• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.307-315
• /
• 2001

The purpose of this study was to provide the evaluation and prediction of strengths of SB latex modified concrete(LMC) using a statistical method and factorial experimental design method. The main experimental variables were as follows ; W/C ( 4 levels ; 31, 33, 35, 42%), S/a( 2 levels ; 55, 58%) and L/C(2 levels ; 5, 15%). The compressive strength and flexural strength of LMC were selected as a factor of response. The statistical method was carried out to analyze the results, together with factorial experimental design method and response surface method. The analysis showed that if L/C had been 15%, W/C appeared to be around 33% to achieve the design strength of $350kgf/cm^2$. In this case, the flexural strength and the slump came to around $68kgf/cm^2$ and 18cm, respectively. Eventhough the L/C varied, the design strength and W/C could be predictable together with slump value and flexural strength. As a result of series of experiments in this study, W/C and L/C were proved to be the main factors influencing on the compressive and flexural strength of LMC. Both of strength and slump values could be predictable from the mixing proportion of LMC.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.4
• /
• pp.16-22
• /
• 1999

The quantitative analysis of SB latex contents in coating color and coated paper was investigated with FT/Raman spectroscopy. From the measured FT/IR and FT/Ramon spectra, the peaks of coating color were compared with those of each compoents . Calibration curves were obtained by the area of latex peaks and PLS method of QuantIR program. The relation of predicted values in PLS method and actual values in coating mixtures and coating layer was examined. The components of coating layer in coated paper were investigated by EDS , X-mapping and SEM, The contents of latex in z-direction were calculated in the coating layer of unknown coated paper. The latex concentration measurements of Top layer and Pre layer in double coated paper show that each layer has different value. In single coated paper, it is clear that the latex concentration is highest at the surface and decreases with an increase of depth. From those results it is indicated that the latex migrates to the coated surface. The result of this study may be applied to the binder migration study and the quality control in paper mill.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.2
• /
• pp.31-42
• /
• 1992

In this study, the relative effectiveness of antimony trioxide-containing coat on fire retardancy of plywood, particleboard and medium density fiberboard was investigated and compared through ISO ignition test and inclined panel test with non-coated ones. The results obtained were summarized as fallows: Any treated materials was not ignited in inclined panel test with 5 minutes, but only particleboard among treated ones burned in ISO ignition test with fairly delayed time. The weight loss rate of plywood decreased with the increased addition level of fire-retardant and the least values were obtained in particleboard and MDF at addition level of 7% and 5% respectively. Carbonized area of wood based materials decreased with the increased addition level of fire retardant. The temperatures of back in plywood, particleboard treated with fire-retard ant coat containing 7% $Sb_2O_3$ showed the lowest but MDF did not show any effectiveness with the increased addition level. The first flash time of plywood treated with fire retardant coat containing 9% $Sb_2O_3$, MDF and particleboard treated with fire retardant coat containing 7% $Sb_2O_3$ were 257sec., 286.4sec., 165.4sec. respectively.

• Korean Journal of Materials Research
• /
• v.31 no.12
• /
• pp.672-676
• /
• 2021

In this paper, the effect of Ni (0, 0.5 and 1.0 wt%) additions on the microstructure, mechanical properties and electrical conductivity of cast and extruded Al-MM-Sb alloy is studied using field emission scanning electron microscopy, and a universal tensile testing machine. Molten aluminum alloy is maintained at 750 ℃ and then poured into a mold at 200 ℃. Aluminum alloys are hot-extruded into a rod that is 12 mm in diameter with a reduction ratio of 39:1 at 550 ℃. The addition of Ni results in the formation of Al₁₁RE₃, AlSb and Al3Ni intermetallic compounds; the area fraction of these intermetallic compounds increases with increasing Ni contents. As the amount of Ni increases, the average grain sizes of the extruded Al alloy decrease to 1359, 536, and 153 ㎛, and the high-angle grain boundary fractions increase to 8, 20, and 34 %. As the Ni content increases from 0 to 1.0 wt%, the electrical conductivity is not significantly different, with values from 57.4 to 57.1 % IACS.

• Journal of Sensor Science and Technology
• /
• v.31 no.6
• /
• pp.371-375
• /
• 2022

Antimony-doped tin oxide (ATO) thin films, one type of transparent conductive oxide (TCO) films, were prepared on a SiO₂-coated glass substrate with different substrate temperatures by a radio-frequency magnetron sputtering system. Structural, optical, and electrical characteristics of the deposited ATO films were analyzed using X-ray diffraction, scanning electron microscopy, alpha-step, ultraviolet-visible spectrometer, and Hall effect measurement. The substrate temperature during deposition did not affect the basic crystal structure of the films but changed the grain size and film thickness. The optical transmittance of the ATO films deposited at different substrate temperatures was over 70%. The lowest sheet resistance and resistivity were 8.43 × 10² Ω/sq, and 0.3991 × 10^-2 Ω·cm, respectively, and the highest carrier concentration and mobility were 2.36 × 10²¹ cm^-3 and 6.627 × 10^-2 cm²V^-1s^-1, respectively, at a substrate temperature of 400 ℃.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1089-1098
• /
• 1994

The effect of Si3N4 addition on the microstructure and PTCR characteristics of BaTiO3 was studied. When 0.1 mol% Sb2O3-doped BaTiO3 codoped with Si3N4 (0.1, 0.25, 0.5, 0.75, and 1 wt%, respectively) were sintered, their microstructures were changed by the amount of the liquid phase as a result of eutectic reaction at 126$0^{\circ}C$. By these microstructural changes, the specific resistivity ratio($\rho$max/$\rho$min) with Si3N4 content variation of 0.1 mol% Sb2O3-doped BaTiO3 ceramics sintered at 130$0^{\circ}C$ for 1 hour varied between 3.70$\times$102(0.1 wt% Si3N4) to 1.16$\times$103 (1wt% Si3N4).

• YAKHAK HOEJI
• /
• v.44 no.3
• /
• pp.232-236
• /
• 2000

An intravenous pharmacokinetics for a new red cell substitute, PEG-hemoglobin SB1, was studied in SD rats. Total-hemoglobin and its metabolite methemoglobin in the plasma were determined using a spectrophotometer. The limit of quantitation was 0.01g/dL and the C.V for interday assay reproducibility was less than 6%. Upon intravenous administration of anticipated clinical dose, 10 ml(0.7 gHb)/kg, plasma concentration curve of total-hemoglobin was well described by one-compartment model. The $t_{\frac{1}{2}},{\;}CL_{t}$, Vd and $AUC^{0-48hr}$ were $8.23{\pm}0.96{\;}hr,{\;}0.06{\;}{\pm}{\;}0.01 {\;}dL/hr/kg,{\;}0.66{\pm}0.05{\;}dL/lg{\;}and{\;}13.6{\;}{\pm}{\;}1.01g{\cdot}hr/dL$, respectively, in male rats(n=5, $mean{\;}{\pm}{\;}SD$). Those parameters in female rats were $9.21{\;}\pm{\;}2.31{\;}hr,{\;}0.06{\;}{\pm}{\;}0.01{\;}dL/hr/kg,{\;}0.79{\pm}{\;}0.08{\;}dL/kg{\;}and{\;}13.0{\;}{\pm}{\;}2.36{\;}g{\cdot}hr/dL$, respectively. Similar kinetic profiles between males and females were also obtained from other parameters. Small amount of methemoglobin, an oxidative metabolite of SB1, was detected in the plasma of both sexes, where the $AUC^{0-48{\;}hr,m}$ and $t_{{\frac{1}{2}},m}$ were approximately $1.5{\;}g{\cdot}hr/dL$ and 20 hr, respectively. The present work provides a critical kinetic data for the effective clinical applications of PEG-hemoglobin SB1.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.6
• /
• pp.31-38
• /
• 2013

This study carried out fundamental study on the forest road pavement method of cementing the ground using the compaction equipment after laying by mixing with eco-friendly stabilizer, natural soil and water. Target strength of pavement was set to 2.0MPa and the specimen was produced per mixing ratio of cement, kinds of natural soil and curing period to evaluate the durability and unconfined compressive strength. Unconfined compressive strength test was conducted to compare strength by producing the test specimen mixing environment-friendly cement as well as the test specimen mixing cement with the same mixing ratio. To evaluate the durability, surface abrasion test and water flow resistance test were conducted. In addition, SB and GB tests were conducted using iron marble and golf ball to evaluate the walking satisfaction since it can be used by visitors due to the feature of forest road.

• Journal of Welding and Joining
• /
• v.3 no.1
• /
• pp.22-31
• /
• 1985

Hot straining embrittlement is one of the most important factors which cause the brittle fracture initiation even in the service temperature in the case of mild steel and high tensile steel. Therefore it is necessary to analyze thoroughly the hot straining embrittlement occurred in weld HAZ of the structural steels. The behaviors of plastic deformation and fracture toughness at the notch tip of the hot strained weld HAZ in structural steels (SB 41 KS, SA 588-Grade A ASTM) have been studied by the recrystallization technique and crack opening displacement (COD) test method. The obtained results are summarized as follows; 1. The plastic zone is formed at the notch tip of weld HAZ owing to nomotonic and cyclic hot stran, and the maximum plastic strain increases with the accumulated hot straining amounts. 2. The distribution of the effective strain at the plastic deformed zone in HAZ can be determined as follows; (.epsilon. over bar $_{p}$ )$_{\chi}$=.epsilon. over bar $_{cr}$ ( $R_{/chi}$/.chi.)$^{m}$ where, .epsilon. over bar $_{cr}$ : (SB 41; .epsilon. over bar $_{cr}$ = 0.2, SA 588; .epsilon. over bar $_{cr}$ = 0.1) 3. The embrittlement of weld HAZ in SB 41 and SA 588 is influenced by hot strain, and the degree of embrittlement becomes deeper with hot straining amounts. 4. The embrittlement of weld HAZ of SB 41 is not influenced by the hot straining amounts until .epsilon. over bar $_{max}$ = 0.36, $R_{\chi}$ = 0.065mm, however the embrittlement of structure in SA 588 is considerably influenced even by a small quantity of the hot straining amounts.s.

• The Korean Journal of Community Living Science
• /
• v.20 no.3
• /
• pp.413-421
• /
• 2009

The purpose of this study was to analyze the patterns and the interrelationships for meeting guidelines of three health behaviors including physical activity(PA), sedentary behavior(SB), and dietary behavior(DB) for Korean adolescents using 2007 KYRBS(Korea Youth Risk Behavior Survey) data. A cross-sectional design was used to assess 73392 middle-high school students. PA(moderate physical activity${\geqq}$5times/week, or vigorous ${\geqq}$3times/week), SB(watching TV, computer, DVD, video, etc. < 3 hr/day), and DB(servings of fruits ${\geqq}$1 times/day, or vegetables ${\geqq}$ 3 times/day) were categorized into two levels (meeting guidelines or not). Chi-squared tests were conducted to compare the prevalence of students not meeting these three health behaviors between boys and girls, and logistic linear regression was used to determine the interrelationships of three health behaviors. Students meeting guidelines for PA, SB, and DB were 31.0%(boys 42.6%, girls 18.0%), 74.7%(boys 75.4%, girls 74.0%), and 38.5%(boys 38.6%, girls 38.4%), respectively. In addition, there were significant differences between both genders for PA and SB (PA; $x^2(1)$=35175.11, p<.0001, SB; $x^2(1)$=19.44, p<.0001). Only 10.9% of students met all three guidelines and 12.4% did not meet all three. Pattern that simultaneously did not meet PA and DB were high in both boys(27.1%) and girls(37.2%). Students who did not meet DB were at greater risk of not meeting PA(Boys; OR 1.49, 95% CI 1.43 to 1.55, Girls; OR 1.42, 95% CI 1.34 to 1.50), and not meeting SB(Boys; OR 1.41, 95% CI 1.34 to 1.48, Girls; OR 1.36, 95% CI 1.29 to 1.43) compared with students who met DB. The findings of this study supported further evidence for the need of a multiple behavior approach considering gender and interrelationships among three behaviors.