• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1379-1385
• /
• 2014

Even the rough prediction of the product test time before the lifetime test of mechanical component begins would be of use in estimating cost and deciding how to keep up with the test. The reliability predictions of mechanical components are difficult because failure or degradation mechanisms are complicated, and few plausible databases are available for lifetime prediction. Therefore, this study conducted lifetime predictions of elastomeric U seals that were respectively installed in a hydraulic actuator and a pneumatic actuator using lifetime models and a field database based on failure physics and an actual test database obtained from the NSWC handbook. To validate the results, the predicted failure rates were compared with the actual lifetime test results acquired in the lab durability tests. Finally, this study discussed an engineering procedure to determine the coefficients in the failure rate models and analyzed the sensitivity of each influential parameter on the seal lifetime.

• Journal of Korea Foundry Society
• /
• v.18 no.4
• /
• pp.340-348
• /
• 1998

C/V graphite iron has superior tensile strength, toughness and ductility than grey iron, and better castability than ductile iron. The retained austenite content of C/V graphite iron by austempering treatment affects on the mechanical properties such as ductility, hardness, wear properties and machinability. C/V graphite iron alloyed with Cu and Mo were carried out on the austenitizing at $900^{\circ}C$ for 1 hour, and the austempering at $240{\sim}400^{\circ}C$ for 1 hr. And then the mechanical and wear properties of austempered C/V graphite iron have been investigated by the retained austenite content. In consequence, the retained austenite content was found to be 18.2% in austempering temperature at $240^{\circ}C$, and was increased 39.2% at $400^{\circ}C$. Tensile strength and hardness of austempered C/V graphite iron were decreased as the retained austenite content increased, but elongation was increased. The rolling wear loss were increased as the retained austenite content increased. The wear surface of as-cast became to be rough. The microstructure of austempered C/V graphite iron was became to be acicular ausferrite in austempering at $240^{\circ}C$, and feathery ausferrite at $400^{\circ}C$.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.6
• /
• pp.455-471
• /
• 2013

Active sonar has been commonly used to detect targets existing in the shallow water. When a signal is transmitted and returned back from a target, it has been distorted by various properties of acoustic channel such as multipath arrivals, scattering from rough sea surface and ocean bottom, and refraction by sound speed structure, which makes target detection difficult. It is therefore necessary to consider these channel properties in the target signal simulation in operational performance system of active sonar. In this paper, a monostatic active sonar system is considered, and the target echo, reverberation, and ambient noise are individually simulated as a function of time, and finally summed to simulate a total received signal. A 3-dimensional highlight model, which can reflect the target features including the shape, position, and azimuthal and elevation angles, has been applied to each multipath pair between source and target to simulate the target echo signal. The results are finally compared to those obtained by the algorithm in which only direct path is considered in target signal simulation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.986-989
• /
• 2003

In the steel production line, the molten metal of a furnace is transformed into slab material and then move to the hot strip line, This paper describe about the real time recognition system of material management number, which is marked at the surface of a slab in the steel production line. This recognition processing should be performed before the slab is moved to the hot strip line. This system include following recognition steps. First, we remove noise from the captured slab image by use pre-filter. Second, we extract rough area, which is include slab number and then, we extract individual number area. Finally, we recognize material management number by use KLT(Karhunen-Loeve transform) algorithm. We applied our system to the real slave image, which was captured in the process line. In the results, we recognized slave number to the 94% accuracy.

• Korean Journal of Materials Research
• /
• v.21 no.8
• /
• pp.461-467
• /
• 2011

Cu(In, Ga)$Se_2$ (CIGS) precursor films were electrodeposited on Mo/glass substrates in acidic solutions containing $Cu^{2+}$, $In^{3+}$, $Ga^{3+}$, and $Se^{4+}$ ions at -0.6 V (SCE) and pH. 1.8. In order to induce recrystallization, the electrodeposited $Cu_{1.00}In_{0.81}Ga_{0.09}Se_{2.08}$ (25.0 at.% Cu + 20.2 at.% In + 2.2 at.% Ga + 52.0 at.% Se) precursor films were annealed under a high Se gas atmosphere for 15, 30, 45, and 60 min, respectively, at $500^{\circ}C$. The Se amount in the film increased from 52 at.% to 62 at.%, whereas the In amount in the film decreased from 20.8 at.% to 9.1 at.% as the annealing time increased from 0 (asdeposited state) to 60 min. These results were attributed to the Se introduced from the furnace atmosphere and reacted with the In present in the precursor films, resulting in the formation of the volatile $In_2Se$. CIGS precursor grains with a cauliflower shape grew as larger grains with the $CuSe_2$ and/or $Cu_{2-x}Se$ faceted phases as the annealing times increased. These faceted phases resulted in rough surface morphologies of the CIGS films. Furthermore, the CIGS layers were not dense because the empty spaces between the grains were not removed via annealing. Uniform thicknesses of the $MoSe_2$ layers occurred at the 45 and 60 min annealing time. This implies that there was a stable reaction between the Mo back electrode and the Se diffused through the CIGS film. The results obtained in the present research were sufficiently different from comparable studies where the recrystallization annealing was performed under an atmosphere of Ar gas only or a low Se gas pressure.

• Korean Chemical Engineering Research
• /
• v.58 no.2
• /
• pp.273-279
• /
• 2020

In this study, conventional solvent extraction (CSE), microwave-assisted extraction (MAE), and ultrasound-assisted extraction (UAE) were compared for the recovery of paclitaxel from biomass. As a result of investigating the effect of the extraction solvent type (acetone, chloroform, ethanol, methanol, methylene chloride), methanol was the most suitable for all extraction methods. In the case of MAE and UAE using methanol, most of the paclitaxel (> 95%) was recovered by only one extraction. The recovery rate of paclitaxel increased with the increase of extraction temperature (25-45 ℃), microwave power (50-150 W), and ultrasonic power (180-380 W) for MAE and UAE. In addition, SEM analysis showed that the biomass surface structure was slightly corrugated in CSE, while in the MAE and UAE, it was very rough and destroyed by strong impact.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.23 no.3
• /
• pp.695-699
• /
• 2009

UV irradiation causes skin-aging involving coarse wrinkles, thickening, dyspigmentation, and rough skin surface. This study was carried out to develop health & functional food by using Korean red ginsneg and Fagopyrum esculentum extract mixture (RGFE) for prevention of skin wrinkles. The RGFE-treated group showed the more effective collagenase inhibition rate than the red ginseng (RG)-treated group. To investigate photo protective effects of RGFE on UV-induced damaged skin, SKH hairless male mice were orally administerd RGFE and regional treatment and irradiated with UV for up to 8 weeks. In RGFE-treated group, better skin, and less wrinkle formation were observed compared with UV group. Epidermal thickness of hairless mouse was significantly decreased in RGFE, RG, and Fagopyrum esculentum (FE) groups compared with UV group. These results demonstrate RGFE have photo-protective effects on UV-damaged hairless mouse skin.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.7
• /
• pp.113-123
• /
• 2000

In the navigation for a mobile robot, the collision avoidance with unexpected obstacles is essential for the safe navigation and it is independent of the technique used to control the mobile robot. This paper presents a new collision avoidance algorithm using neural network for the safe navigation of the autonomous mobile robot equipped with CAN and ultrasonic sensors. A tracked wheeled mobile robot has a stability and an efficiency to move on a rough ground. And its mechanism is simple. However it has difficulties to recognize its surroundings. Because the shape of the tracked wheeled mobile robot is a square type, sensor modules are generally located on the each plane surface of 4 sides only. In this paper, the algorithm using neural network is proposed in order to avoid unexpected obstacles. The important character of the proposed algorithm is to be able to detect the distance and the angle of inclination of obstacles. Only using datum of the distance and the angle, informations about the location and shape of obstacles are obtained, and then the driving direction is changed. Consequently, this algorithm is capable of real time processing and available for a mobile robot which has few sensor modules or the limited sensing range such as a tracked wheeled mobile robot. Effectiveness of the proposed algorithm is illustrated through a computer simulation and an experiment using a real robot.

• Journal of Soil and Groundwater Environment
• /
• v.16 no.6
• /
• pp.66-78
• /
• 2011

It is getting difficult to manage water resources in South Korea because more than half of annual precipitation is concentrated in the summer season and its intensity is increasing due to global warming and climate change. Artificial recharge schemes such as well recharge of surface water and roof-top rainwater harvesting can be a useful method to manage water resources in Korea. In this study, potential artificial recharge site is evaluated using geographic information system with hydrogeological and social factors. The hydrogeological factors include annual precipitation, geological classification based on geological map, specific capacity and depth to water level of national groundwater monitoring wells. These factors were selected to evaluate potential artificial recharge site because annual precipitation is closely related to source water availability for artificial recharge, geological features and specific capacity are related to injection capacity and depth to water is related to storage capacity of the subsurface medium. In addition to those hydrogeological factors, social aspect was taken into consideration by selecting the areas that is not serviced by national water works and have been suffered from drought. These factors are graded into five rates and integrated together in the GIS system resulting in spatial distribution of artificial recharge potential. Cheongsong, Yeongdeok in Gyeongsangbuk-do and Hadong in Gyeongsangnam-do, and Suncheon in Jeollanam-do were proven as favorable areas for applying artificial recharge schemes. Although the potential map for artificial recharge in South Korea developed in this study need to be improved by using other scientific factors such as evaporation and topographical features, and other social factors such as water-curtain cultivation area, hot spring resorts and industrial area where groundwater level is severely lowered, it can be used in a rough site-selection, preliminary and/or feasibility study for artificial recharge.

• The Journal of Engineering Geology
• /
• v.8 no.3
• /
• pp.215-224
• /
• 1998

In this study, total strain was measured by LVDTs and local strains on the surface of specimens were measured by strain gauges. And axi-symmetrically elastoplastic FEM analyses was carried out for cylindrical specimens. Considering the influence of the restraint induced by the loading platen, in the case of H/D=1, the strain distribution on the side of a specimen is obviously affected by the condition of platen contact. Furthermore, it is clear that the larger H/D ratio becomes, the smaller the influence to the strain distribution is. For the smooth contact condition, the strain on the side is not influenced by the stiffness of the specimen, the shape and the scale effect, the strain distribution coincides with the nominal total strain. Whereas, in the case of rough contact condition, the strain distribution is remarkably affected. It is made clear that strain responses of hard rock specimens may more sensitive than these of soft rock specimens as a results of interaction between loading platens and specimen and the uniaxial strength of specimens may strongly depends on this interaction and stress-strain relation is affected by the contact condition.