• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.157-170
• /
• 2002

The purpose of this study is to analyze the shear bond strength according to kinds of surface treatment agents and resin cements after acid etching of IPS Empress 2. For this purpose, test groups were classified into silane-treated bonding groups, silica-coated group and Targis link applied group. Then, nine bonding groups in total, each three groups per kind, were prepared by using three kinds of resin cements-Panavia F, Variolink II and Rely-X ARC, and thirty test specimens per group were prepared. To examine any changes in the oral environment, the shear bond strength of each test specimen was measured after dipping test for 24 hours and for five weeks, respectively, in distilled water at $37^{\circ}C$ and performing heat cycle 10,000 times in total, each 2,000 times per week, during a five weeks of dipping, under the condition similar to the oral environment. The bond failure modes were also observed by means of a scanning electron microscope. The results are summarized as follows 1. Statically significant differences between the surface conditioning materials were observed. The shear strength of the silane treatment was the highest of all three types of surface treatments(p<0.001). 2. Shear strengths varied significantly for different types of resin luting agents. But bond strength of Targis link surface treatments were not significantly different(p<0.05). 3. No significant difference of bonding strengths was found between storage time conditions(24 hours and 5 weeks). Only group II, IV, VII, IX were significantly different(p<0.05). 4. After thermocycling, the shear bond strengths of all groups were significantly decreased (p<0.05). Group III, V, VI were no significantly different. 5. On the SEM observation of fractured surfaces, all groups were shown complex failure.

• Korean Journal of Veterinary Research
• /
• v.32 no.2
• /
• pp.157-164
• /
• 1992

Changes in the both inward current and conductance of membrane by the fertilization were observed using the one microelectrode voltage clamp(or switch clamp) technique. Unfertilized eggs and both 1- and 2-cell stage eggs after fertilization were donated from the superovulated mouse (ICR, more than 6 weeks old) treated with PMSG(pregnant mare serum gonadotropin, Sigma) and HCG(human chorionic gonadotropin, Sigma) and naturally mated ones, respectively in this experiment. Membrane potential was held at -90mV and the voltage step was applied from -80mV to 50mV with interval of 10mV or 20mV for 300ms. since both of amplitudes and time courses in the membrane currents were various according to the states of cells and clamping condition, results were presented by their $averages{\pm}SEM$(standard mean error)and ratios or percentages. Inward currents began to appear in response to the step depolarization from -60mV and reached its maximum at -50mV. However, since the potential was not clamped evenly during the voltage step, current-voltage(I-V) relationship might be positively shifted 10 or 20mV. From the steady-state currents plotted in the I-V curve, outward rectification was markedly observed. Peak inward currents$(i_{in})$ at -50mV were $-0.62{\pm}0.23nA$(n=4),$-0.52{\pm}0.25nA$(n=5) and $-0.37{\pm}0.25nA$(n=6), in the 1-cell stage, 2-cell stage fertilized eggs and in the unfertilized eggs, respectively. Pure inward current (difference between steady-state and peak, $i_{in. pure}$) were $-1.01{\pm}0.23nA$, $-0.69{\pm}0.43nA$ and $-0.68{\pm}0.29nA$, respectively in the 1-cell stage fertilized eggs, unfertilized eggs and 2-cell stage fertilized eggs. These results suggested that the outward current in fertilized eggs of 2-cell stage was more increased than those in the unfertilized eggs. Pure inward currents in the all stages of eggs showed a similar fashion in the I-V relationship from -50mV to 50mV and reversal potential at 50mV. Time constant of inactivation$({\tau})$ in the inward current was decreased as the membrane potential was depolarized in the unfertilized and 2-cell stage eggs but in the 1-cell stage eggs t was not likely to be affected significantly. Slope conductances were 14.2nS, 8.9n5 and 7.7nS in the 1-cell, 2-cell stage fertilized eggs and the unfertilized eggs, respectively. Membranes between two cells within a zona pellucida seem to be electrical-connected in the 2-cell stage eggs from the observation made in the analysis for the electronic spread and decay to the current stimuli. Both of inward current and membrane conductance were increased after fertilization in the mouse eggs. Inward current seems to be carried by the same ion or through the same channels up to the 2-cell stage and ion that carried inward current was thought to play important function after fertilization in the mouse eggs.

• Journal of Life Science
• /
• v.17 no.9 s.89
• /
• pp.1284-1289
• /
• 2007

The Biological Activated Carbon (BAC) process in the water treatments represents a kind of biofiltration process which capabilities of bacteria to remove organic matters are maximized. It enables to eliminate organic matters and effectively reduce microbial regrowth potentials. As attached bacteria employ natural organic matter as a substrate, they are significantly dependent on indigenous microorganisms. In this study, characteristics of bacterial community by culturable and unculturable Methods have been conducted in a pilot plant using SAC in water treatment process at the downstream of the Nakdong River. Based on the results, HPC and bacterial- production for coal-based activated carbon material were $1.20{\sim}56.2{\times}l0^7$ cfu/g and $1.2{\sim}3.7\;mgC/m^{3}h$, respectively, in the SAC process. The highest level of attached bacteria biomass and organic carbon removal efficiency was found in the coal-based activated carbon. The genera Pseudomonas, Flavobacterium, Alcaligenes, Acilzetobacter, and Spingomonas were identified for each activated carbon material. Pseudomonas vesicularis was the dominant species in the coconut- and coal-based materials, where as Pseudomonas cepacia was the dominant species in the wood-based material. The Scanning Electron Microscope (SEM) observation of the activated carbon surface also found the widespread distribution of rod form and coccus. The community of attached bacteria was investigated by performing Fluorescent in situ hybridization (FISH) analysis. a group was dominant in coal, wood and coccunt-based materials, ${\alpha},\;{\beta}\;and\;{\gamma}$ group ranged from 27.0 ${\sim}$ 43.0%, 7.1 ${\sim}$ 22.0%, 11.3 ${\sim}$ 28.6%, respectively. These results suggest that a group bacterial community appears to be regulated removal efficiency of organic material in water treatment process.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.10
• /
• pp.1492-1503
• /
• 2015

This study evaluated the combination effect of various freezing and thawing techniques on the quality and nutritional aspects of onions. Onions were frozen by natural air convection freezing (NCF), air blast freezing (ABF), and liquid nitrogen freezing (LNF). Onions were frozen for 76 min by NCF, 9 min by ABF, and 9 min by LNF. The freezing treatment was stopped when the core temperature reached $-12^{\circ}C$ for NCF and ABF, and $-120^{\circ}C$ for LNF. Frozen samples were thawed through natural air convection thawing, running water thawing, sonication thawing (ST), or microwave thawing. The quality and nutritional aspects of frozen-thawed onions were evaluated by measuring thawing loss, pH, texture, water content, color, and SEM image. ST was found to cause the least loss in onion sample among the tested thawing methods, whereas the freezing methods did not cause any significant loss. In our experiment, thawing is found to be a more critical technique when compared to that of freezing. There were no clear quantifications or trends of pH and water content among different freezing and thawing techniques. The highest total color difference (${\Delta}E$) was observed in the NCF sample. For morphological observation, ABF gave the smallest ice crystal size, as well as minimum cell collapse. Loss of vitamin C, free sugar, and organic acid content was lower in the ABF and ST sample, when compared to other trials. In our study, we found that combination of ABF and ST could preserve the quality and nutritional aspects of frozen-thawed onions better than other methods.

• Journal of Conservation Science
• /
• v.26 no.2
• /
• pp.171-182
• /
• 2010

The slag excavated from Gyesil-ri in Gongju, Yeonje-ri in Cheongwon and Beopcheonsaji (temple) site in Wonju are analyzed by X-ray Fluorescence Analyzer, metallurgical microscope, SEM-EDS etc., for chemical composition and microstructure to figure out the raw material and the iron manufacturing technique. First of all, as a result of principal component analysis, the total Fe-content of slag from Gyesil-ri is 39 to 44% and the modified rate is 15 to 21%, which is common in ancient iron slag. Yeonje-ri site is found the ancient iron-smelting furnace. The total Fe-content of slag from Yeonje-ri is 41 to 43% and modified rate is 18~30%, which is also the general value in the ancient slag. However only slag is excavated in the residential area at Beopcheonsaji site and there is no iron making relic. In addition, the result of principal component analysis contains that the total Fe-content of Beopcheonsaji site is 52 to 57%, and modified rate is 8 to 14%. It shows that the total Fe-content of Beopcheonsaji site is higher than relic from Gyesil-ri and Yeonje-ri and the modified rate is lower than other sites. This results mean that recollecting rate of Fe in Beopcheonsaji site is lower than other sites. Also, as a result of minor elements analysis, the slag from Gyesil-ri has the higher level of Ti, V and Zr than other sites and the microstructure are observed as magnetite and ulvospinel, so that the raw material of slag is iron sand. But the slag from Yeonje-ri and Beopcheonsaji site are identified to use iron ore. As a result of microstructure observation, fayalite, gray-columnar crystal, is found in the slag from Yeonje-ri and big wustite as main phase is observed in the slag from Beopcheonsaji site. This study show that the slag from Yeonje-ri is made of smelt ash produced during smelting works and the slag from Beopcheonsaji site is made of forging ash produced during forging work concerning the excavated location and the microstructure.

• Parasites, Hosts and Diseases
• /
• v.23 no.2
• /
• pp.203-213
• /
• 1985

The in situ posture of anterior body of Metagonimus yokogawai was observed in experimental metagonimiasis of dog. The metacercariae were collected from naturally infected sweetfish by peptic digestion; a total of 8 dogs was orally infected with 10,000 metacercariae respectively. Two dogs were killed on 3 days, 9 days, 4 weeks and 10 weeks after the infection. The postures of worms in histological section of small intestine and of whole worms collected from the fixed intestinal mucosa were examined by light and scanning electron microscope. The results were summarized as follows: 1. The recovery rates of worms were 42.6% on 3 days, 55.0% on 9 days, 33.2% on 4 weeks and 9. 8% on 10 weeks after the infection respectively. 2. In histological sections of small intestine, most of worms were found at intervillous spaces as ovoid sections of posterior body. However, many worms, especially in 3 day-old worms, revealed protruded anterior body in glandular lumens of crypt. Some sections of anterior body were bifurcated or sacculated. 3. The worms collected from fixed intestinal mucosa under dissecting microscope exhibited a variety of postures. Many worms showed flat shapes with a concavity or curvatures. However, in many worms, the anterior body made a single or multiple protrusions. 4. By SEM observation of protruded anterior body, a longitudinal groove was found. 5. The frequency of worms with protruded anterior body decreased in 9 days, 4 weeks and 10 weeks than in 3 day-old worms. The above findings indicated that the anterior body of juvenile and adult M. yokogawai protruded to lumens of glandular crypt by folding their lateral portions to make a reversible tubelike structure. Frequent multiple protrusions were considered to be made to adapt the microniche of glandular crypts of dog intestine.

• Food Science and Preservation
• /
• v.20 no.5
• /
• pp.659-667
• /
• 2013

This study was performed to determine the effects of the blanching condition (immersion ratio 1:15 (w/v) for 3 min at $95^{\circ}C$, and solution containing 1% sodium chloride) and selected forming agents (dextrin DE=10, dextrin DE=20, ${\beta}$-cyclodextrin; each forming agents added 5%) on the phytochemical compounds and quality characteristics of Ligularia fischeri leaves. The moisture was not affected by the forming agent. The color of a, b and chroma values were low in the blanching treatment groups and were significantly lowest with ${\beta}$-cyclodextrin (CD). The polyphenol and flavonoid contents in the blanching treatment groups were higher than those in the non-blanching-treatment group. The ascorbic acid content was higher in the non-blanching-treatment group and was significantly highest in the group treated with dextrin (DE=10) whereas the blanching treatment groups showed lower dehydroascorbic acid content than the non-blanching-treatment group. The water absorption was higher in the non-blanching-treatment group and was significantly highest in the group treated with CD. The water solubility in the blanching treatment groups treated with dextrin (DE=20) and CD was higher than that in the blanching treatment group treated with DE=10. The total chlorophyll and chlorophyll a and b contents were high in the blanching treatment group treated with CD, and for the total carotenoid contents, the same tendency as that seen with the chlorophyll content was observed. With regard to the particle diameter, those in the blanching treatment groups were lower than that in the non-blanching-treatment group and was significantly lowest in the blanching treatment groups treated with DE=20 and CD. The result of SEM observation showed that the spray-dried powders in blanching treatment groups treated with the DE=20 and CD forming agents had uniform particle distribution.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.6
• /
• pp.720-731
• /
• 2003

Statement of problem. The importance of fixture design and surface treatment. Purpose. The clinical success of dental in plants is affected by many factors such like as degree of osseointegration, the effective load dispersion for the prostheses, and a lot of attempts have been made to overcome the difficulties. In this study, efforts were made to find the possibility of clinical acceptance of the dental implants of newly designed surface and resorbable blast media surcace. Materials and methods. In this study, two groups of custom-made, screw-shaped implants were prepared. The first with the consisting of Branemark clone design and the other with the new design. These implants were divided into four groups according to the kinds of surface treatment. Four implants($AVANA^{(R)}$, Osstem, Busan, Korea)of each group were installed in twenty rabbits. Group A was consisted of Branemark done implant left as machined, Group B with Branemark clone implants with RBM(Resorbable blast media) surface, Group C with newly designed implants left as machined and Group D with newly designed implants with RBM surface. One of the twenty rabbits died from inflammation and the observation was made for six weeks. Specimens from four groups were observed using scanning electron microscopy with 40, 100, 1000 magnification power and microsurface structures were measured by white-light scanning interferometry for three dimensional surface roughness measurements(Accura $2000^{(R)}$, Intek-Plus, Korea.). Removal torque was measured in 17 rabbits using digital torque gauge(MGT 12R, Mark-10 corp., NY, U.S.A.) immediately after the sacrifice and two rabbits were used for the histologic preparation(EXAKT $310^{(R)}$, Heraeus Kulzer, wehrheim, Germany) of specimens and observed under light microscope. Resonance frequency measurement($Osstell^{(R)}$) was taken with the 19 rabbits at the beginning of the implant fixation and immediately after the sacrifice. Results. Following results were taken from the experiment. 1. The surface of the RBM implants as seen with SEM had rough and irregular pattern with reticular formation compared to that of fumed specimens showing different surface topographies. 2. The newly designed implant with RBM surface had high removal torque value among four groups with no statistical significance. The average removal torque was $49.95{\pm}6.70Ncm$ in Group A, $51.15{\pm}4.40Ncm$ in Group B, $50.78{\pm}9.37Ncm$ in Group C, $51.09{\pm}4.69Ncm$ in Group D. 3. The RFA values were $70.8{\pm}4.3Hz$ in Group A, $71.8{\pm}3.1Hz$ in Group B, $70.9{\pm}2.5Hz$, $72.7{\pm}2.5Hz$ in Group D. Higher values were noted in the groups which had surface treatment compared to the untreated groups with no statistical significance. 4. The results from the histomorphometric evaluation showed a mean percentage of bone-to-implant contact of $45{\pm}0.5%$ in Group A, $55{\pm}3%$ in Group B, $49.5{\pm}0.5%$ in Group C, and $55{\pm}3%$ in Group D. Quite amount of newly formed bone were observed at the surface RBM-treated implants in bone marrow space.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.4
• /
• pp.142-153
• /
• 2011

'Silla Monument Stone in Jungseong-ri, Pohang' was discovered in Pohang City, Gyeongsangbuk Province of Korea in 2009. The monument stone with irregular shape has dimensions of maximum height of 105cm, width of 47.6~49.6cm, thickness of 13.8~14.7cm and weight of 115kg. The results of monument stone was found to be granitite. Conservation treatment procedure was carried out in the order of production of Weathering map, cleaning of surface pollutants, consolidation using ethyl silicate. Black pollutant(crust) that covered more than 60% of the surface was analyzed first in order to remove the pollutants on the surface of the monumental stone by cleaning of surface pollutants using laser. The purpose on analysis was not only to verify the pollutants on the stone but also to carry out preliminary cleaning by securing rocks with same pollutant as the monumental stone. As the results of analysis using p-XRF(PMI. INNOV-X, USA) on the site, high level of Mn and Fe were detected, and the analysis of small section that had been fallen off with SEM/EDX for the purpose of quantitative analysis also detected high level of Mn. The Similar contaminants on Stone secured in the manner described above were made into 10 samples ($5cm{\times}5cm$) and was subjected to preliminary cleaning by Nd-YAG Laser(Laser&Physics, Korea). The results of surface observation through portable microscope during cleaning revealed that the power of 460mJ, wavelength of 1064nm and irradiation frequency of 1,800~2,300 per $25cm^2$ were most effective. Evaluation on the preservative treatment was made through confirmation of the extent of removal through color-difference meter measurement and component analysis prior to and following removal of the pollutants. As the result of color-difference meter measurement increase in the brightness was evidenced by the increase in the brightness ($L^*$)value from 33 to 49, and it was possible to ascertain the reduction in the pollutants as the content of Mn was reduced by about 80% from $50,000{\pm}5,000ppm$ to $10,000{\pm}2,000pmm$ from the result of component analysis.