• Journal of the Korean Chemical Society
• /
• v.47 no.1
• /
• pp.13-18
• /
• 2003

The effect of ultrasonic decomposition was introduced to develop a pretreatment method for the analysis of potassium ion in human urine by potentiometry. N-(4’-benzo-15-crown-5)-anthracene-9-imine, which has a good selectivity coefficient for potassium against ammonium, was used as an ion-selective material for the determination of potassium in urine with relatively high concentration of $NH_4{^+}$. Protenis in urine be removed by 85.1% when the sample acidified with 1.0 M $HNO_3$ was preteated for 100 s by sonication. Potential response of the membrane electrode in the pretreated urine had a slope of 54.6(${\pm}0.2,\;n=5$) mV/decade over the linear range of log $[K^+]$=-5~-1(r=0.9997). When an oxidant, $H_2O_2$, was addwd to the urine sonicated with $HNO_3$, the deproteinization increased 10% more than that in case if only $HNO_3$ and then the maximum ratio of ca. 95% was obtained. Moreover, the Nernstian slope for $K^+$ added to the urinary sample increased to 56.7(${\pm}0.1,\;n=3$) mV/decade. When the calibration curves were measured, the slopes did not vary even after the electrode was successively used 20 times with ultrasonic cleaning. The results showed that an ultrasonic pretreatment method provides simplicity in use, reduced treatment time and improved potentiometric characteristics of the membrane as the method effectively removes ca. 95% of proteins in urine.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.111-120
• /
• 2008

The characteristic of induced anisotropy is investigated in this study for the Pohang mudstone involving the cut plane discontinuity. The uniaxial and triaxial compression tests are performed for anisotropic rocks with artificial joint to look into anisotropic strength characteristics. Both the uniaxial compressive strength and triaxial compressive strength show the lowest value at the angle of cut plane, ${\beta}=30^{\circ}$ and the shoulder type of anisotropy is obtained. Anisotropy ratio (Rc) in uniaxial compression measures 9.0, whereas Rc=1.29-1.98 in triaxial compression is appeared. A series of analyses are made with the test results to derive the suitable parameter values when it is applied to the Ramamurthy (1985) failure criterion. The result of uniaxial compression test is analyzed by introducing the n-index into Ramamurthy failure criterion. The result shows that, n=l is suitable for ${\beta}=0^{\circ}{\sim}30^{\circ}$ and n=3 is suitable for ${\beta}=30^{\circ}{\sim}90^{\circ}$. To analyze the result of triaxial compression test by Ramamurthy failure criterion, anisotropy ratio in uniaxial compression test is added to Ramamurthy's equation and material constants are estimated by modified Ramamurthy's equation. When these values are applied back to Ramamurthy failure criterion, the predicted values are well fitted to the test results. And strength anisotropy for failure criteria of Jaeger (1960), McLamore & Gray (1967) and Hoek & Brown (1980) are also investigated.

• Journal of Wetlands Research
• /
• v.22 no.2
• /
• pp.121-129
• /
• 2020

This paper described a laboratory investigation of micro hydropower at lower head water in a free vortex flow. The vortex height, turbine rotation and torque for straight blade with inner curved edge, twisted blade and curved blade were investigated at the flow rate of 0.0069 ㎥/s in the inlet channel. The results showed that the optimum vortex strength occurred within the range of the diameter of basin to the outlet diameter ratios of 0.17~18.5. The power output and efficiency of straight blade were higher as compared to other blades. The highest amount of generated energy was 12.33 W, the torque was 0.91 N·m and the highest efficiency by considering effective head was 29.5 %, whereas the highest efficiency by considering vortex height was 80.5 % at the rotational speed of 132 rpm. The water vortex velocity of straight blade was about 2.8 times larger than the mean velocity in the inlet channel.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.54-59
• /
• 2012

This study dealt with effect of the grinding in SCM420H planetary gears. The hardness, tooth profile, lead and roughness of the gear surface can be improved by grinding process. Therein, the grinding techniques are widely used especially as one of the physical surface improvement methods. As the results, the gear grinding process reduced vibration and noise, and increased the life of the gear. And the gear grinding improved the surface of gear tooth in a short time and low cost, thus, it is a very important process in manufacturing industry. But nowadays, it is hard to find the detail information of gear grinding process. The test piece is a planetary gear which is used in the industrial machine. The manufacture process of the test piece contains hobbing, shaving, carburizing and grinding. This study investigated the effect of the grinding process to the physiognomy and the fatigue strength of test piece which was made by SCM420H.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.9 no.2
• /
• pp.143-150
• /
• 1976

A trial has been made to find out a new method of calculating the survival rate of a fish Population utilizing the length composition data and the characteristics of the frequency curve of the length which usually is normal distribution curve. In this paper, a stochastic method is introduced and applied to calculate the survival rate of yellow croaker caught by Korean trawlers in the Yellow Sea and the East China Sea in 1971. The results are as follows : Mean of survival rate 0.46089 Variance 0.03073 Standard deviation 0.17529 95 percent confidence interval 0.36040-0.56138.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.65-74
• /
• 2000

A five path ultrasonic and/or magnetic flowmeter were installed after valve. Five path ultrasonic flowmeter were tested to obtain it's performance in a water flow standard system and magnetic flowmeter. It's varied with straight pipe length(nD), install direction and valve position. All the results are summerized. The multi-path flowmeters(MUF) showed up to $\pm0.5{\%}$ at a 2, 4, 8, 15D spacing : the MUF was significantly better than magnetic flowmeter at disturbed flow conditions.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1591-1595
• /
• 2006

하천은 인간에게 있어 물을 공급하는 중요한 하나의 공급원인 동시에 재해를 발생시킴으로서 인간에게 큰 피해를 줄 수 있는 위험물로서 존재한다. 이러한 이면을 가진 하천은 하천 자체로는 하천의 특성이 변화하지 않으며, 인위적이나 자연적인 원인으로 변화하는 것이다. 특히 강도가 큰 강우가 발생하였을 때 하천의 특성은 크게 변화한다. 강우시 하천은 유출량 증가와 유사량의 시공간적인 변화로 인해 형상거동의 자기조절 기작을 통하여 유역밖으로 이들을 안전하게 배출시키는 기능을 발휘한다. 하천 합류부는 각기 다른 특성을 가진 두 흐름이 만나는 지점으로 흐름과 지형 둘 다 변화하며, 합류부 이후에는 그 이전과는 다른 특성을 나타낸다. 따라서 합류부는 하천의 흐름상에서 중요한 부분이라고 할 수 있다. 본 연구에서는 강릉에 위치한 경포천과 제 1지류인 위촌천이 합류하는 구간을 대상으로 하여 홍수시 첨두유량의 크기와 발생위치 및 홍수 모의기간에 따른 하상변동에 대해 연구하였다. 이를 위해 1차원 하상 변동 모형인 HEC-6를 이용하여 하상변동을 모의하고 그 결과를 실측 하상변동량과 비교분석하였다. 유입수문곡선에서 첨두유량의 발생위치는 전반부, 중앙부, 후반부로 구분하였고, 홍수모의 기간은 1년, 5년, 10년으로 하였으며 1년 이상의 수문곡선은 1년의 수문곡선을 모의 기간만큼 반복 발생시키는 것으로 하였다. 그 결과 하상변동은 홍수 모의기간, 유입수문곡선의 첨두유량 발생위치와 첨두유량의 크기에 따라 그 양상이 현저히 달라지는 것을 확인하였다. 유입유량 조건에서 동일수문곡선의 반복에 따른 모의기간 별 하상변동은 퇴적과 침식의 규모가 확대되는 형태로 나타나는 것을 알 수 있다. 미치는 시간축척의 영향을 파악하기 위해 $70{\sim}90$ 시간 동안 실험을 수행하였다. 세굴의 측정은 투명한 아크릴로 제작된 수제 내부에 CC카메라를 수제 전 후면 및 측면에 설치하여 월류수제의 세굴 발생을 실시간으로 측정하며 동시에 수제의 각 면에 각각 3개의 압력센서를 설치하여 압력분포를 측정함으로써, 월류수제 주변의 압력변화에 따른 세굴심의 실시간 변화를 비교할 수 있도록 하였다. 수심이 연중 $25{\sim}35m$를 유지하는 H호의 경우 간헐식 폭기장치를 가동하는 기간은 물론 그 외 기간에도 취수구의 심도를 표층 10m 이하로 유지 할 경우 전체 조류 유입량을 60% 이상 저감할 수 있을 것으로 조사되었다.심볼 및 색채 디자인 등의 작업이 수반되어야 하며, 이들을 고려한 인터넷용 GIS기본도를 신규 제작한다. 상습침수지구와 관련된 각종 GIS데이타와 각 기관이 보유하고 있는 공공정보 가운데 공간정보와 연계되어야 하는 자료를 인터넷 GIS를 이용하여 효율적으로 관리하기 위해서는 단계별 구축전략이 필요하다. 따라서 본 논문에서는 인터넷 GIS를 이용하여 상습침수구역관련 정보를 검색, 처리 및 분석할 수 있는 상습침수 구역 종합정보화 시스템을 구축토록 하였다.N, 항목에서 보 상류가 높게 나타났으나, 철거되지 않은 검전보나 안양대교보에 비해 그 차이가 크지 않은 것으로 나타났다.의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.10-19
• /
• 2014

We designed bearingless rotor hub system which replace mechanical hinge/bearing with composite beam component and conducted fatigue analysis for flexbeam and torque tube. Extension/bending/torsional stiffness was calculated from 2D section analysis using VABS and 2D section structure analysis was applied for strain calculation. S-N curve of each composite material was generated using Wohler equation and fatigue analysis was conducted on weakness section which was decided from static structure analysis. CAMRAD II was used for load analysis and load analysis result was applied HELIX/FELIX standard load spectrum to generate bearingless rotor system load spectrum which was used fatigue safe life analysis.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.2
• /
• pp.376-381
• /
• 2017

We were investigated by cyclic voltammetry to the stability through the electrochemical characteristics of Langmuir-Blodgett films mixed with myristic acid and stearic acid. Fatty acid mixture monolayer LB films was deposited by the LB method on the indium tin oxide(ITO) glass. The electrochemical properties was measured by cyclic voltammetry with a three-electrode system in 0.01 N $NaClO_4$ solution. The measuring range is continuously oxidized to 1650 mV, with an initial potential of -1350 mV was reduced. Scanning rates of 50, 100, 150, 200, and 250 mV/s was set. As a result, LB monolayer films of fatty acid mixture was appeared on irreversible processes by the oxidation current from the cyclic voltammogram. Diffusion coefficient (D) of fatty acid mixture was calculated $7.9{\times}10^{-2}cm^2s^{-1}$ at 0.01 N $NaClO_4$ solution.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.3
• /
• pp.45-54
• /
• 2009

This study was developed the metallic plate for bone fixation in the neurosurgery and general surgery and plates has a finn place in bone operating and treatment. The plates can be realized to bending strength and stiffness for strength estimation. Maximum point of bending curves has a bending point(P) with maximum load which to applied nearly 0.2% offset displacement. The device's sizing has a ${\Phi}13$ and ${\Phi}18$, and algorithm of strength estimation compared a plate(${\Phi}13$, ${\Phi}18$, ${\Phi}13-{\Phi}18$). The bending strength of the curved metallic plate has to evaluate maximum of a 311N, 387N, 410N, 474N. When a displacement preserve with a load, tensile stress through to press a plate is 274N, 324N, 382N, 394N. The algorithm of strength estimation can be used to support estimation of bending strength and stiffness. Their tool bring to settlement in the new basic algorithm for evidence with varied adjustment.