• 대한치과보철학회지
• /
• 제29권3호
• /
• pp.101-110
• /
• 1991

The purpose of this study was to compare the repaired joint strength among several edge profiles after denture repair. For this study, eight edge profiles were used for repair methods and five self-curing resin brands were used for repair materials. Break away loads were tested after 1 hr., 24 hrs. and 1 week. Instron was used for testing the transverse strength of repaired specimen. The results were as follows. 1. Repaired joint strength was about 35-65% of that of original specimen. 2. Joint strengths of round, inverse knife, inverse rabbit, lap ogee joint were higher tnan that of traditional simple butt joint 3. Joint strength of the simple butt joint was low significant. 4. Joint strengths after 1 hr. specimen were lower than those of 24 hrs. and 1 week specimens in joint strengths. 5. There were no significant differences between 24 hrs. and 1 week specimens in joint strengths. 6. It look more than 24 hours to gain satisfactory physical property after repairing the fractured denture base when self-curing resin was used for repair.

• 열처리공학회지
• /
• 제8권3호
• /
• pp.213-221
• /
• 1995

Temperature distribution, transformation and residual stresses generated during the quenching process of carbon steel. It follows many difficulties in the analytical considerations on those quenching process because of the coupling effects on temperature and metallic structures. In this paper one of the basic study on the quenching stresses was carried out for the case of the round steel bar specimen(SM45C) with 40mm both in its diameter and length. The temperature distributions considering strain hysteresis were numerically calculated by finite element technique. In calculating the transient temperature field, the heat flux between water and rod surface was determined from the heat transfer coefficient. The gradient of temperature is almost same to geometric of specimen. At early stage of the quenching process, the abrupt temperature gradient has been shown in the surface of the specimen.

• Parasites, Hosts and Diseases
• /
• 제61권3호
• /
• pp.298-303
• /
• 2023

This study aimed to describe a rare case of gnathostomiasis in the vocal cord. A 54-yearold Chinese woman living in Korea visited with a chief complaint of voice change at the outpatient department of otorhinolaryngology in Hallym Sacred Heart Hospital, Hallym University on August 2, 2021. She had eaten raw conger a few weeks before the voice change developed, but her medical history and physical examinations demonstrated neither gastrointestinal symptoms nor other health problems. A round and red cystic lesion, recognized in the anterior part of the right vocal cord, was removed using forceps and scissors through laryngeal microsurgery. The histopathological specimen of the cyst revealed 3 cross-sections of a nematode larva in the lumen of the cyst wall composed of inflammatory cells and fibrotic tissues. They differ in diameter, from 190 ㎛ to 235 ㎛. They showed characteristic cuticular layers with tegumental spines, somatic muscle layers, and gastrointestinal tracts such as the esophagus and intestine. Notably, intestinal sections consisted of 27-28 lining cells containing 0-4 nuclei per cell. We tentatively identified the nematode larva recovered from the vocal cord cystic lesion as the thirdstage larva of Gnathostoma, probably G. nipponicum or G. hispidum, based on the sectional morphologies.

• Corrosion Science and Technology
• /
• 제15권2호
• /
• pp.58-68
• /
• 2016

Many industries need the universal standard or technique to obtain the identical CCT regardless of specimen geometries. This study aimed to determine an appropriate applied torque to the cylindrical specimen defining the apparatus and the procedure to measure the temperature of initiating crevice corrosion in tubular shape products such as pipes, tubes and round rods etc; the test method also proved applicable to the plate type specimen. A series of experiments for CCT measurements with the plate type and cylindrical stainless steel specimens of various diameters with different microstructures (austenitic and duplex) and PRENs were conducted to determine the relationship among geometries on CCT. Thus, the apparatus that could measure the CCT of stainless steels with both plate and cylindrical geometries was newly designed. The use of the apparatus facilitated the same CCT value for both geometries only if the specimens were made of the same alloy. The applied torque can be calculated for various diameters of the cylindrical specimens using the following relation; Applied torque, $Nm=-0.0012D^2+0.019D+2.4463$ (D; the diameter of cylindrical specimen, mm). However, upwards of 35 mm diameter cylindrical specimens require 1.58Nm, which is the same torque for the plate type specimen; in addition, this test method cannot be used for cylindrical specimens of less than 15 mm diameter.

• 농업생명과학연구
• /
• 제43권4호
• /
• pp.33-36
• /
• 2009

Globose to clavate base-ball sized, pear shaped, fruiting bodies were found under the Himalayan cedar, Cedrus deodora at less fertile and poor sandy poor soil in the campus of Gyeongsang National University in Jinju, Korea. The fruiting body was at first, round to club-shaped, usually with a narrow, rooting base with yellowish rhizomorphs attached to it and lack a volva and a sterile base. The peridium of fruiting body was tough and crusty. The peridioles were white pea-like capsules in a blackish matrix. The color change to darker tints of brown at the top of the exterior peridium reflected the gradual ripening of the interior gleba and peridioles, which proceeded from the top downward to become a mass of spore dust, appearing as cinnamon brown at the apex of the vertical section. At around this stage, the peridium cracked open linearly, exposing the gleba with powdery spores mass released from overmatured peridioles. Spores were more or less round, warty or spiny, 10 to $12{\mu}m$; globose, cinnamon brown in powdery mass, with spines up to $2{\mu}m$ long. The thin peridium ruptured further in response to the disintegration of the peridioles, releasing the powdery spores, which proceeded until whole fruiting body disappeared leaving the dry spore dust coats in the vicinity. The absence of a capillitium is a distinctive characteristic that distinguishes the specimen from other puff-ball fungi and from most of earthballs. Based on the above characteristics, the specimen was identified as Poslithus tinctorius.

• 정보학연구
• /
• 제4권2호
• /
• pp.129-136
• /
• 2001

초음파현미경은 대부분 단순히 시료로부터 반사된 신호의 진폭만을 이용하여 초음파영상을 구성하였다. 그러나 이 방법은 미세한 변화를 가지는 시료에 대해서는 반사신호의 진폭변화가 민감하지 않음으로 인하여 영상의 질을 저하 시켰다. 본 연구에서는 초음파 반사신호의 진폭과 위상을 동시에 측정할 수 있는 초음파현미경 시스템을 구성하고 샘플로서 500원 주화와 내부에 원형결함이 존재하는 알루미늄 시료에 대해 진폭영상과 위상영상을 획득하고 이들을 상호 비교분석하였다. 실험결과, 위상영상은 미세한 높이변화에 대해서는 진폭영상에 비하여 민감한 반응을 보였고 콘트라스트가 좋은 영상을 얻을 수 있었다. 이와같은 실험결과로 위상영상은 미세변화를 갖는 시료에 대한 비파괴검사시 진폭영상으로 얻어진 영상의 모호성을 개선하는 보조도구로서 활용이 기대된다.

• 한국해양공학회지
• /
• 제5권1호
• /
• pp.97-105
• /
• 1991

In this paper, the fatigue strength and the fatigue crack propagation behaviors of the round bar specimens which were spirally built up by welding and subsequently hardened by quenching were investigated. The material used was SF60 which was whdely employed in mechanical components, especially shafts. Fatigue tests were conducted at the fully reversed condition(R=-1) and axial and load control in the room temperature ahd air environment. The experimental results were expressed by both the range of stress intensity factor ($\Delta{K}$) and the effective range of stress intensity factor ($\Delta{K}_{eff}$). It was clarified that applying of quenching after the building up welding process improved the fatigue strength and the gatigue crack propagation property in the low range of $\Delta{K}$ of the built up round bar specimen.

• Corrosion Science and Technology
• /
• 제9권5호
• /
• pp.223-232
• /
• 2010

NiTi alloy has been used for orthodontic wire due to good mechanical properties, such as elastic strength, friction resistance, and high corrosion resistance. Recently, these wire were coated by polymer and ceramic materials for aesthetics. The purpose of this study was to investigate electrochemical characteristics of tooth colored NiTi wire using various instruments. Wires (round type and rectangular type) were used, respectively, for experiment. Polymer coating was carried out for wire. Specimen was investigated with optical microscopy (OM), field emission scanning electron microscopy (FE-SEM) and energy dispersive x-ray spectroscopy (EDS). The corrosion properties of the specimens were examined using potentiodynamic tests (potential range of -1500 ~ 2000 mV) and electrochemical impedance spectroscopy (frequency range of 100 kHz ~ 10 mHz) in a 0.9 % NaCl solution by potentiostat. From the results of polarization behavior, the passive region of non-coated NiTi wire showed largely, whereas, the passive region of curved NiTi wire showed shortly in anodic polarization curve. In the case of coated NiTi wire, pitting and crevice corrosion occurred severely at interface between non-coated and coated region. From the results of EIS, polarization resistance(Rp) value of non-coated round and rectangular NiTi wire at curved part showed $5.10{\times}10^5{\Omega}cm^2$ and $4.43{\times}10^5{\Omega}cm^2$. lower than that of coated NiTi wire. $R_p$ of coated round and rectangular NiTi wire at curved part showed $1.31{\times}10^6{\Omega}cm^2$ and $1.19{\times}10^6{\Omega}cm^2$.

• 항공우주시스템공학회지
• /
• 제11권3호
• /
• pp.1-7
• /
• 2017

고주파 유도가열은 최근 활발히 연구되고 다양한 산업분야에서 적용 되고있다 본 논문에서는 산업체에서 많이 사용되고 있는 SCM440 시편을 대상으로 유도 가열한다. 시편은 지름 20mm, 길이 160 mm의 환봉으로 제작하였다 유도 가열 전원 공급 장치 모듈을 이용하여 약 85 kHz의 고주파로 환봉을 50초 동안 유도가열 하여 5초 단위로 바닥면에서 150 mm지점의 온도를 얻는다. 이 실험을 총 10회 반복하여 측정한 실험의 중앙값과 전자기-열 연동해석을 통해 환봉의 저항열과 온도에 대한 해석 결과값을 서로비교 분석하였다. 환봉의 해석모델은 표피효과를 고려하여 모델링을 하였고, 50초동안 유도가열을 했을 때의 실험의 중앙값은 $57.65^{\circ}C$ 해석값은 $57.27^{\circ}C$이다. 이 결과로 해석결과는 실험결과와 잘 일치함을 보이고, 본 해석방법으로 유도가열 현상을 수치적으로 예측할 수 있음을 보였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1998년도 춘계학술발표회논문집(2)
• /
• pp.336-343
• /
• 1998

An iteration method has been developed for determining crack growth and fracture resistance cure (J-R curve) from the load versus load-line displacement record only. In this method, the hardening curve, the load versus displacement curve at a given crack length, is assumed to be a power-law function, where the exponent varies with the crack length. The exponent is determined by an iterative calculation method with the assumption that the exponent varies linearly with the load-line displacement. The proposed method was applied to the static J-R tests using compact tension(CT) specimens, a three-point bend (TPB) specimen, and a cracked round bar (CRB) specimen as well as it was applied to the quasi-dynamic J-R tests using CT specimens. The J-R curves determined by the proposed method were compared with those obtained by the conventional testing methodologies. The results showed that the J-R curves could be determined directly by the proposed iteration method with sufficient accuracy in the specimens from SA508, SA533, and SA516 pressure vessel steels and SA312 Type 347 stainless steel.