• Structural Engineering and Mechanics
• /
• 제52권6호
• /
• pp.1273-1287
• /
• 2014

Plates are most widely used in the hulls of floating concrete structures, bridge decks, walls of off-shore structures and liquid storage tanks. A method of analysis is presented for the determination of load-deflection response and ultimate strength of high-strength steel fiber reinforced concrete (HSSFRC) plates simply supported on all four edges and subjected to combined action of external compressive in-plane and transverse loads. The behavior of HSSFRC plate specimens subjected to combined uniaxial in-plane and transverse loads was investigated. The proposed analytical method is compared to the physical test results, and shows good agreement. To predict the constitutive behavior of HSSFRC in compression, a non-dimensional characteristic equation was proposed and found to give reasonable accuracy.

• 소성∙가공
• /
• 제16권3호
• /
• pp.193-200
• /
• 2007

Simulations of the thermally-induced residual stresses and birefringence in freely quenched plates of polycarbonate were performed by using the linear viscoelastic and photoviscoelastic constitutive equations for the mechanical and optical properties, respectively, and the first order rate equation for volume relaxation. The predictions for the birefringence showed good agreement with experimental measurements. However, for initial temperature close to the glass transition temperature, some differences existed around the surface layer. Based on the simulation, the influences of various cooling conditions on the residual stress and birefringence in plates were investigated. The residual stress and birefringence increased with increasing initial temperature, decreasing coolant temperature and increasing heat transfer coefficient of coolants.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.258-261
• /
• 2007

Simulations of the thermally-induced residual stresses and birefringence in freely quenched plates of polycarbonate were performed by using the linear viscoelastic and photoviscoelastic constitutive equations for the mechanical and optical properties, respectively, and the first order rate equation for volume relaxation. The predictions for the birefringence showed good agreement with experimental measurements. Based on the simulation, the influences of various cooling conditions on the residual stress and birefringence in plates were investigated. The residual stress and birefringence increased with increasing initial temperature, decreasing coolant temperature and increasing heat transfer coefficient of coolants.

• 소성∙가공
• /
• 제22권5호
• /
• pp.258-263
• /
• 2013

The deformation behavior of NIMONIC 80A was studied in the high temperature range of $900{\sim}1200^{\circ}C$ and for strain rates varying between 0.02 and $20s^{-1}$ via the hot compression test. Processing maps for hot working were constructed on the basis of the power dissipation efficiency using a dynamic material model. The results showed that the strength during hot compression increased with increasing strain rate and decreasing temperature. At low strains, the processing map of NIMONIC 80A did not reveal any instability domain regardless of the strain rate and temperature. However, at high strains, the processing map exhibited an instability domain at a low strain rate of $0.2s^{-1}$ and within a temperature range of $900{\sim}960^{\circ}C$. In the instability domain, the deformed microstructure exhibited shear bands and carbide precipitation while, in the safe domain, full recrystallization occurred.

• 한국지반신소재학회논문집
• /
• 제11권2호
• /
• pp.1-9
• /
• 2012

본 연구는 이 구성모델의 실용화를 위한 검토로 응력경로에 따라 어떤 특성이 있는가를 밝히기 위하여 백마강 모래를 이용하여 등방압축팽창시험과 응력경로를 달리한 일련의 배수삼축시험(CTC, Conventional triaxial compression test), TC(Triaxial compression test), RTC(Reduced triaxial compression test), OSP(Optional stress path))을 각각 수행하여 각각의 토질매개변수를 결정한다. 그리고 각각의 응력경로에 대한 시험으로부터 결정된 토질매개변수 11개를 이용하여 토질매개변수를 결정시 이용된 시험 결과를 역해석한다. 그리고 항복함수에 관련된 토질매개변수 h와 ${\alpha}$를 파괴기준에 관련된 토질매개변수 ${\eta}_1$의 상관식과 상수로 결정한 9개의 토질매개변수를 이용하여 응력경로가 다른 경우의 응력-변형률 거동에 대한 예측의 정도를 밝히기 위하여 CTC시험, TC시험, RTC시험, OSP시험 및 Fine Silica Sand시험의 결과를 각각 해석하여 단일항복면 구성모델의 실용성을 검토한다.

• 한국전산구조공학회논문집
• /
• 제18권3호
• /
• pp.291-302
• /
• 2005

구조응답에 기여하는 중요성으로 인하여 추계론적 해석에서는 재료탄성계수의 불확실성에 의한 응답변화도에 대한 연구가 주로 진행되어 왔다. 그러나 추계론적 해석이 의미있는 값을 제공하기 위해서는 가능한 많은 인수에 대한 불확실성을 동시에 고려하여야 한다. 본 연구에서는 구조재료의 중요한 두 인수인 탄성계수와 포아송비에 나타나는 불확실성을 고려한 추계론적 해석을 위한 정식화를 평면문제에 대하여 제안하였다. 이를 위하여 이들 두 인수의 함수로 주어지는 구성행렬의 각 요소에 대한 다항식 전개를 채용하였으며, 두 인수의 불확실성에 따라 나타나는 자기 및 상호상관함수는 n-차 모멘트에 대한 일반식을 적용하여 구성하였다. 다항식 전개에 따라 부행렬의 무한합으로 변형된 구성행렬은 계산상의 편의를 위하여 요구되는 정확도 내에서 절삭하여 사용하였다. 제안된 방법의 검증을 위하여 단순 평면구조를 예제로 택하여 해석하었으며, 해석결과는 국부평균법을 채용한 고전적인 몬테카를 해석 결과와 비교하였다.

• Advances in nano research
• /
• 제8권1호
• /
• pp.25-36
• /
• 2020

Rotating systems concern with torsional vibration, and it should be considered in vibration analysis. To do this, the time-dependent torsional vibrations in a single-walled carbon nanotube (SWCNT) under the linear and harmonic external torque, are investigated in this paper. Eringen's nonlocal elasticity theory is considered to demonstrate the nonlocality and constitutive relations. Hamilton's principle is established to derive the governing equation of motion and consequently related boundary conditions. An analytical method, called the Galerkin method, is utilized to discretize the driven differential equations. Linear and harmonic torsional loads, along with determined amplitude, are applied to the SWCNT as the external torques. SWCNT is considered under the clamped-clamped end supports. In free vibration, analysis of small scale effect reveals the capability of natural frequencies in different modes, and this results desirably are in coincidence with another study. The forced torsional vibration in the time domain, especially for carbon nanotubes, has not been done before in the previous works. The previous forced studies were devoted to the transverse vibrations. It should be emphasized that the dynamical analysis of torsion is novel, workable, and at the beginning of the path. The variations of nonlocal parameter, CNT's thickness, and the influence of excitation frequency on time-dependent angular displacement and nondimensional angular displacement are investigated in the context.

• 한국추진공학회지
• /
• 제20권5호
• /
• pp.51-59
• /
• 2016

STS 321 스테인리스강은 액체 로켓 엔진을 비롯한 고온 고압의 시스템의 재료로서 많이 사용된다. 321 스테인리스강의 고온에서의 변형 거동을 예측하기 위해 Kocks의 전위 장벽 모델을 근거로 유동응력에 대한 구성 방정식을 열적 응력 요소와 비열적 응력 요소를 사용하여 제안하였다. 제안한 모델은 321 스테인리스강의 상온부터 $500^{\circ}C$의 넓은 온도 영역에서 재료의 변형 거동들을 잘 예측하였다.

• 대한조선학회논문집
• /
• 제48권3호
• /
• pp.189-199
• /
• 2011

Austenite stainless steel(ASS), aluminum alloy and nickel steel alloy are the most widely used in many cryogenic applications due to superior mechanical properties at low temperature. The Face-Centered Cubic(FCC) and Hexagonal Close-Packed(HCP) materials are used for the primary and secondary insulation barrier of Liquefied Natural Gas(LNG) carrier tank and various kinds of LNG applications currently. In this study, tensile tests of ASS, aluminum alloy and nickel steel alloy were carried out for the acquisition of quantitative mechanical properties under the cryogenic environment. The range of thermal condition was room temperature to $-163^{\circ}C$ and strain rate range was 0.00016/s to 0.01/s considering the dependencies of temperatures and strain rates. The comprehensive test data were analyzed in terms of the characteristics of mechanical behavior for the development of constitutive equation and its application.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.945-950
• /
• 2001

Vacuum interrupters that is used in various switchgear components such as circuit breakers, distribution switches, contactors, etc. spreads the arc uniformly over the surface of the contacts. The electrode of vacuum interrupters is used sintered Cu-Cr material satisfied with good electrical and mechanical characteristics. Because the closing velocity is 1-3m/s, the deformation of the material of electrodes depends on the strain rate and the dynamic behavior of the sintered Cu-Cr material is a key to investigate the impact characteristics of the electrodes. The dynamic response of the material at the high strain-rate is obtained from the split Hopkinson pressure bar test using cylinder type specimens. Experimental results from both quasi-static and dynamic compressive tests with the split Hopkinson pressure bar apparatus are interpolated to construct the Johnson-Cook equation as the constitutive relation that should be applied to simulation of the dynamic behavior of electrodes. To evaluate impact characteristic of a vacuum interrupter, simulation is carried out with five parameters such as initial velocity, added mass of a movable electrode, wipe spring constant, initial offset of a wipe spring and virtual fixed spring constant.