• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.5
• /
• pp.27-32
• /
• 1984

In SAW filters with a small aperture, diffraction effect is not negligible and degrades the frequency response near the trap. A computer simulation program for diffraction analysis is developed, and an effective diffraction compensation method is proposed to compensate the diffraction effect. A TV-lF SAW filter was designed with the diffraction taken account by the proposed method, which satisfies given frequency specifications.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.650-656
• /
• 1995

High frequency SAW filters for cellular communications were fabricated by metallizing 36$^{\circ}$Y-X LiTaO$_3$piezoelectric substrate with IIDT type electrodes. It was found that the center frequency of the filter was lowered than as designed. In order to overcome such a drawback and enable a fine tuning of its center frequency, dielectric SiN$_{x}$ thin films were deposited on LiTaO$_3$substrate by PECVD as passivation layer and then frequency responses were also characterized. As a result, the center frequency of the filter could be shifted to a higher frequency with increasing the thickness of SiN$_{x}$ film, because SAW velocity increased with increasing the ratio of the thickness of dielectric thin film to wavelength. The insertion loss of the filter, however, became larger with increasing the thickness of SiN$_{x}$ film.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.3
• /
• pp.86-93
• /
• 1997

A Design & Simulation Tools of Surface Acoustic Wave(SAW) Filters for Mobile Communication Systems, which is based on Optimization of Impulse Samples with Object Function of Amplitude, Ripple and Group Delay Characteristics, is developed and is also evaluated by designning and simulating the SAW IF Filter for PCS. In Optimization Process, fast calculation algorithm of Object Function is proposed. With this Design Tools, Transversal SAW IF Filters can be easily designed under limited conditions of small chip size and package size. It may be also applicable to wide Band Pass Filters in future Communication Systems such as FPLMTS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.5
• /
• pp.400-410
• /
• 1988

In this paper, a fast synchronization system using SAW TDL matched filter and SAW recirculation loop not only for acquisition but also tracking in the direct sequence spread spectrum communication receiver in case of low SNR was designed and its characteristics were investigated. When signal of 16dB SNR was inputed at the receiver, the PN code of the receiver could be synchronized from the extracted signal for synchronization through SAW TDL matched filter and SAM recirculation loop for 30 recirculations. And the average synchronization time of this system was calculated. From the results, we found that this synchronization system could achieve faster synchronization of PN codes in the receiver under the circumstances of low SNR than that of using only matched filter.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.6
• /
• pp.37-42
• /
• 1983

The TV IF SAW filter if designed using the windowing method. The procedure for fabricating SAW filters is described. The filter is fabricated on the Y-cut, Z-propagation LiNbO3 wafer. The passband ripple and the smaller upper sidelobe attenuation are obseryed. Further improvements and the mass production can be expected.

• Journal of Sensor Science and Technology
• /
• v.5 no.4
• /
• pp.81-87
• /
• 1996

This paper presents the optimal design method of SAW filters with arbitrary frequency characteristics. The design program using the unconstrained nonlinear optimization method and FFT algorithm is developed for optimal design of SAW filters with arbitrary frequency characteristics. As a design example, a SAW TV IF filter with asymmetric-amplitude and nonlinear-phase frequency characteristics is designed.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.3
• /
• pp.83-90
• /
• 2001

Conventional SAW duplexer filters employ a 1/4 wavelength transmission line, which causes difficulty in fabrication of the strip line on the package. Its manufacturing process is also complicated, because it needs integrating process of the separate transmitting filter, receiving filter and isolation circuits. This paper concerns development of a new structure of the duplexer filter that has all the transmitting filter, the receiving filter and the isolation circuit as a one chip device. For composition of the duplexer, we design the component SAW ladder filters and the isolation network consisting of lumped inductor and capacitor elements. Performance of the whole duplexer is optimized by the nonlinear multivariable minimization of a proper target function, and the result is compared with that of commercial filters.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.4
• /
• pp.23-30
• /
• 1999

In this study, we propose a new optimization algorithm for a withdrawal weighted SAW transversal filter to satisfy given, specifications such as bandwidth, ripple, insertion loss, and sidelobe rejection level. An analysis tool for the withdrawal weighted filter has been produced by means of the delta function model, and has been applied to the design of a filter consisting of an uniform input IDT and a withdrawal weighted output IDT. This optimization algorithm consists of three routines, which eventually determines eight design parameters to satisfy the performance specifications. At the first step, the number of input and output IDT fingers and their geometrical size are determined by the insertion loss specification. At the next step, the bandwidth is controlled by the change of the IDT finger position. Finally, the sidelobe rejection level is modified through the add/skip technique of IDT fingers. The algorithm in this paper is distinct from conventional techniques in that it can simultaneously consider all the specifications such as bandwidth, ripple, sidelobe rejection level and insertion loss, and optimize the geometry of the withdrawal weighted SAW filter.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.8-13
• /
• 2006

Recent RF SAW filters are made using a HTCC package with a CSP(chip scale Package) technology. This paper describes a development of a new $1.4{\times}1.1\;and\;2.0{\times}1.4mm$ RF SAW liters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2374-2381
• /
• 2007

.We have studied to obtain the properly conditions about impedance matching of the SAW filter for the SPUDT type and the bidirectional transducer type later. And we have studied to obtain the SAW filter for the Slanted Finger Interdigital Transducer(SFIT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator In case the SPUDT, we have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000{\AA}$ and $3.6{\mu}m$, respectively. And the of the bidirectional transducer, the width of IDT' fingers and the space between IDT' finger and reflector is $1.8{\mu}m$, respectively. Also, we have performed to series connected the SPUDT type with the bidirectional transducer type filter. The frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bahdwidth at the 3dB is probably 5.3MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.3dB and insert loss is probably -20dB after when we have matched impedance.