• The KIPS Transactions:PartC
• /
• v.15C no.5
• /
• pp.429-438
• /
• 2008

NGN is a packet-based converged network to support session and non-session services in QoS-enabled broadband transport network. QoS based resource control must be defined to support differentiated services for various network users in NGN. We designed and implemented DIAMETER protocol as the Rs interface, and also defined mapping rules between DIAMETER information elements and SDP(Session Description Protocol) attributes for QoS based resource control in NGN. We selected and implemented DIAMETER protocol among alternate resource control protocols in ITU-T as the Rw interface because of simple interworking method with Rs interface and adequate AAA functionality. We defined mapping rules of messages and information elements between Rs and Rw interfaces for resource control from a service layer to a transport layer. Based on the mapping rule of QoS information elements and the interworking method between Rs and Rw interfaces, we built up a test-bed that support differentiated delivery services.

• Journal of Advanced Navigation Technology
• /
• v.12 no.5
• /
• pp.464-469
• /
• 2008

The RS-232C (Unbalanced serial) and RS-485 (balanced serial) are standard in serial communication. RS-485 uses a differential electrical signal, as opposed to unbalanced signals referenced to ground with the RS-232. Differential transmission, which uses two lines each for transmit and receive signal results in greater noise immunity and longer distances as compared to the RS-232C. The greater noise immunity and distance are big advantages in industrial environments. In general, one protocol on one serial interface is very normal application. In this study, we implemented multi protocols on one serial RS-485 interface and examine the performance and result with hanging multi equipments.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.197-200
• /
• 2002

The current Inn technique is many problems that is permission of radio station using RF Wireless Modem, that is influence of geographic obstacle using radio wave, that is frequency interference, that is finiteness of frequency resources. In this paper, we are solved many elements, IM replaces RF Wireless Modem, we suggest transmission technique of correction message using mobile phone, we researched Interface Module development which is linkage of DGPS receiver and mobile phone. IM can transmit correction message passing RS-232 port and modem communication control. IM of base station is initialized RS-232 port and modem to move station for correction message transmission, IM waited response mode. IM of move station is initialized RS-232 port and modem, IM requests hand shaking to base station, completed connection establishment. Users are worked Differential surveying using receiving correction message between mobile phones.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.37-40
• /
• 2004

This paper is about Multi-function RFID Reader Platform that receives RF TAC data and transfer data to HOST PC through Blue-Tooth USB, RS-232 and Ethernet. This Reader system is composed of RFID Module, ARM Processor, RS-232, US5 and Ethernet Interface, etc.. The information of Tag stretches the RFID module through the antenna and is received at the ARM processor. ARM processor accomplishes the facility to deliver these informations at the PC server using the Blue-tooth Interface for the wireless and the RS-232, USB and Ethernet MAC Interface for the wire.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.3
• /
• pp.11-17
• /
• 2003

In this paper, we implemented 2-wire (data gnd) RS232C serial communication interface by applying the Collision Sensing Multiple Access(CSMA) Protocol. The transmitting and receiving wires of RS232C pert are connected together by the interface circuit forming data wire without hardware modification On two-wired common channel connection simultaneous transmission Don mere than two hosts causes data collision. The collision is detected by loop-back test of transmission data comparing with the fed back data to detect the data distortion. Various models are adopted to reduce the probability of retransmitted data collision and experiments show the performance of each cases. Due to allowing multiple hosts to be accessed through the common communication channel with minimum circuit addition the result of this paper can be easily applied for conventional RS232C instruments and machines to connect to the single data communication line.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.3
• /
• pp.467-472
• /
• 2022

The 3D ultrasonic anemometer transmits measured data by connecting PC and RS232C interface. Depending on the observation location, it is often necessary to extend the cable connecting the PC and the sensor. When installing on the test bed of the Air Meteorological Agency, the original AWM2919 cable was required to be extended because the distance between the PC container and the equipment installation site was more than 30 m. The cable was extended through a process such as extending the AWM2919 cable, converting the interface with the PC from RS232C to RS485, and testing the RS485 communication. After the equipment was installed with an extended cable, data were remotely collected and analyzed to confirm successful cable extension.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.5
• /
• pp.209-213
• /
• 2010

This paper is a study of Car safety network system using sensed data from varied sensors. This hardware will work with various sensors and communication protocols. There are many sensors. Then, I selected 3 sensors for test, which were sonic sensor for distance checking, tilt sensor for rollover and impact sensor for car accident and theft. Also, there are many interfaces for sensor. Therefore I designed hardware to support various sensor interfaces. For instance ADC(Analog to Digital converter), I2C, RS232, RS485, CAN. In this case, sonic sensor have I2C interface, tilt sensor have RS485 interface and Impact sensor have analog interface. In this research, I can gather sensing data from 3 sensors (mentioned above), and sending control signal to other processor with RS232, RS485, CAN communication. So, we can use easily this hardware for many cases of systems, which need sensors.

• Proceedings of the IEEK Conference
• /
• 2003.11a
• /
• pp.363-366
• /
• 2003

We propose the system that automatically adjusts the white balance on display products to a standard value according to several nations. We replace manual or semi-auto method with fully automatic method using windows application program. And we use RS-232C serial interface to communicate PC with display products which we want to adjust white balance. The PC generates patterns for measuring color information and Color Analyzer measures color and brightness. This value is transmitted through RS-232C serial interface to PC. The PC's algorithm analyzes this information and then decides which RGB Gain value is best for optimal white balance. This RGB Gain value is transmitted through RS-232C serial interface to display products. The modified color value is measured again and feed back to PC. This sequence is repeated until optimum white balance is obtained.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.47-47
• /
• 2000

Most measuring devices are equipped with RS-232 or GPIB interface for communicating data with computers. If the measuring devices can be accessed by a server computer, the valuable information from the devices can be effectively shared with other computers via internet. But, if the measuring devices and the server computer are too far away, it is difficulty to directly connect them by RS232 interface. PSTN(Public Switched Telephone Network) refers to the world's collection of interconnected voice-oriented public telephone networks. Measuring computer system which is equipped with RS232 interface and modem for PSTN can be introduced to overcome the aforementioned distance problem, In this work, an internet based remote monitoring system which utilizes PSTN and VRML for 3-dimensional GUI is proposed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.2
• /
• pp.123-131
• /
• 2002

ASC(Avionics System Computer) was developed to control weapon delivery and navigation sensors, and to perform man-machine interface with pilots for XKO-1 aircraft. The data communications between ASC and UFC(Up Front Controller), DC(Data Concentrator) were implemented by RS422 serial data bus. Also, SCIL(Standard Computer Interface Library) was designed to facilitate control and management of the computer hardware resources and is embedded in the ASC. These structures have a merit of noise immunity and a reduction of wire harness for signal lines, and enable OFP(Operational Flight Program) programmers to use the SCIL easily without knowing hardware details. Manufactured system was on installed on XKO-1, and peformed for BIT(Built In Test) and interface test with UFC and DC. The test results show that it meets the system requirements.