigated with respect to optimum tool type and cutting conditions for both continuous and discontinuous machining as well as weld region. Among the five types of tools tested, K25 tool experienced the least of damage in machining the weld region. Furthermore, despite their superior high temperature hardness, Si-Al-O-N and CBN tools peformed poorly in machining Nimonic 263.