• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.4
• /
• pp.128-138
• /
• 1998

This paper describes a principle of the conducted noise separator which can separate the conducted noise to the common mode and differential mode(normal mode), and presents the transfer characteristics of the separator designed and manufactured. We separated the conducted noise generated from switched mode converter to the CM and DM conducted noise, and also analyzed the source and path of conducted noise in the converter by the conducted noise separator. Since we could easily get the characteristics of the CM and DM conducted noise by the separator, we could efficiently determine the contermeasures for the reduction of the conducted noise and establish the foundation of the systematic procedure for the design of low pass filter.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.5
• /
• pp.94-102
• /
• 1998

In this paper, we proposed a dynamic selection scheme of advnaced prediction mode(DAPM), which reduces computational cost and improves coding efficiency. We can select the mode between default prediction mode (DPM) and advanced prediction mode (APM) according to motion componenets in a frame dynamically. For this purpose, we defined error distribution of motion estimation (EDME) as sum of absolute difference(SAD) for each searching points. This distribution region is divided to four subregions. We calculate minimum values in each subregions and then, we determine whether block motion estimation is performed or not depending on the results. As a result, we reduced computational complexity to 30% without degradation of image quality compared to fixed APM(FAPM) by selecting DPM for linear movement.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.2
• /
• pp.184-191
• /
• 2009

This study examined small-size specimen's effectiveness that is used to evaluate floor impact sound performance. Floor impact sound level of small-size specimen is higher than full-size. This is due to excessive impact power of Bang machine. Impact hammer that has small impact power relatively can solve this problem. But, according to the size of specimen, mode shape and frequency that influence to structural borne sound is changed. Slab mode of full-size specimen was changed to frequency design of resilient materials. But in case of small-size specimen, there is no change of vibration mode by resilient materials change, Vibration mode of small-size specimen is the same. Therefore, it is not proper that use small-size specimen in floor impact sound estimation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.101-102
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.433-434
• /
• 2008

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.7A
• /
• pp.712-718
• /
• 2004

We report 1.6 Tb/s (160${\times}$10 Gb/s) WDM transmission over 2,000 km of single mode fiber using distributed hybrid(distributed Raman amplifier＋Erbium-doped fiber amplifier) optical amplifiers. After transmission over 2,000 km of single mode fiber, average optical signal to noise ratios of C/L-band were 20.5 dB, 21.9 dB, respectively. The minimum Q-factors of each band were 14.65 dB (BER=5.8e-8) in C-band, 13.75 dB (BER=5.0e-7) in L-band without forward error correction. We performed 1.6 Tb/s error-free transmission over 2,000 km of single mode fiber using Reed-Solomon (255, 239) forward error correction code.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.470-473
• /
• 2004

This paper presents conducted emission noise measurement from electronic equipment in frequency range of 1 MHz up to 30 MHz by small loop antenna. Small loop antenna measurement method can measure common-mode (CM) and differential-mode (DM) component of the noise on a pair of power line at the same time. The CM and DM can be measured separately. The theory of this measurement method is introduced and analyzed. The measured results were compared with the conventional measurement by Line Impedance Stabilization Network (LISN) and result a good trend between those methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.463-464
• /
• 2006

This paper present experimental results by non-contact mode Atomic Force Microscopy using high aspect ratio tips (HAR-T). We fabricated the carbon nanotube tip based on dielectrophoresis and the carbon nano probe by focused ion beam after dielectrophoretic assembling. In this paper, we measure AAO sample and trench structure to estimate HAR-T's performance and compared with conventional Si tip. We confirmed that results of HAR-T's performance in non contact mode was very superior than conventional tip.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.10
• /
• pp.109-117
• /
• 1999

In this paper, a direct adaptive control, based on Lyapunov Function Candidate, is applied to a nonlinear Gunner's Primary Stabilized Head Mirror system to derive a parameter adaptation scheme; furthemore, a nonlinear sliding mode control, but also compensating the error in identification of the parameters which are even varying of have uncertain values. The performance of the adaptive controller is determined by the tracking ability to a desired model under some disturbances and the slowly varying parameters of the system. Both adaptive scheme and sliding mode play an important fole in the improvement of the nonlinear system control.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.422-427
• /
• 2001

The component mode synthesis method allows the elastic deformation of each component in the flexible multibody system by a sum of modes and modal coordinates. This paper focuses on the selection of boundary conditions and deformation modes for redundantly constrained flexible components in mechanical system dynamics. The result of a flexible body dynamic analysis with only normal modes is used to identify proper boundary conditions of a static modes and a desired set of static modes which will be used in the final model. A simple four bar mechanism is used to explain the procedure and a space satellite with solar panels is analyzed using the proposed method.