• Fashion & Textile Research Journal
• /
• v.15 no.6
• /
• pp.1000-1009
• /
• 2013

Well-fitting riding breeches provide a comfortable ride. Horse-riding breeches should fit the lower body with patches located on the inside of hip and knees to prevent tears and slips. This study provides information about the fit of women's breeches using 3D human body scan data wearing commercially available two breeches according to posture. To get information about breeches fit, we measured the angle of waist line, the length, and the area of the breeches fit on four 20's women. This research showed the problem which was down for waist back line in the case of the horseback riding pose. The back waistline of the riding breeches should be raised compared to the front waistline; subsequently, an increased waistline angle results in less back waistline decrease. The breeches have plenty of length from back waist to crotch so the breech fit can be improved. The thigh circumference increased when riding in the front; therefore, good elasticity of the weft direction of the fabric is recommended. The length increase and the peripheral increase of the front knee significantly increased the surface area of the knee; consequently, knee patch material should be a two-way elastic fabric in all directions to enhance comfort according to riding motion.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.18 no.1
• /
• pp.71-78
• /
• 2016

The present study was performed to examine the high temperature adaptability with CO₂ treatment for tomato under the condition of greenhouse cultivation during summer season. The plants with the CO₂ concentration of 1000 ppm recorded higher scores in Fm/Fo and Fv/Fm but lower score in Fo than others through the measurement of chlorophyll fluorescence, which implicated that the plants with the CO₂ concentration of 1000 ppm had more adaptability to high temperature than the others. At the condition of the same air temperature as 30℃ and 40℃, the photosynthetic rate was increased with the increase of CO₂ concentration. When in the high air temperature state of 40℃, although the photosynthic rate was low in comparison with 30℃, its value was about 18.5umolm^-2s^-1 in case of 1000ppm. The higher concentration of CO₂ made the more activated anti-oxidation enzyme (superoxide dismutase and peroxidase) for the both cultivars as 'momotaro' and 'minichal'. The cultivar of 'minichal' performed the high temperature limit as 41℃ at the CO₂ condition of 500 ppm and 43℃ at the CO₂ condition of 1000 ppm through the estimation on the variation of chlorophyll fluorescence Fo by CO₂ concentrations.

• Fisheries and Aquatic Sciences
• /
• v.17 no.3
• /
• pp.319-324
• /
• 2014

An 8 weeks feeding trial was carried out to evaluate the effects of dietary microbial phytase (P) supplementation on nutrient digestibility, and body composition in juvenile olive flounder Paralichthys olivaceus fed soybean meal-based diets. Seven experimental diets were formulated to be isonitrogenous and isocaloric to contain 50.0% crude protein (CP) and 16.7 kJ of available energy/g with or without dietary phytase supplementation. White fish meal (FM) provided 92.4% of the total protein in the basal diet ($S_0$), in the other 6 diets, 30% or 40% FM protein was replaced by soybean meal: 70% FM + 30% soybean meal ($S_{30}$); 70% FM + 30% SM + 1000 U phytase/kg diet ($S_{30}P_{1000}$); 70% FM + 30% SM + 2000 U phytase/kg diet ($S_{30}P_{2000}$); 60% FM + 40% SM ($S_{40}$); 60% FM + 40% SM + 1000 U phytase/kg diet ($S_{40}P_{1000}$); and 60% FM + 40% SM + 2000 U phytase/kg diet ($S_{40}P_{2000}$). After two weeks of the conditioning period, triplicate groups of 25 fish initially averaging $6.15{\pm}0.04g$ ($mean{\pm}S.D.$) were randomly distributed into the aquarium and were fed one of the experimental diets for 8 weeks. After feeding trial, supplementation of phytase significantly improved the apparent digestibility coefficients of phosphorus in flounder diets (P<0.05) containing 30% and 40% soybean meal regardless the levels. However, phytase had no significant influence on growth performance and whole body composition of fish. Based on the experimental results, we conclude that dietary supplementation of phytase could improve the apparent digestibility coefficient of phosphorus in olive flounder.

• Fashion & Textile Research Journal
• /
• v.5 no.4
• /
• pp.408-412
• /
• 2003

The micro structure of POY was modified and a wool-like touch yarn of composite fibers with different shrinkage was made. With this yarn 12 different fabrics with wool like touch were prepared. The characteristic physical property changes of the fabrics examined are as follows: 1. In all cases, the initial high shrinkage stages were observed in hot water treatment and the 3D images of complex multilayer of typical doubling fibers with different shrinkage were also observed in hot air treatment of 170C. 2. The tensile strength changes of satin and plain fabrics with the change of twist count showed similar behavior. However, WT's were slightly higher and RT's was lower in twill and satin fabrics than those in plain fabric. 3. Since a slight decrease of B's of twill fabric found with increasing twist count under given experimental condition, it could be influenced on the anti-drape stiffness was decreased and flexibility was increased. 4. A significant decrease of G values was observed in the twist count 800-1000 T.P.M However, in the twist count higher than 1000 T.P.M G values observed were kept nearly constant. 5. MIU of plain and twill fabrics showed a drastic decrease at the twist count higher than 1000 T.P.M.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.756-768
• /
• 2023

Neutron transport calculations are extremely challenging due to the high computational cost of large and complex problems. A multilevel octree grid algorithm (MLTG) of discrete ordinates method was developed to improve the modeling accuracy and simulation efficiency on 3-D Cartesian grids. The Balakovo-3 VVER-1000 neutron dosimetry benchmark is calculated to verify and validate this numerical technique. A simplified S₂ synthetic acceleration is used in the MLTG calculation method to improve the convergence of the source iterations. For the triangularly arranged fuel pins, we adopt a source projection algorithm to generate pin-by-pin source distributions of hexagonal assemblies. MLTG provides accurate geometric modeling and flexible fixed source description at a lower cost than traditional Cartesian grids. The total number of meshes is reduced to 1.9 million from the initial 9.5 million for the Balakovo-3 model. The numerical comparisons show that the MLTG results are in satisfactory agreement with the conventional S_N method and experimental data, within the root-mean-square errors of about 4% and 10%, respectively. Compared to uniform fine meshing, approximately 70% of the computational cost can be saved using the MLTG algorithm for the Balakovo-3 computational model.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.3
• /
• pp.41-47
• /
• 1999

Ion implanted GaAs MESFET with low resistive layer was fabricated using Si diffusion into GaAs from SiN. During the thermal annealing at 95$0^{\circ}C$ for 30s, Si diffused into ion implanted region of GaAs from SiN and they formed low resistive layer of 350$\AA$ thickness. The diffusion of Si decreased the sheet resistance of source and drain region from 1000$\Omega$/sq. to 400$\Omega$/sq. and the AuGe/Ni/Au ohmic contact resitivity from 2.5$\times$10sub -6$\Omega$-cmsup 2 to $1.5\times$10sup -6$\Omega$-cmsup 2. The fabricated lum gate length MESFET with Si diffused surface layer shows the transconductance of 360ms/mm, 8.5dB of associated gain and 3.57dB of minimum noise figure at 12GHz. These performances are better than that of MESFET without Si diffused layer.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.26-29
• /
• 2004

S-PVA is a new technology which enables screen quality advantages over S-IPS and MVA, including high transmittance, >1000:1 contrast ratio, sub-10ms response time, and wide angle of view with no off-axis image inversion and undetectable gamma distortion. This new technology will be described in detail. This paper also addresses the other remaining performance issues facing LCD-TV, including Samsung's plans for addressing these challenges. For example, until recently, inter-gray response time and associated motion blur were significant issues for achieving LCD-TV images quality. Samsung has invented DCC-II technology to achieve sub-10ms response time, and this achievement is described herein. Other technology advancements, including next-generation color performance and ultra-low black performance and improvement of off axis image quality are also discussed in this paper.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.396-401
• /
• 2004

In this paper, a 1MW HAWT(FIL-1000) rotor blade has been designed by BEMT(Blade Element Momentum Theory) with Prandtl's tip loss. Also, a 3-D flow and performance analysis on the FIL-1000 rotor blade has been carried out by using the 3-D Navier-Stokes commercial solver (CFX-5.7) to provide more efficient design techniques to the large-scale HAWT engineers. The rated power and itsapproaching wind velocity at design point (TSR=7.5) are 1MW and 9.99m/s respectively. The rotor diameter is 54.5m and the rotating speed is 26.28rpm. Airfoils such as FFA W-301, DU91-W-250, DU93-W-210, NACA 63418, NACA 63415 consist of the rotor blade from hub to tip. Recent CFX version, 5.7 was adopted to simulate 3-D flow field and to analyze the performance characteristics of the rotor blade. Entire mesh node number is about 730,000 and it is generated by ICEM-CFD to achieve better mesh quality The predicted maximum power occurringat the design tip speed ratio is 931.45kW. Approaching to the root, the inflow angle becomes large, which causesthe blade to be stalled in the region. Therefore, k-$\omega$ SST turbulence model was used to predict the quantitative flow information more accurately. Application of commercial CFD code to optimum blade design and performance analysis was proved to be more effective environment to HAWT blade designers.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.83-88
• /
• 2017

In this paper, a 3-port waveguide circulator of Ka-band millimeter-wave for isolation between transmit channel and receive channel at high power transmit mode is designed and fabricated for the seeker of the guided missile and circulator performance is verified through the S-parameter, high power and operation temperature test. At the configuration design, interface design between a seeker antenna and the circulator is considered and half-height of standard waveguide is applied for minimum and light weight body. The shape of permanent magnet and ferrite is optimized by simulation and tuning dielectrics at each port are placed for the best performance. In Fc(center frequency)${\pm}1000MHz$, designed waveguide circulator has below -20 dB return loss, below 0.5 dB insertion loss and below -23 dB isolation. It is found that circulator characteristics is similar to design results.

• Journal of the Korean Chemical Society
• /
• v.11 no.4
• /
• pp.165-169
• /
• 1967

Eine neue Methode zur Herstellung von Meßpraparation wird die Bestimmng der Spurenelemente Quecksilber, Kupfer, Blei, Zink, Nickel, Kobalt und Eisen durch Rontgenflureszenzspektrometrie entwickelt. Die Spurenelemente werden aus waßrigen Losungen durch Einleitung von Schwefelwasserstoff mit Aluminiumsulfat als Trager bei pH8 ausgefallt. Die Niederschlage der Metallsulfide werden uber Membranfilter filtriert, mit Gelatine fixiert und ihre Absolutmengen durch Rontgenfluoreszenz analyse bestimmt. Bei der geringen Dicke der auszumessenden Schichten treten Matrixeffekte nicht auf. Durch den Zusatz von Aluminiumsulfat-Trager wird eine gute Reproduzierbarkeit erzielt: Quecksilber, Kupfer, Blei, Zink, Nickel und Kobalt werden bei einer Konzentration von 50 bis 1000 p.p.b. mit einer relativen Standard-abweichung von 5.0% und Eisen bei einer Konzentration von 50∼1000 p.p.d. mit einer relativen Standardabweichung von 6.1% gemessen.