• 한국소음진동공학회논문집
• /
• 제20권1호
• /
• pp.36-44
• /
• 2010

The accurate prediction of dynamic characteristics of high speed rotors, such as gas turbines, is important to avoid the possibility of operating the machinery near the critical speeds or unstable speed regions. However, the dynamic analysis methods and softwares for gas turbines have been developed in the process of producing many gas turbines by manufacturers and most of them have seldom been disclosed to the public. Recently, commercial FEM softwares, such as SAMCEF, ANSYS and NASTRAN, started supporting some rotordynamics analysis modules based on 3-D finite elements. In this paper, the dynamic analysis method using commercial S/W, especially ANSYS, is attempted for the small-size gas turbine engine rotor, and the analysis capability and limitations of its rotordyamics module are evaluated for further improvement of the module. As the preliminary procedure, the rotordyamic analysis capability of ANSYS was tested and evaluated with the reference models of the well-known dynamics. The limitations in application of the rotordynamics module were then identified. Under the current capability and limitations of ANSYS, it is shown that Lee diagram, a new frequency-speed diagram enhanced with the concept of $H{\infty}$ in rotating machinery, can be indirectly obtained from FRFs computed from harmonic response analysis of ANSYS. Finally, it is demonstrated based on the modeling and analysis method developed in the process of the S/W verification that the conventional Campbell diagram, Lee diagram, mode shapes and critical speeds of the small-size gas turbine engine rotor can be computed using the ANSYS rotordynamics module.

• Tribology and Lubricants
• /
• 제39권6호
• /
• pp.268-272
• /
• 2023

This study explores the characteristics of tilting pad journal bearings used in the high-speed rotating shaft systems of centrifugal compressors. A centrifugal compressor is a high-speed rotating machine that is widely used to compress gases or vapors employed in various industrial applications. It transfers the centrifugal force of a fast-spinning impeller to the fluid and compresses it under high pressure. Many high-speed rotating shaft systems, which require high stability, use tilting pad journal bearings. The characteristics of these bearings can vary depending on several properties, and identifying the appropriate characteristics is essential to optimize the design on a case-to-case basis. In this study, the authors perform a time-dependent analysis of the properties of tilting pad journal bearings and the rotordynamics of the rotating shaft system using COMSOL Multiphysics software. Specifically, the authors analyze the characteristics of the tilting pad journal bearings by performing a parametric sweep using parameters such as pad clearance, maximum tilting angle, preload, number of pads, and pad pivot offset. The authors then use the results of the bearing-characteristics analysis to evaluate the vibration of the rotating shaft and verify its operation within a desirable range. The understanding gained from this study will allow us to determine the optimal properties of these bearings and the limiting operational speed using COMSOL Multiphysics software.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1271-1272
• /
• 2013

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.157-158
• /
• 2011

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.496-497
• /
• 2012

• 소음진동
• /
• 제8권3호
• /
• pp.450-456
• /
• 1998

A rotordynamic analysis is performed with a centrifuge rotor-bearing system for the raing speed of 100,000 rpm. The system is composed of a centrifuge rotor(or simply the rotor), flexible shaft, motor rotor and shaft, and two support rolling element bearings of the motor shaft. Design goals are to achieve wide separation margins of critical speeds and favorable unbalance responses of the rotor at the associated critical speeds. The latter requirements are especially important as the system crosses multiple numbers of critical speeds and as the system may not have enough separaton margins around the rating speed. As the system adopts an extra-flexible shaft, it is shown that the rotor has satisfactory small unbalance responses over higher criticals while having an unsatisfactory large one at the first critical. To supress this a bumper ring or guide bearing needs to be installed at a suitable location of the flexible shaft. It is also shown that even with the flexible shaft the dynamics of the motor must be incoporated into the full system model to accurately identify the fourth critical speed, which is close to the rating speed, and higher ones. The analysis is based on the finite element method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.388-392
• /
• 2002

Fault tolerant control algorithm for heteropolar magnetic bearings are presented. This fault tolerant control utilizes grouping of currents as C-cores in order to isolate magnetic fluxes. Hardware requirements to maintain fault tolerant control are reduced since decoupling chokes are not required in this control scheme. The currents supplied to each pole are redistributed, if some coils fail suddenly, such that the resultant magnetic forces should remain invariant through coil failure events. Load capacity before magnetic saturation is reduced through coil failures while maintaining the same magnetic forces before and after failure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.342.2-342
• /
• 2002

Fault tolerant control algorithm fer heteropolar magnetic bearings are presented. This fault tolerant control utilizes grouping of currents as C-cores in order to isolate magnetic fluxes. Hardware requirements to maintain fault tolerant control are reduced since decoupling chokes are not required in this control scheme. The currents supplied to each pole are redistributed, if some coils (ail suddenly, such that the resultant magnetic forces should remain invariant through coil failure events. (omitted)

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.119-125
• /
• 1999

This article proposes the analytical and experimental approaches for the reduction of vibration generated in the gear box of an NC machine. The lateral critical speed of main spindle and torsional natural frequencies were analyzed and the impact testing of gear box was performed. These results were compared with the forced operating speeds, The vibration was much diminished by redesign of gear module and reinforcement of box structure.

• Tribology and Lubricants
• /
• 제28권6호
• /
• pp.265-271
• /
• 2012

In the preceding Part I study, for improving the unbalance response vibration of a large PRT motor-generator rotor fundamentally by design, a series of design analyses were carried out for bearing improvement by retrofitting from original plain partial journal bearings, applied for operation at a rated speed of 1,800 rpm, to final tilting pad journal bearings. To satisfy evenly key basic lubrication performances such as the minimum lift-off speed and maximum oil-film temperature, a design solution of 5-pad tilting pad journal bearings and maximizing the direct stiffness by about two times has been achieved. In this Part II study, a detailed rotordynamic analysis of the large PRT motor-generator rotor-bearing system will be performed, applying both the original plain partial journal bearings and the retrofitted tilting pad journal bearings, to confirm the effect of rotordynamic vibration improvement after retrofitting. The results show that the rotor unbalance response vibrations with the tilting pad journal bearings are greatly reduced by as much as about one ninth of those with the plain partial journal bearings. In addition, for the tilting pad journal bearings there exist no critical speed up to the rated speed and just one instance of a concerned critical speed around the rated speed, whereas for the plain partial journal bearings there exist one instance of a critical speed up to the rated speed and two instances of concerned critical speeds around the rated speed.