• Journal of Sensor Science and Technology
• /
• v.28 no.2
• /
• pp.101-105
• /
• 2019

ZnS substrates with excellent transmittance in the mid-infrared region ($3-5{\mu}m$) were prepared using hot pressing instead of conventional chemical vapor deposition (CVD). Diamond-like carbon(DLC) was coated on either one or both sides of the ZnS substrates to improve their mechanical properties and transmittance. More specifically DLC was coated using CVD with an Ar and $C_2H_2$ mixed gas, and Ge was used as the bonding layer. During CVD, the bias voltage was fixed to 500 V and analyzed by Fourier transform infrared spectroscopy (FT-IR), nanoindenter, scanning electron microscope and energy dispersive spectrometry. Results of hardness analysis using the nanoindenter, showed that DLC coating increased from 5.9 to 17.7 GPa after deposition. The FT-IR spectroscopy results showed that, in the mid-infrared region ($3-5{\mu}m$), the average transmittance of the samples with DLC coating on one and both sides increased by approximately 6% and approximately 11.2% respectively. In conclusion, the DLC coating improved the durability and transmittance of the ZnS substrates.

• Journal of Sensor Science and Technology
• /
• v.32 no.3
• /
• pp.154-158
• /
• 2023

This study aimed to improve the moisture resistance of salt cores by investigating the suitability of a two-dimensional kaolinite colloidal solution and a commercially available SiO₂ ink solution as coating agents. X-ray diffraction analysis (XRD) results showed that the intercalation of urea into kaolinite did not significantly change its layer structure. Scanning electron microscopy (SEM) images revealed that the dip-coating only affected the surface of the salt core, and the texture of the surface is differ depending on the coating solution. The humidity absorption test results showed that both coatings reduced the hygroscopicity of the salt core by more than 50%. However, in the water-solubility test, the kaolinite dissolved with the salt core, whereas the SiO₂-coated salt core left a residue. These results strongly suggest that with the coating of the exfoliated kaolinite solution, salt core will remain stable in humid environments.

• Journal of Sensor Science and Technology
• /
• v.32 no.3
• /
• pp.159-163
• /
• 2023

Salt cores have attracted considerable attention for their application to the casting process of electric vehicle parts as a solution to ecological issues. However, the salt core still has low mechanical strength for use in high-pressure die casting. In this study, we investigated the improvements in the bending strength of KCl-based salt cores resulting from the use of reinforcing materials. KCl and Na₂CO₃ powders were used as matrix materials, and glass fiber and carbon fiber were used as reinforcing materials. The effects of carbon fiber and glass fiber contents on the bending strength properties were investigated. Here, we obtained a new fiber-reinforced salt core composition with improved bending strength for high-pressure die casting by adding a relatively small amount of glass fiber (0.3 wt%). The reinforced salt core indicates the improved properties, including a bending strength of 49.3 Mpa, linear shrinkage of 1.5%, water solubility rate of 16.25 g/min·m² in distilled water, and hygroscopic rate of 0.058%.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.1
• /
• pp.163-171
• /
• 2009

Precaution is important in cardiac disease above all things. However, current developed tele-monitoring devices limit their communication distance by 100 m and have disadvantage that the device must be activated by the patients themselves. To overcome these shortcomings, we design and implement a cardiac disease management system by sending abnormal ECG signals automatically to the PC in hospital using mobile networks. Experiments show that ECG signals of the patients are transmitted to the database server in hospital without any distortion. Moreover, the amount of SMS data decreased by more than 30% using base64 method than hexadecimal one.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.151-157
• /
• 2023

Integrating dielectric materials into LTCC is a convenient method to increase the integration density in electronic circuits. To enable co-firing of the high-k and low-k dielectric LTCC materials in a multi-material hetero-laminate, the shrinkage characteristics of both materials should be similar. Moreover, thermal expansion mismatch between materials during co-firing should be minimized. The alternating stacking of an LTCC with silica filler and that with calcium-zirconate filler was observed to examine the use of the same glass in different LTCCs to minimize the difference in shrinkage and thermal expansion coefficient. For the LTCC of silica filler with a low dielectric constant and that of calcium zirconate filler with a high dielectric constant, the amount of shrinkage was examined through a thermomechanical analysis, and the predicted appropriate fraction of each filler was applied to green sheets by tape casting. The green sheets of different fillers were alternatingly laminated to the thickness of 500 ㎛. As a result of examining the junction, it was observed through SEM that a complete bonding was achieved by constrained sintering in the structure of 'calcium zirconate 50 vol%-silica 30 vol%-calcium zirconate 50 vol%'.

• Journal of Powder Materials
• /
• v.16 no.6
• /
• pp.442-448
• /
• 2009

$ZrB_2$-based composites are candidate materials for ultra-high temperature materials (UHTMs). $ZrB_2$ has become an indispensable ingredient in UHTMs, due to its high melting temperature, relatively low density, and excellent resistance to thermal shock or oxidation. $ZrB_2$ powders are usually synthesized by solid state reactions such as carbothermal, borothermal, or combined carbothermal reaction. SiC is added to this system in order to enhance the oxidation resistance of $ZrB_2$. In this study, $ZrB_2$?based composites were successfully synthesized and densified through two different processing paths. $ZrB_2$ or $ZrB_2$ 25 vol.%SiC was fully synthesized from oxide starting materials with reducing agents after heat treatment at 1400$^{\circ}C$. Besides, $ZrB_2$?20 vol.%SiC was fully densified with $B_4C$ as a sintering additive after hot pressing at 1900$^{\circ}C$. The synthesis mechanism and the effect of sintering additives on densification of $ZrB_2$ ?SiC composites were also discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.943-948
• /
• 2012

A new water energy harvester module, which is composed of piezoelectric bimorph cantilevers, harvesting circuit and a shaft with 16 impellers at a center axis, was fabricated for energy harvesting application. High energy density $Pb(Zr_{0.54}Ti_{0.46})O_3$ + 0.2 wt% $Cr_2O_3$ + 1.0 wt% $Nb_2O_5$ (PZT-CN) thick film obtained by tape casting method was used for the bimorph cantilever. The PZT-CN bimorph cantilever with a proof mass of 49 g exhibited extremely high output power of 22.5 mW (24 $mW//cm^3$) at resonance frequency of 11 Hz. In addition, the fabricated water energy harvester has a cylindrical structure with 48 bimorph cantilevers clamped at inner surface. A significantly high output power of 433 mW was obtained at a rotation speed of 120 rpm with a resistive load of $500{\Omega}$ for the water energy harvester.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.136.2-136.2
• /
• 2010

고전도성 세라믹 연결재용 $La_{0.8}Sr_{0.2}Cr_{1-x}Ti_xO_3$ (X=0.1 and 0.2) 연결재 재료의 소결도와 전기전도도에 대해서 연구하였다. 이러한 목적으로 $LaCrO_3$, $La_{0.8}Sr_{0.2}Cr_{0.8}Ti_{0.2}O_3$ (LSCT82), $La_{0.8}Sr_{0.2}Cr_{0.9}Ti_{0.1}O_3$ (LSCT91) 분말들을 공침법을 통해 합성하였으며, 결정구조는 X-ray Diffraction(XRD)를 통해 확인하였다. 소결 특성은 주사 전자현미경을 통해 분석하였고 전기 전도도는 직렬 4-단자 법으로 측정하였다. 상대 밀도 분석으로부터 도핑된 $LaCrO_3$는 $LaCrO_3$보다 더 높은 소결성을 나타내었고, 입자 크기가 작을수록 소결성이 향상하는 것을 확인 할 수 있었다. 다양한 소결온도에서 얻은 LSC, LSTC 시편들의 XRD 결과는 LSC와 LSTC의 소결성이 2차상의 상전이와 밀접한 관련이 있다는 사실을 나타내었다. 다시 말해, LSTC는 $1300^{\circ}$이상 LSC는 $1400^{\circ}C$ 이상에서 2차상이 융해됨으로써 소결성을 현저하게 향상시킨다는 것을 알 수 있었다. 그리고 비슷한 상대밀도를 가진 LSC와 LSTC의 전기 전도도를 비교 측정한 결과, LSTC가 LSC보다 더 높은 전기 전도도를 나타낸다는 것을 알 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.1
• /
• pp.57-63
• /
• 2003

The effects of glass addition on the low-temperature sintering and microwave dielectric properties of $BaO-Nd_2O_3-TiO_2$ dielectric ceramics were studied. When 10∼13 wt% of lithium borosilicate glass was added, the sintering temperature decreased from 130$0^{\circ}C$to 850-$900^{\circ}C$relative density of more than 97% was obtained. When the sample was sintered at $850^{\circ}C$ with 10 wt% of glass, the dielectric properties of $\epsilon_r{\ge}54$, $Q{\times}f_0{\ge}2300$, and $\tau_f{\ge}+8ppm/^{\circ}C$ were obtained.

• Applied Microscopy
• /
• v.47 no.3
• /
• pp.203-207
• /
• 2017

A homogeneous $KNbO_3$ (KN) phase was formed by sintering at $1,040^{\circ}C$ for 1 hour, without formation of the $K_2O$-deficient secondary phase even though suffering the minor loss of $K_2O$. KN liquid phase was formed during sintering and abnormal grain growth occurred in this specimen. The detailed microstructural observations on KN during sintering were carried out using high resolution transmission electron microscopy. The ledged structures were found at the KN grain boundary and the abnormal grain growth was performed by the lateral migration of these ledges in the presence of the liquid phase. The liquid pockets were found in the KN grains. They have various external shapes mainly due to the kinetic factors. They have atomically flat interfaces with some ledges with one atomic height. The slight deficient $K_2O$ by evaporation might somewhat reduce the melting point of KN from the reported at $1,058^{\circ}C$. The liquid pockets play an important role in supplying the liquid phase during the abnormal grain growth in the sintering process of KN ceramics.