• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.156-160
• /
• 1994

Use of engineering ceramics has been increasing due to the outstanding physical and chemical properties. Conventional machining processes, however, are not applicable due to their hardness and brittleness. Laser cutting is a promising alternative for these ceramics. In this study, experimental data of CO $_{2}$ laser cutting of $Al_{2}$ $O_{3}$ and Si $_{3}$ N $_{4}$ are obtained to give a guide in the industry. Results of $Al_{2}$ $O_{3}$ cutting showed extreme weakness to thermal crack and it was found that pulsed beam has to be used for thick $Al_{2}$ $O_{3}$ specimen. Si $_{3}$ N $_{4}$ showed good results for both CW and pulsed beams. Using pulsed beam resulted narrower kerf width with increased surface roughness a nd reduced cutting speed. It was also found that a parameter call path energy is useful for representing minimum threshold value for possible cutting range with pulsed beam.

• 한국진공학회지
• /
• 제9권4호
• /
• pp.419-427
• /
• 2000

본 연구는 원자의 주변 환경에 따른 각각의 확산 속도를 구할 수 있는 기구를 제시하였다. STM 또는 HRLEED 등의 실험과 kinetic Monte Carlo(KMC) 시뮬레이션 계산과의 비교를 통하여 테라스 위 흡착 원자의 확산장벽, step 끝 부착 원자의 탈착 확산 장벽, 잘 알려진 Schwoebel 장벽을 포함한 각각의 확산 장벽을 구할 수 있었다. 팔-넓이, 군집 밀도, 거칠기 등이 시뮬레이션 계산과 실험 결과를 비교하는 데에 가장 적절한 원자단위의 구조변수들임을 확인하였고, 특히 아직 잘 사용되지 않은 구조 계수인 가지폭이 확산 장벽을 구별하여 구하는 데에 중요한 역할을 하는 것을 확인하였다.

• 대한기계학회논문집A
• /
• 제25권2호
• /
• pp.312-322
• /
• 2001

This paper investigates the combined effects of parameters such as die surface finish, die directionality of stoning contact pressure and draw speed on the resulting coefficient of friction. Also, this study show the correlation between the NN(Neural Network) and DOE(Design of Experiments) to reduce the number of experiments without the loss of the effects of parameter upon coefficient of friction. The experiments were run in random order with at least three replicates. It was found that the directional stoning orthogonal to the pulling direction is lower friction than directional stoning parallel to the pulling directi on using FCD55 die and SPCEN.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.123-128
• /
• 2002

The machining parameters for the wire electrical discharge machining(WEDM), including no load voltage, pulse-on time, pulse-off time, wire tension, water flow rata offset etc. should be chosen properly so that a better performance can be obtained An optimum selection of machining parameters relies heavily on the operators technologies and experience. This study presents a method by means of Taguchi method to select optimal machining parameter combination for an cutting speed or surface roughness. Experimental results demonstrate that the machining models are appropriate and the derived machining parameters satisfy the real requirements in notice.

• Elastomers and Composites
• /
• 제50권4호
• /
• pp.251-257
• /
• 2015

The rubber seal is a part inserted into servo cylinder to keep the air pressure constant. In order for efficient movements of the servo cylinder, the frictional coefficient of the rubber seal needs to be minimized while the sealing is maintained. In this work the friction characteristics of rubber seal specimen are tested on metal plate at various conditions. The experimental conditions include roughness level, applied pressure, lubrication, and rubbing speed. The design of experiment approach is taken to assess the effect of each parameter. The nonlinear frictional response of the rubber is applied to the FEM model simulating the servo cylinder movement. The result demonstrates that precise optimization of the servo cylinder movement must be preceded by preliminary experiments coupled with the theory and FEM model.

• 한국도로학회논문집
• /
• 제15권5호
• /
• pp.1-9
• /
• 2013

PURPOSES : This study is to develop a method to evaluate lubrication of asphalt binder using WMA additives and compare their lubrication effects on two types of WMA additives and three types of asphalt film thicknesses. METHODS : This study is based on laboratory experiments and rheological analysis of the experimental results. Testing materials are aggregate diskes, asphalt, and WMA additives. The main testing method is stress sweep test by using dynamic shear rheometer (DSR). RESULTS : Sasobit gives more lubrication effects on film thicknesses 0.2mm and under but LEADCAP does on film thicknesses over 0.3mm. CONCLUSIONS : LVE-Limit is a better parameter to discern the lubrication effects on the thin film asphalt thickness. Both Sasobit and LEADCAP WMA additives provide effective lubrication at the compaction temperature.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.85-94
• /
• 1994

The cutting mechanism of ultrasonic vibration machining is characterized as two phases, that is, an impact at the cutting edge and a reduction of cutting force due to non-contact interval between tool and workpiece. In this paper, in order to identify cutting dynamics of a system with ultrasonically vibrated cutting tool, an ARMA modeling is performed on experimental cutting force signals which have a dominant effect on cutting dynamics. The aim of this study is, through Dynamic Date System methodology, to find the inherent characteristics of an ultrasonic vibration cutting process by considering natural frequency and damping coefficient. Surface roughness and stability of cutting process under ultrasonic vibration are also considered

• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.77-83
• /
• 2004

Cutting by a high speed laser cutting machine is one of most effective technologies to improve productivity. This paper has studied to obtain the cutting characteristics and optimal cutting conditions in a high speed feeding type laser cutting machine by Tacuchi method in design of experiments. A Lf(34) orthogonal array is adopted to study the effect of adjustment parameter. The adjustment parameters consist of cutting speed, laser power, laser output duty and assistant gas pressure. And the quality feature is selected as surface roughness of sheet metal. Variance analysis is performed in order to evaluate the effect of adjustment parameters on the quality feature of laser cutting process.

• 한국기계기술학회지
• /
• 제13권3호
• /
• pp.31-37
• /
• 2011

The purpose of this study is to investigate cutting characteristics and wear behavior in SCM440 steel with different cutting tools, CBN(Cubic Boron Nitride) and coated CBN. During the test coated CBN tool especially with TiAlN showed better wear resistance behavior than orginal CBN tools. In the interrupted cutting condition, axial groove affected tool surface with impact force during the turning operation. For advantageous turning parameter in the interrupted process it is recommendable that lower speed. Also surface roughness showed better behavior in the coated CBN tool conditions than normal CBN conditions. Mainly this is caused by reduced friction between material and tool surface with coated layer.

• Structural Engineering and Mechanics
• /
• 제57권1호
• /
• pp.21-43
• /
• 2016

A conditional probability based approach known as Particle Filter Method (PFM) is a powerful tool for system parameter identification. In this paper, PFM has been applied to identify the vehicle parameters based on response statistics of the bridge. The flexibility of vehicle model has been considered in the formulation of bridge-vehicle interaction dynamics. The random unevenness of bridge has been idealized as non homogeneous random process in space. The simulated response has been contaminated with artificial noise to reflect the field condition. The performance of the identification system has been examined for various measurement location, vehicle velocity, bridge surface roughness factor, noise level and assumption of prior probability density. Identified vehicle parameters are found reasonably accurate and reconstructed interactive force time history with identified parameters closely matches with the simulated results. The study also reveals that crude assumption of prior probability density function does not end up with an incorrect estimate of parameters except requiring longer time for the iterative process to converge.