• ETRI Journal
• /
• v.22 no.1
• /
• pp.38-46
• /
• 2000

The extraction of model parameters for embedded passive components is crucial for designing and characterizing the performance of multichip module (MCM) substrates. In this paper, a method for optimizing the extraction of these parameters using genetic algorithms is presented. The results of this method are compared with optimization using the Levenberg-Marquardt (LM) algorithm used in the HSPICE circuit modeling tool. A set of integrated resistor structures are fabricated, and their scattering parameters are measured for a range of frequencies from 45 MHz to 5 GHz. Optimal equivalent circuit models for these structures are derived from the s-parameter measurements using each algorithm. Predicted s-parameters for the optimized equivalent circuit are then obtained from HSPICE. The difference between the measured and predicted s-parameters in the frequency range of interest is used as a measure of the accuracy of the two optimization algorithms. It is determined that the LM method is extremely dependent upon the initial starting point of the parameter search and is thus prone to become trapped in local minima. This drawback is alleviated and the accuracy of the parameter values obtained is improved using genetic algorithms.

• Journal of Power System Engineering
• /
• v.21 no.2
• /
• pp.20-26
• /
• 2017

This study was carried out to investigate the effect of precipitate on the high temperature deformation stability of incoloy 825 alloy. $Cr_{23}C_6$ carbide was precipitated under $950^{\circ}C$, but was not detected over $1,000^{\circ}C$. Most of the precipitation consist of $Cr_{23}C_6$ carbide. Strain-rate sensitivity was the highest in 0.01/s and the lowest in 10/s. Strain-rate sensitivity was decreased sharply below $950^{\circ}C$. In the temperature between $850^{\circ}C{\sim}1,150^{\circ}C$, plastic instable area did not exist. It showed the lowest Ziegler Parameter value of 0.06 Ziegler Parameter was the lowest as 0.06 at $850^{\circ}C$ with 10s-1 of strain. The highest Ziegler Parameter value(0.43) was found in plastic deformation at $1,050^{\circ}C$ with 0.01s-1 of strain. It tends to have an higher resistance to the high temperature deformation under $950^{\circ}C$, due to the precipitation.

• Advances in nano research
• /
• v.8 no.4
• /
• pp.307-322
• /
• 2020

In this article, free vibration of double-walled carbon nanotubes (DWNT) based on nonlocal Kelvin's model have been investigated. For this purpose, a nonlocal Kelvin's model is established to observe the small scale effect. The wave propagation is employed to frame the governing equations as eigenvalue system. The influence of nonlocal parameter subjected to different end supports has been overtly examined. The new set of inner and outer tubes radii investigated in detail against aspect ratio. The influence of boundary conditions via nonlocal parameter is shown graphically. Due to small scale effect fundamental frequency ratio decreases as length to diameter ratio increases. Small scale effect becomes negligible on all end supports for the higher values of aspect ratio. With the smaller inner tube radius double-walled CNT behaves more sensitive towards nonlocal parameter. The results generated furnish the evidence regarding applicability of nonlocal model and also verified by earlier published literature.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.817-819
• /
• 1995

Applied by periodic Stimulating Currents in Bonhoeffer-Van der Pol(BVP) model, chaotic and periodic phenomena occured at specific conditions. The conditions of the chaotic motion in BVP comprised 0.7182< $A_{1}$ <0.792 and 1.09< $A_{1}$ <1.302 proved by the analysis of phase plane, bifurcation diagram, and lyapunov exponent. To control the chaotic motion, two methods were suggested by the first used the amplitude parameter $A_{1}$,$A_{1}={\varepsilon}((x-x_{s})-(y-y_{s}))$ and the second used the temperature parameter c, c=c$(1+ {\eta}cos{\Omega}t)$ which the values of $\eta$, ${\Omega}$ varied respectlvly, and $x_{s}$, $y_{s}$ are the periodic signal. As a result of simulating these methods, the chaotic phenomena was controlled with the periodic motion of periodisity. The feasibilities of the chaotic and the periodic phenomena were analysed by phase plane and lyapunov exponent.

• Journal of KIISE:Information Networking
• /
• v.35 no.5
• /
• pp.415-424
• /
• 2008

In this paper, we compare the QoS performance enhancement schemes according to the network architecture of mobile WiMAX system in order to improve the end-to-end QoS performance and propose QoS parameter mapping method and IP packet scheduling algorithm. To evaluate the end-to-end QoS performance, we implemented an end-to-end simulator of mobile WiMAX system using OPNET. Simulation results show that the proposed QoS parameter mapping scheme reduces the average delay of VoIP packet and improves uplink resource efficiency. And also, when the proposed IP packet scheduling algorithm is applied to the system, the end-to-end packet transmission delay of VoIP service can be reduced by 44-67 percent compared to FIFO and WRR scheduler.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.833-840
• /
• 2003

The stability of structure, effectiveness of design and construction are very important factors in soil-structure design. The design-parameter is based on the test through laboratory-test and field-test. There are two ways to obtain the design-parameter. One is to through test, and the other is through relative documents and references. Recently, statistics has been used to get reliable data. In this study, Kriging method as Geostatistics and the theory of Bayesian's inference are used and the design-parameters are obtained. As the result of this study to the design-parameter is reliable and information about soil condition and soil properties in design and construction is easily found.

• Journal of applied mathematics & informatics
• /
• v.32 no.1_2
• /
• pp.185-201
• /
• 2014

In this paper, we construct a numerical method to solve singularly perturbed one-dimensional parabolic convection-diffusion problems. We use Euler method with uniform step size for temporal discretization and exponential-spline scheme on spatial uniform mesh of Shishkin type for full discretization. We show that the resulting method is uniformly convergent with respect to diffusion parameter. An extensive amount of analysis has been carried out to prove the uniform convergence with respect to the singular perturbation parameter. The obtained numerical results show that the method is efficient, stable and reliable for solving convection-diffusion problem accurately even involving diffusion parameter.

• Smart Structures and Systems
• /
• v.18 no.6
• /
• pp.1087-1109
• /
• 2016

In this manuscript, the small scale and thermal effects on vibration behavior of preloaded nanobeams with non-ideal boundary conditions are investigated. The boundary conditions are assumed to allow small deflections and moments and the concept of non-ideal boundary conditions is applied to the nonlocal beam problem. Governing equations are derived through Hamilton's principle and then are solved applying Lindstedt-Poincare technique to derive fundamental natural frequencies. The good agreement between the results of this research and those available in literature validated the presented approach. The influence of various parameters including nonlocal parameter, thermal effect, perturbation parameter, aspect ratio and pre-stress load on free vibration behavior of the nanobeams are discussed in details.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.125-131
• /
• 2000

By using the test of signal error, model structure of an electrohydraulic servo system is determined. For determining parameter of the electrohydraulic servo system, using time discrete model of parametric method, parameters in time discrete model are searched by the least square method. By bilinear transform, we have found the model of electrohydraulic servo system in s domain. Afterwards, we have compared experimental data with simulation data by MATLAB having the identified parameter. As the result, experimental data is agreed with simulation data very well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1931-1942
• /
• 1997

A new load/displacement parameter method is developed for the cases that loads are applied to one or more points, and displacements of a structure are controlled at one or more points sinultaneously. The procedure exploits a generalized Riks method, which utilizes load/displacement parameters as scaling factors in order to analyze the post-buckling phenomena including snap-through or snap-back. A convergence characteristic is improved by employing new relaxation factors in incremental displacement parameter, particularly at the region where exhibits severe numerical instability. The improved performance is illustrated by means of numerical example.