• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 추계학술발표회요약집
• /
• pp.207-207
• /
• 2001

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.118-119
• /
• 2014

원전 운전 중 2차계통 구성재료가 부식되어 철 산화물이 증기발생기 내부로 유입된다. 유입된 철산화물은 고온고압의 환경에서 침적되어 슬러지가 된다. 침적된 슬러지는 증기발생기 전열관 재료에 응력부식균열(SCC)을 일으키는 주원인으로 원전에서는 철 산화물의 유입을 최소화하기 위해 기동전 2차계통을 순환 세정하고 있다. 해외 원전에서는 고분자 아크릴산(Polyacrylic Acid)을 순환세정시 주입함으로써 2차계통 철 산화물 제거 효율을 높인 사례가 있었다. 이에 우리 원전에서도 기동전 순환세정시 고분자 아크릴산을 주입 적용하였다. 고분자 아크릴산 주입 전 필수적으로 이뤄져야할 연구는 고분자 아크릴산이 재료에 미치는 영향평가이다. 본 연구에서는 고분자 아크릴산 농도(1, 10, 100 ppm)에 따라 2차계통 구성재료인 SA106 Gr.B와 Alloy 690의 건전성에 미치는 영향를 수행하였다. 평가방법으로는 전기화학 분극실험, 시편을 침지시켜 실험 전, 후 무게 감량을 이용한 부식률 측정, 표면 상태분석등을 이용하여 종합적으로 평가하였다. 전기화학 분극실험과 부식률 측정결과, 고분자 아크릴산 농도가 높을수록 부식은 증가하였고 고분자 아크릴산 농도 100 ppm일 때 최대 부식률이 0.037 mils로 계산되었다. 이는 부식허용 기준치(5.8 mils)보다는 100배이상 낮았으며 표면분석 결과 고분자 아크릴산으로 인한 pitting 부식은 발생하지 않았다. 이와 같은 결과로 기동시 환경에서 고분자 아크릴산 농도 100 ppm까지는 재료 건전성에 미치는 영향은 거의 없는 것으로 판단된다.

• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.3003-3011
• /
• 2021

A FAC (flow-accelerated corrosion) test was performed for a straight pipe composed of the SA335 Gr P22 and SA106 Gr B (SA106-SA335-SA106) types of steel with welds as a function of the flow rate in the range of 7-12 m/s at 150 ℃ and with DO < 5 ppb at pH levels ranging from 7 to 9.5 up to a cumulative test time of 7200 h using the FAC demonstration test facility. Afterward, the experimental pipe was examined destructively to investigate opposite effects as well as entrance effects. In addition, the FAC rate obtained using a pipe specimen with a 50 mm inner diameter was compared with the rate obtained from a rotating cylindrical electrode. The effects of the complicated fluid flows at the elbow and orifice of the pipeline were also evaluated using another test section designed to examine the independent effects of the orifice and the elbow depending on the distance and the combined effects on orifice and elbow. The tests were performed under the following conditions: 130-150 ℃, DO < 5 ppb, pH 7 and a flow rate of 3 m/s. The FAC rate was determined using the thickness change obtained from commercial room-temperature ultrasonic testing (UT).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.351-356
• /
• 2001

A potential loss of structural integrity due to aging of nuclear piping may have a significant effect on the safety of nuclear power plants. In particular, failures due to the erosion and corrosion defects are a major concern. As a result, there is a need to assess the remaining strength of pipe with erosion/corrosion defects. In this paper, a limit load solution for the eroded and corroded SA106 Grade B pipes subjected by internal pressure is developed. based in 3-D finite element analyses, considering a wide range of the shape of pipeline, flaw depth and axial flaw length parametrically.

• Corrosion Science and Technology
• /
• 제14권2호
• /
• pp.47-53
• /
• 2015

Recently, the bending process is greatly applied to fabricate the pipe line. Bending process can reduce welding joints and then decrease the number of inspection. Thus, the maintenance cost will be reduced. Induction heat bending process is composed of bending deformation by repeated local heat and cooling. By this thermal process, corrosion properties and microstructure can be affected. This work focused on the effect of induction heating bending process on the properties of ASME SA106 Gr. C low carbon steel pipes. Microstructure analysis, hardness measurements, and immersion corrosion test were performed for base metal and bended area including extrados, intrados, crown up, and down parts. Microstructure was analyzed using an optical microscope and SEM. Hardness was measured using a Rockwell B scale. Induction heat bending process has influenced upon the size and distribution of ferrite and pearlite phases which were transformed into finer structure than those of base metal. Even though the fine microstructure, every bent area showed a little lower hardness than that of base metal. It is considered that softening by the bending process may be arisen. Except of I2, intrados area, the others showed a similar corrosion rate to that of base metal. But even relatively high rate of intrados area was very low and acceptable. Therefore, it is judged that induction heat bending process didn't affect boric acid corrosion behaviour of carbon steel.

• Journal of Welding and Joining
• /
• 제35권1호
• /
• pp.26-33
• /
• 2017

This study aims to investigate the suitability of requirement for post-weld heat treatment(PWHT) temperature when different P-No. materials are welded, which is defined by ASME Sec. III Code. For SA-516 Gr. 60 and SA-106 Gr. B carbon steels that are typical P-No. 1 material, simulated heat treatment were conducted for 8 h at $610^{\circ}C$, $650^{\circ}C$, $690^{\circ}C$, and $730^{\circ}C$, last two temperature falls in the temperature of PWHT for P-No. 5A low-alloy steels. Tensile and Charpy impact tests were performed for the heat-treated specimens, and then microstructure was analyzed by optical microscopy and scanning electron microscopy with energy-dispersive spectrometry. The Charpy impact properties deteriorated significantly mainly due to a large amount of cementite precipitation when the temperature of simulated heat treatment was $730^{\circ}C$. Therefore, when dissimilar metal welding is carried out for P-No. 1 carbon steel and different P-No. low alloy steel, the PWHT temperature should be carefully selected to avoid significant deterioration of impact properties for P-No. 1 carbon steel.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.162-169
• /
• 2012

본 논문은 초음파 적외선 열화상과 위상잠금 방법을 이용하여 이종금속용접(STS304 and SA106 Gr. b)된 파이프의 응력부식균열 결함을 검출하였다. 초음파 가진장치는 출력 250 Watt, 주파수 20 kHz이었다. 실험 결과 이종금속용접부의 파이프 내부에 위치한 균열을 적외선 열화상을 이용하여 검출할 수 있었다. 실제 PT검사를 통하여 배관 내부의 균열이 하나가 아닌 일정한 범위 안에 하나 이상의 크랙이 존재하여 열화상 이미지 상에 넓은 범위의 hot spot 이미지를 만들어 냈음을 파악할 수 있었다. 또한 기존 기술로 검출이 용이하지 못한 마이크로 폭의 미세균열을 검출할 수 있었다. 또한, 초음파탐상기술은 $10\;{\mu}m$ 미세크랙의 폭을 갖은 균열을 쉽게 검출하지 못하였다. 그러나 초음파 적외선 열화상 기술은 결함 검출하였다.

• Corrosion Science and Technology
• /
• 제12권6호
• /
• pp.274-279
• /
• 2013

Flow accelerated corrosion (FAC) of the carbon steel piping in nuclear power plants (NPPs) has been major issue in nuclear industry. During the FAC, a protective oxide layer on carbon steel dissolves into flowing water leading to a thinning of the oxide layer and accelerating corrosion of base material. As a result, severe failures may occur in the piping and equipment of NPPs. Effect of alloying elements on FAC of pipe materials was studied with rotating cylinder FAC test facility at $150^{\circ}C$ and at flow velocity of 4m/s. The facility is equipped with on line monitoring of pH, conductivity, dissolved oxygen(DO) and temperature. Test solution was the demineralized water, and DO concentration was less than 1 ppb. Surface appearance of A 106 Gr. B which is used widely in secondary pipe in NPPs showed orange peel appearance, typical appearance of FAC. The materials with Cr content higher than 0.17wt.% showed pit. The pit is thought to early degradation mode of FAC. The corrosion product within the pit was enriched with Cr, Mo, Cu, Ni and S. But S was not detected in SA336 F22V with 2.25wt.% Cr. The enrichment of Cr and Mo seemed to be related with low, solubility of Cr and Mo compared to Fe. Measured FAC rate was compared with Ducreaux's relationship and showed slightly lower FAC rate than Ducreaux's relationship.

• Corrosion Science and Technology
• /
• 제11권6호
• /
• pp.257-262
• /
• 2012

Flow accelerated corrosion (FAC) of the carbon steel piping in nuclear power plants (NPPs) has been major issue in nuclear industry. Rotating cylinder FAC test facility was designed and fabricated and then performance of the facility was evaluated. The facility is very simple in design and economic in fabrication and can be used in material and chemistry screening test. The facility is equipped with on line monitoring of pH, conductivity, dissolved oxygen(DO), and temperature. Fluid velocity is controlled with rotating speed of the cylinder with a test specimen. FAC test of SA106 Gr. B carbon steel under 4 m/s flow velocity was performed with the rotating cylinder at DO concentration of less than 1 ppb and of 1.3 ppm. Also a corrosion test of the carbon steel at static condition, that is at zero fluid velocity, of test specimen and solution was performed at pH from 8 to 10 for comparison with the FAC data. For corrosion test in static condition, the amount of non adherent corrosion product was almost constant at pH ranging from 8 to 10. But adherent corrosion product decreased with increasing pH. This trend is consistent with decrease of Fe solubility with an increase in pH. For FAC test with rotating cylinder FAC test facility, the amount of non adherent corrosion product was also almost same for both DO concentrations. The rotating cylinder FAC test facility will be further improved by redesigning rotating cylinder and FAC specimen geometry for future work.